Skip to content

Lifting & Rigging

801 SKUs

Showing 385–432 of 801 SKUs

Yellow Grade 80 US-type connecting link (Hammerlok style), beside its drawing

Grade 80 Connecting Link — US Type, 3,500–72,300 lbs WLL

7 mm (9/32″ (1/4″)) to 32 mm (1-1/4″)3,500 to 72,300 lbs
Inquire
Yellow Grade 80 clevis sling hook, beside its dimension drawing

Grade 80 Clevis Sling Hook — 3,500–18,100 lbs WLL

Alloy steel (Grade 80)3,500 to 18,100 lbs
Inquire
Yellow Grade 80 clevis grab hook with clevis pin

Grade 80 Clevis Grab Hook — 3,500–28,300 lbs WLL

3,500 to 28,300 lbsAlloy steel (Grade 80)
Inquire
Grade 70 Chain — AS/NZS 4344 — dimension drawing

Grade 70 Chain — AS/NZS 4344, 6–13 mm

Yellow or white zinc chromate finish6 mm to 13 mm
Inquire
Grade 30 Long Link Chain, Inch Sizes

Grade 30 Long Link Chain — Inch Sizes, 1,300–2,650 lbs WLL

Self-colour, electro-galvanized or hot-dip galvanized1,300 to 2,650 lbs
Inquire
Grade 100 two-leg chain sling with grab hooks, type DOG

Grade 100 Two-Leg Chain Sling with Grab Hooks — Type DOG, 2–37.5 t WLL

2 to 37.5 t, legs up to 45° from vertical6 mm to 26 mm chain
Inquire
Grade 100 three-leg chain sling with grab hooks, type TOG

Grade 100 Three-Leg Chain Sling with Grab Hooks — Type TOG, 3–56 t WLL

6 mm to 26 mm chainGrade 100 alloy steel chain and fittings, quenched and tempered
Inquire

Questions we get asked

About this range

01What is the difference between WLL, SWL and breaking load?
WLL — working load limit — is the most the manufacturer rates a part to carry in service. SWL, safe working load, is the older term and is sometimes set lower for a particular installation. The minimum breaking load is what the part withstood in test, several times its WLL, and it is never a working figure.
02Can Grade 30, 43 or 70 chain be used for lifting?
No. Proof coil (Grade 30), high test (Grade 43) and transport (Grade 70) chain are made for tie-down, towing and general duty. Overhead lifting with chain calls for alloy chain — Grade 80 or Grade 100 — with fittings of the same grade.
03Do the parts come with test certificates?
Yes. Each consignment ships with the manufacturer's test certificate. If your site needs more — third-party certification or witnessed proof testing — say so on the RFQ and we will confirm what we can arrange.
04How do I read an Indus lifting part number?
IH-LR, then the family code, then the size. Inch sizes are written in hundredths of an inch (075 is 3/4″, 025X200 is 1/4″ × 2″), metric sizes in millimetres (10MM, M16), and capacities in tonnes (0T5 is 0.5 t). A trailing -C or -A marks the carbon-steel and alloy-steel versions of the same hook or link.
05How often must lifting equipment be thoroughly examined in the UAE?
It depends on the emirate and on whether the item is lifting equipment or a lifting accessory. In Abu Dhabi, Code of Practice 34.0 requires a thorough examination of lifting equipment every 12 months, and of lifting accessories and equipment for lifting people every 6 months, by a QCC-approved third party. In Dubai, Municipality guideline GU48 requires certification every 12 months by an EIAC-accredited third party, and EIAC's own requirements set 6-month intervals for accessories, manual equipment and people-lifting equipment. Daily and pre-use checks by the user apply everywhere, and an accessory without a legible WLL marking comes out of service.
06How much does the sling angle reduce what each leg can carry?
The flatter the sling, the more load each leg carries. Measured from the horizontal, a leg at 90° carries its share of the load; at 60° it carries about 1.15 times that share, at 45° about 1.41 times and at 30° twice as much. Most lifting standards do not allow angles flatter than 30° from horizontal. Size every component — sling, shackle, master link and lifting point — for the tension in the worst-loaded leg, not for the weight of the load divided by the number of legs.
07Grade 80 or Grade 100 alloy chain — which should I choose?
Both are alloy lifting chain rated at a 4:1 design factor. Grade 100 carries about 25% more working load than Grade 80 of the same size, so a smaller, lighter sling does the same lift. Grade 80 is the more widely used and stocked, and manufacturers generally allow it at higher service temperatures than Grade 100 — check the derating table for hot work. Whichever grade you choose, the fittings must be rated for it: a Grade 80 fitting sets the capacity of a Grade 100 sling.
08Can I send a full rigging list for one quotation?
Yes. Send the list with the WLL, size, quantity and any certification each line needs, and we quote it line by line under IH-LR part numbers, with the manufacturer's rating against each item. Where a manufacturer does not publish a WLL for a part, or a line is ambiguous — a shackle pattern, a chain grade or a sling length — we say so on the quotation rather than guess.