The 37° flare is the most widely used hydraulic connection on inch-thread machines — American and much Asian equipment, and almost every hose assembly sold with a JIC end. Most of the adapters in a workshop drawer are JIC on at least one end. This guide is about choosing and ordering them: the shapes in the range, how they are rated, and how to describe one so the right part comes back. For how JIC compares with ORFS, NPT and BSP, see the four connector families.
/01The shapes.
| Shape | What it does | Watch for |
|---|---|---|
| Straight connectorHighlighted | JIC male to a port thread (ORB, NPT, BSPP, BSPT, metric) | The port end decides the seal |
| Union | JIC male both ends — joins two JIC female hoses or nuts | Same dash both ends unless a reducer |
| 90° / 45° elbow | Turns the line at the port | Adjustable or fixed port end |
| Tee (run / branch) and cross | Splits a line; run tee has the port in line, branch tee at 90° | Which leg is the port |
| Bulkhead union / elbow | Passes through a panel, held by a lock nut | Panel thickness and hole size |
| Female swivel connector | JIC female nut on one end — connects to a male JIC without twisting | Nut seats on the mating cone |
| Reducer / expander | Changes dash size within JIC | One step at a time; avoid stacking |
| Cap and plug | Close a male or female JIC end | Cap fits a male, plug a female |
Two terms cause most ordering errors. A run tee has the port end in line with one run of the tee; a branch tee has it on the side branch. And on shaped fittings with an O-ring boss port, the port end is either adjustable — with a locknut and back-up washer, so the elbow can be turned to face the line before it is locked — or fixed. Parker puts adjustable ends on shaped fittings for orientation and fixed ends on straights.
/02Sizes and threads.
| Dash | Tube / hose | Thread | Dash | Tube / hose | Thread |
|---|---|---|---|---|---|
| -2 | 1/8" | 5/16-24 | -12 | 3/4" | 1 1/16-12 |
| -3 | 3/16" | 3/8-24 | -14 | 7/8" | 1 3/16-12 |
| -4Highlighted | 1/4" | 7/16-20 | -16 | 1" | 1 5/16-12 |
| -5 | 5/16" | 1/2-20 | -20 | 1 1/4" | 1 5/8-12 |
| -6 | 3/8" | 9/16-18 | -24 | 1 1/2" | 1 7/8-12 |
| -8 | 1/2" | 3/4-16 | -32 | 2" | 2 1/2-12 |
| -10 | 5/8" | 7/8-14 | -40 | 2 1/2" | 3-12 |
The dash number is the tube OD in sixteenths of an inch. The JIC thread is a UN/UNF straight thread that only holds the nut; it does not seal. Note that an ORB port of the same dash shares the same thread size — a -8 ORB port is also 3/4-16 — which is why a JIC × ORB adapter is often the same thread on both ends with different seals. Need the full reference? See thread size and pitch by family.
/03Ratings: size, shape and the other end.
| Dash | 37° × ORB straight | 37° elbow | 37° × NPTF straight |
|---|---|---|---|
| -4Highlighted | 7,500 | — | 6,000 |
| -6 | 6,000 | — | — |
| -8 | 6,000 | 6,000 | — |
| -10 | 5,000 | — | — |
| -12 | 5,000 | — | — |
| -16Highlighted | 4,500 | 4,000 | 3,000 |
| -20 | 4,000 | — | — |
| -24 | 3,000 | — | — |
| -32 | 2,000 | — | — |
Three rules come out of that table. The rating falls as the size rises. Shaped fittings rate at or below straights. And the weaker end wins — a pipe-thread end caps the adapter below what the 37° end could take (see NPT and NPSM adapters). These are one maker’s figures; our listings quote the rating published for each family, and a hose or tube assembly is rated to its weakest part. In salt-laden air, Parker reports its zinc-plated steel 37° fittings well past the SAE requirement of 96 hours to red rust in ASTM B117 — useful, but not a substitute for stainless JIC on deck or splash zones.
/04Making them up.
| Dash | Torque | FFWR, tube | FFWR, swivel/hose |
|---|---|---|---|
| -4 | 13 ft-lb | 2½ | 2 |
| -6 | 22 ft-lb | 2 | 1½ |
| -8Highlighted | 42 ft-lb | 2 | 1½ |
| -10 | 60 ft-lb | 1½ | 1½ |
| -12 | 84 ft-lb | 1½ | 1¼ |
| -16 | 118 ft-lb | 1½ | 1 |
| -20 | 168 ft-lb | 1 | 1 |
| -32 | 265 ft-lb | 1 | 1 |
Torque values are for unlubricated steel. Flats from wrench resistance — snug the nut, then turn it a counted number of hex flats — is the check when a torque wrench will not fit. Over-tightening a 37° joint cracks flares and coins the cone; see make-up torque and turns and reading an over-tightened joint. For tube to be flared, Parker specifies fully annealed C-1010 steel tube to HRB 72 (or C-1021 to HRB 75).
/05How to order.
| Item | Example |
|---|---|
| Shape | 90° elbow, adjustable |
| End 1 — type, gender, dash | JIC 37° male, -8 |
| End 2 — type, gender, sizeHighlighted | ORB male, -8 (3/4-16) |
| End 3 (tees) | and which leg is the port: run or branch |
| Material | Zinc-plated steel, or 316 stainless |
| Quantity | And whether caps or plugs are needed for shipping |
Common questions
- What is a JIC adapter?
- An adapter with at least one 37° flare (JIC, SAE J514) end, joining a JIC hose or tube to a port or another fitting. It seals metal to metal on the 37° cone.
- What does -8 mean on a JIC fitting?
- Dash 8 — 8/16 = 1/2" tube or hose — with a 3/4-16 UNF thread.
- What is the difference between a run tee and a branch tee?
- Where the odd end is. On a run tee the port or swivel end is in line with the run; on a branch tee it is on the side branch.
- What pressure is a JIC adapter rated for?
- It depends on size, shape and the other end. Parker’s steel 37° × ORB straights run from 7,500 psi at -4 to 2,000 psi at -32; elbows and pipe-thread ends rate lower.
- Can I mix JIC with 45° SAE flare fittings?
- No. 45° flare fittings (SAE J512, refrigeration and fuel) share some thread sizes with JIC but the seat angles differ and the joint will leak.
- Should I order adjustable or fixed elbows?
- Adjustable where the elbow must be aimed at a line — it has a locknut and washer on the ORB end. Fixed for straights or where orientation does not matter.
What we list
Every steel JIC 37° adapter in the range, including the Tompkins-made parts:
- Lock Nut JIC
- Male Cross JIC
- Run Tee Swivel JIC
- Male Tee JIC
- Branch Tee Swivel Connector JIC
- Adjustable Branch Tee m JIC X m NPT X m JIC
- Adjustable Branch Tee m JIC X m SAE X m JIC
- Adjustable Run Tee m JIC X m JIC X m Metric
- Adjustable Run Tee m JIC X m JIC X m BSP
- 90° Male Female Connector m JIC X f JIC
- Male Female Connector m JIC X f JIC
- Plug JIC
- Swivel Cap JIC
- 45° Female Swivel Connector JIC
- Swivel Connector f JIC x f JIC
- 45° Swivel Connector m JIC X f JIC
- 90° Elbow m JIC X m BSPT
- Bulkhead Union JIC
- Male Connector m JIC X m BSPT
- 45° Elbow m JIC X m BSPT
- Male Connector m JIC X m NPT
- 90° Elbow Connector m JIC X m NPT
- Adjustable 90° Elbow m JIC X m Metric Flat
- Male Connector m JIC X m Metric
- Male Connector m JIC X m Metric Flat with Seal
- Adjustable 45° Elbow m JIC X m Metric Flat
- Adjustable 90° Elbow m JIC X m SAE
- Adjustable 90° Elbow m JIC X m BSP
- Adjustable 45° Elbow m JIC X m SAE
- Male Connector m JIC X m SAE
- Male Connector JIC
- 90° Elbow Connector m JIC
- 90° Elbow JIC Male 74° Cone Bulkhead
- 45° JIC Male 74° Cone
- 45° Elbow JIC Male 74° Cone Bulkhead
- 45° Elbow JIC Male 74° Cone × NPT Male
- JIC Male 74° Cone × BSP Male Captive Seal
- JIC Male 74° Cone × BSP Male O-Ring
- 45° JIC Male 74° Cone × BSP Male O-Ring Adjustable Stud End
- Metric Thread Male Captive Seal × JIC Female 74° Seat
- BSPT Male × JIC Female 74° Seat
- Metric Male × JIC Female 74° Seat
- SAE O-Ring Boss × JIC Female 74° Seat
- JIC Male 74° Cone Bulkhead Branch Tee
- JIC Male 74° Cone Bulkhead Branch Tee (AJJ6J)
- JIC Male 74° Cone × SAE O-Ring Boss Run Tee
- Steel JIC 37° Male × NPTF Female Connector
- Steel JIC 37° Male × NPTF Female 90° Elbow
- Steel JIC 37° Male × NPTF Female 45° Elbow
- Steel JIC 37° Male × NPTF Female Branch Tee
- Steel JIC 37° Male × NPTF Male Run Tee
- Steel JIC 37° Male × NPTF Female Run Tee
- Steel JIC 37° Male × NPTF Male Service Tee
- Steel JIC 37° Male × NPTF Male × NPTF Female Service Tee
- Steel JIC 37° Male Bulkhead Run Tee
- Steel NPTF Female × JIC 37° Male Bulkhead Connector
- Steel NPTF Male × JIC 37° Male Bulkhead Connector
- Steel JIC 37° Short Flare Nut
- Steel JIC 37° Long Flare Nut
- Steel JIC 37° Tube Nut
- Steel JIC 37° Tube Sleeve
- Steel Convert-A-Flare Tube Nut, JIC 37° to Flareless
- Steel Convert-A-Flare Tube Sleeve, JIC 37° to Flareless
- Steel NPTF Male × JIC 37° Female Swivel 90° Elbow
- Steel NPTF Female × JIC 37° Female Swivel 90° Elbow
- Steel NPTF Male × JIC 37° Female Swivel Connector
- Steel NPTF Female × JIC 37° Female Swivel Connector
- Steel JIC 37° Sleeve for Metric Tube
- Tompkins 0304 JIC 37° Female Cap
- Tompkins 0306 JIC 37° Bulkhead Locknut
- Tompkins 0418 JIC 37° No-Flare Tube Nut
- Tompkins 0419 JIC 37° No-Flare Tube Sleeve
- Tompkins 2404-L Male JIC 37° × Male NPTF Connector, Long
- Tompkins 2404-LL Male JIC 37° × Male NPTF Connector, Extra Long
- Tompkins 2501-L Male JIC 37° × Male NPTF 90° Elbow, Long
- Tompkins 2501-LL Male JIC 37° × Male NPTF 90° Elbow, Extra Long
- Tompkins 2501-LLL Male JIC 37° × Male NPTF 90° Elbow, Extra-Extra Long
- Tompkins 2501-S Male JIC 37° × Male NPTF Swivel 90° Elbow
- Tompkins 6400-L Male JIC 37° × Male O-Ring Boss Connector, Long
- Tompkins 6510 Female JIC 37° Swivel × Female JIC 37° Swivel Union
- Tompkins 6606 Female JIC 37° Swivel Run Tee
- Tompkins 6801-L Male JIC 37° × Male O-Ring Boss Adjustable 90° Elbow, Long
- Tompkins 6801-LL Male JIC 37° × Male O-Ring Boss Adjustable 90° Elbow, Extra Long
- Tompkins 6801-LLL Male JIC 37° × Male O-Ring Boss Adjustable 90° Elbow, Extra-Extra Long
- Tompkins 6801-S Male JIC 37° × Male O-Ring Boss Swivel Adjustable 90° Elbow
JIC adapters
IH-AD-JIC-026Male JIC 37° × Male NPT AdapterIndus Hydraulics
IH-AD-JIC-032Male JIC 37° × Male SAE ORB Adjustable 90° Elbow AdapterIndus Hydraulics
IH-AD-JIC-013Male JIC 37° × Female JIC 37° AdapterIndus Hydraulics
IH-AD-JIC-023Bulkhead Union JICIndus Hydraulics
IH-AD-JIC-005Male Tee JICIndus Hydraulics
IH-ST-6505Steel NPTF Male × JIC 37° Female Swivel ConnectorIndus Hydraulics
IH-TK-6801-LTompkins 6801-L Male JIC 37° × Male O-Ring Boss Adjustable 90° Elbow, LongTompkins
IH-ST-319Steel JIC 37° Tube SleeveIndus Hydraulics
Sources
- 1.Parker Hannifin Tube Fittings Division. Catalog 4300 (2017 edition; current edition 9/2023). ↗




