Skip to content

Lifting & Rigging

801 SKUs

Showing 433–480 of 801 SKUs

Grade 100 Swivel Eye Nut — dimension drawing

Grade 100 Swivel Eye Nut — 0.3–4.5 t WLL

Alloy steelAs supplied by the manufacturer
Inquire
Blue Grade 100 eye hook with safety latch (shortening clevis link listing)

Grade 100 Shortening Clevis Link — 2,700–22,600 lbs WLL

5.5 mm (7/32″) to 16 mm (5/8″)Powder coated
Inquire
Four-leg chain sling with sling hooks, type QOS (Grade 80 sling shown)

Grade 100 Four-Leg Chain Sling with Sling Hooks — Type QOS, 3–56 t WLL

3 to 56 t, legs up to 45° from vertical6 mm to 26 mm chain
Inquire
Grade 100 four-leg chain sling with grab hooks, type QOG

Grade 100 Four-Leg Chain Sling with Grab Hooks — Type QOG, 3–56 t WLL

3 to 56 t, legs up to 45° from vertical6 mm to 26 mm chain
Inquire
Grade 100 Connecting Link, Non-Removable — dimension drawing

Grade 100 Connecting Link — Non-Removable, 4,300–35,300 lbs WLL

4,300 to 35,300 lbs7 mm (9/32″) to 20 mm (3/4″)
Inquire
Red Grade 100 clevis foundry hooks, wide throat and clevis pin, two views

Grade 100 Clevis Foundry Hook — 2.5–16 t WLL

Alloy steel, quenched and temperedPowder coated
Inquire
Category image · Lifting & Rigging
Galvanized Steel Hook on Plate — dimension drawing

Galvanized Steel Hook on Plate — 8 mm

Hot dipped galvanizedCarbon steel
Inquire
Galvanized Shackle — Italian Type — dimension drawing, bow, screw pin

Galvanized Shackle — Italian Type, 70–20,000 kg WLL

5 mm to 63 mmHot dipped galvanized / powder coated / zinc plated
Inquire
Galvanized Rigging Screw, Closed Body — dimension drawing, eye and eye

Galvanized Rigging Screw, Closed Body — 0.1–11 t WLL

Cold-drawn seamless steel tube C1020Hot-dip galvanized / electro-galvanized / self colour
Inquire

Questions we get asked

About this range

01What is the difference between WLL, SWL and breaking load?
WLL — working load limit — is the most the manufacturer rates a part to carry in service. SWL, safe working load, is the older term and is sometimes set lower for a particular installation. The minimum breaking load is what the part withstood in test, several times its WLL, and it is never a working figure.
02Can Grade 30, 43 or 70 chain be used for lifting?
No. Proof coil (Grade 30), high test (Grade 43) and transport (Grade 70) chain are made for tie-down, towing and general duty. Overhead lifting with chain calls for alloy chain — Grade 80 or Grade 100 — with fittings of the same grade.
03Do the parts come with test certificates?
Yes. Each consignment ships with the manufacturer's test certificate. If your site needs more — third-party certification or witnessed proof testing — say so on the RFQ and we will confirm what we can arrange.
04How do I read an Indus lifting part number?
IH-LR, then the family code, then the size. Inch sizes are written in hundredths of an inch (075 is 3/4″, 025X200 is 1/4″ × 2″), metric sizes in millimetres (10MM, M16), and capacities in tonnes (0T5 is 0.5 t). A trailing -C or -A marks the carbon-steel and alloy-steel versions of the same hook or link.
05How often must lifting equipment be thoroughly examined in the UAE?
It depends on the emirate and on whether the item is lifting equipment or a lifting accessory. In Abu Dhabi, Code of Practice 34.0 requires a thorough examination of lifting equipment every 12 months, and of lifting accessories and equipment for lifting people every 6 months, by a QCC-approved third party. In Dubai, Municipality guideline GU48 requires certification every 12 months by an EIAC-accredited third party, and EIAC's own requirements set 6-month intervals for accessories, manual equipment and people-lifting equipment. Daily and pre-use checks by the user apply everywhere, and an accessory without a legible WLL marking comes out of service.
06How much does the sling angle reduce what each leg can carry?
The flatter the sling, the more load each leg carries. Measured from the horizontal, a leg at 90° carries its share of the load; at 60° it carries about 1.15 times that share, at 45° about 1.41 times and at 30° twice as much. Most lifting standards do not allow angles flatter than 30° from horizontal. Size every component — sling, shackle, master link and lifting point — for the tension in the worst-loaded leg, not for the weight of the load divided by the number of legs.
07Grade 80 or Grade 100 alloy chain — which should I choose?
Both are alloy lifting chain rated at a 4:1 design factor. Grade 100 carries about 25% more working load than Grade 80 of the same size, so a smaller, lighter sling does the same lift. Grade 80 is the more widely used and stocked, and manufacturers generally allow it at higher service temperatures than Grade 100 — check the derating table for hot work. Whichever grade you choose, the fittings must be rated for it: a Grade 80 fitting sets the capacity of a Grade 100 sling.
08Can I send a full rigging list for one quotation?
Yes. Send the list with the WLL, size, quantity and any certification each line needs, and we quote it line by line under IH-LR part numbers, with the manufacturer's rating against each item. Where a manufacturer does not publish a WLL for a part, or a line is ambiguous — a shackle pattern, a chain grade or a sling length — we say so on the quotation rather than guess.