Galvanized Staple on Plate — 6 mm

Galvanized Staple on Plate, in 1 size, 6 mm. Load rating on request. Indus part numbers.
Key features
- Product type: Galvanized Staple on Plate
- Size range: 6 mm
- Size range
- 6 mm
- Material
- Carbon steel
- Finish
- Hot dipped galvanized
Product description
Lifting points, pad eyes and weld-on rings give a fixed or swivelling point to rig a load from. Carbon steel, hot dipped galvanized.
Sizes
1 size, 6 mm. Every size has its own Indus part number in the table below.
No load rating is published for this range. Tell us the duty and we will confirm the rating with the quotation. Do not use it to lift until you have that rating in writing.
The lettered dimensions in the table refer to the dimension drawing shown with this product.
Manufacturer's data
- Machining / welding.
Choosing a size
Rate the point for the load and the direction of pull. Bolted points need the stated thread engagement and torque; weld-on points need a qualified weld to sound structure.
Ordering
Quote the Indus part number from the size table, or send the size and rating you need.
Identification
| Parameter | Value |
|---|---|
| Product type | Galvanized Staple on Plate |
| Sizes | 1 |
Dimensions
| Parameter | Value |
|---|---|
| Size range | 6 mm |
Construction
| Parameter | Value |
|---|---|
| Material | Carbon steel |
| Finish | Hot dipped galvanized |
Shipping & lead time
Sizes & part numbers
1 size- Indus part no.IH-LR-LP-GSP-6MM
- Size
- 6 mm
- A (mm)
- 6
- B (mm)
- 15
- C (mm)
- 15
- E (mm)
- 35
- F (mm)
- 50
- d (mm)
- 6
Size — Nominal size as the manufacturer states it. A — Dimension A on the manufacturer dimension drawing. B — Dimension B on the manufacturer dimension drawing. C — Dimension C on the manufacturer dimension drawing. E — Dimension E on the manufacturer dimension drawing. F — Dimension F on the manufacturer dimension drawing. d — Dimension d on the manufacturer dimension drawing. Ask us for the dimension drawing if you need it stamped.
WLL is the most the part may carry in service. Proof and breaking loads are test figures — never lift to them. Each load is shown in the unit the manufacturer rates the part in, and a size ships with the manufacturer’s test certificate.
What is the Galvanized Staple on Plate and what is it used for?▾
How are the Indus part numbers for the Galvanized Staple on Plate structured?▾
What sizes does the Galvanized Staple on Plate come in?▾
How do I choose the right size of Galvanized Staple on Plate?▾
What is the working load limit of the Galvanized Staple on Plate?▾
What is the Galvanized Staple on Plate made from?▾
Does the Galvanized Staple on Plate come with a test certificate?▾
What should the Galvanized Staple on Plate be used with?▾
How should the Galvanized Staple on Plate be inspected and used safely?▾
Where is the Galvanized Staple on Plate typically used?▾
How does the Galvanized Staple on Plate differ from the Galvanized Ring on Plate?▾
Do you stock the Galvanized Staple on Plate in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog
Written about this range
Lifting & rigging
Lifting points compared: weld-on pad eyes, bolt-on and swivel lifting points, and eye bolts
A weld-on lifting point is only as good as its weld. A bolt-on point is only as good as its thread engagement and torque. A swivel point turns to face the sling, but not every one keeps its full rating sideways. Here is how the four kinds of lifting point compare, and what each needs to be fitted properly.
6 min read
Lifting & rigging
Precast concrete lifting clutches: how spherical-head anchor systems work, and how to use them safely
A lifting clutch hooks onto the spherical head of an anchor cast into a precast unit, and is released by hand once the unit is set down. The system is only as safe as its weakest decision: the anchor’s load class, the concrete’s strength at lifting, and the angle of pull. Here is how the system works and the rules makers set.
5 min read
Lifting & rigging
Eye bolt types and angled loads: plain, shoulder and DIN 580 collar eye bolts
A plain eye bolt is rated for a straight pull only. A shoulder eye bolt pulled at 45° keeps 30% of its rating. A DIN 580 collar eye bolt has its own table for angled loads and none at all for a pull across the eye. Here is how each type is rated, fitted and derated.
8 min read








