Skip to content
Buying fittings & adapters

ORFS and ORB adapters: O-ring face seal and O-ring boss — ratings, torque, sleeves and O-rings

Most hydraulic leaks that come back after re-tightening are metal seats that never sealed. ORFS and ORB move the seal to an O-ring — and that makes the O-ring the part to stock. The steel ORFS and ORB range: unions, elbows, tees, bulkheads, swivels, adjustable elbows, braze and mechanical sleeves, plugs and O-ring kits, with Parker’s ratings (9,200 psi in the small sizes) and torque by dash size.

Written by
Ayush Bhatia, Director
Published
Updated
Reading
8 min · 3 sections
Share
Zinc-plated steel ORFS adapters with face O-rings, ORB adapters, an adjustable elbow and a box of assorted O-rings
Two O-ring seals and a box of spares: the O-ring is the part that wears.

At a glance

Key takeaways

  1. ORFS (SAE J1453 / ISO 8434-3) seals on an O-ring held in a groove in the male face; ORB (SAE J1926 / ISO 11926) seals on an O-ring under the adapter shoulder in a straight-thread port.
  2. Parker rates its steel ORFS × ORB connectors at 9,200 psi for -4 to -8, 6,000 psi for -10 to -20, 5,000 psi at -24 and 3,000 psi at -32.
  3. ORFS is made up by torque — Parker gives 18 ft-lb at -4, 40 at -8, 110 at -16 — and requires the joint to survive 200% of rated torque.
  4. On the tube side ORFS needs a sleeve: brazed onto the tube, or a mechanical sleeve for tube flanged to 90°.
  5. The O-ring is the wear part: standard is 90-durometer nitrile; FKM for heat and fluids nitrile dislikes. Keep a kit.

Figures verified · Ratings, threads, torque and O-ring defaults from Parker Catalog 4300 (2017 edition — check the current edition before quoting a figure).

ORFS and ORB are the two O-ring connections of inch hydraulics, and most modern North American and Asian machines use both: ORFS on hose and tube ends, ORB on valve, pump and cylinder ports. Because the seal is an elastomer, both tolerate vibration and pressure spikes that loosen a metal seat — and both fail when the O-ring is wrong, cut or missing. This guide covers the steel adapter range, how it is rated and made up, and the O-rings to stock with it.

/01How each seals.

ORFS is a nut, a body, an O-ring and a sleeve. The O-ring sits in a captive groove in the flat face of the male body; the nut draws a flat sleeve face onto it. Parker describes the design as leak-free. On tube the sleeve is either brazed on, or a mechanical sleeve is used with the tube end flanged to 90°.

ORB is a port, not a tube end: a UN/UNF straight thread with an O-ring that is squeezed into a chamfer at the top of the port by the adapter’s shoulder. The thread holds; the O-ring seals. Parker recommends ORB, four-bolt flanges or ISO 6149 ports over tapered pipe threads.

Parker steel ORFS × ORB connector ratings, and ORFS nut thread and torque
DashTube ODWorking pressureORFS nut threadORFS torque
-41/4"9,200 psi9/16-1818 ft-lb (25 N·m)
-63/8"9,200 psi11/16-1630 ft-lb (40 N·m)
-8Highlighted1/2"9,200 psi13/16-1640 ft-lb (55 N·m)
-105/8"6,000 psi1-1460 ft-lb (80 N·m)
-123/4"6,000 psi1 3/16-1285 ft-lb (115 N·m)
-16Highlighted1"6,000 psi1 7/16-12110 ft-lb (150 N·m)
-201 1/4"6,000 psi1 11/16-12150 ft-lb (205 N·m)
-241 1/2"5,000 psi2-12230 ft-lb (315 N·m)
-322"3,000 psi2 1/2-12375 ft-lb (510 N·m)

ORFS nut threads are not JIC threads of the same dash — a -8 ORFS nut is 13/16-16, a -8 JIC nut 3/4-16 — so the two families cannot be screwed together by mistake. The ORB port thread, by contrast, follows the tube dash (-4 7/16-20, -8 3/4-16, -16 1 5/16-12), the same as the JIC thread of that dash. Parker notes that straight-thread O-ring ports hold 6,000 psi and more up to size 12 (M27), and lose capability above it.

/02The range.

  • Straight connectors: ORFS male to ORB, NPT, BSPP, metric flat-face or JIC.
  • Unions, elbows, tees, crosses and bulkheads with ORFS male ends, and bulkhead locknuts.
  • Swivels: ORFS female swivel nuts on elbows and connectors, joining to an ORFS male without twisting the line.
  • Adjustable elbows and tees with an ORB, BSP or metric stud, a locknut and back-up washer, so the fitting can be aimed before it is locked.
  • Sleeves and nuts: braze sleeves, mechanical sleeves and tube nuts for tube work.
  • ORB adapters: ORB × NPTF, ORB × ORB reducers and unions, ORB elbows to NPTF, JIC and NPSM swivel ends, and hex, hollow-hex and socket plugs.
  • O-rings: NBR and FKM rings for ORB ports and ORFS faces, and an assortment kit.

/03O-rings: the part that wears.

An ORFS or ORB joint is only as good as its O-ring. Parker’s standard ring in SAE fittings is 90-durometer nitrile (Buna-N); it calls for 90-durometer rings at 1,500 psi and above, and offers fluorocarbon (FKM, Viton) as the option for heat and for fluids nitrile does not tolerate. Replace the O-ring every time a joint is opened, check it is the face-seal size for ORFS and the boss size for ORB — they are not the same ring — and keep it clean and lightly lubricated with system fluid on assembly. A cut or pinched O-ring is the usual cause of a new ORFS joint that leaks; see reading a weeping joint.

Parker standard O-ring sizes: ORB port (SAE J1926) and ORFS face
DashORB threadORB O-ringORFS O-ring
-47/16-203-9042-011
-69/16-183-9062-012
-8Highlighted3/4-163-9082-014
-107/8-143-9102-016
-121 1/16-123-9122-018
-16Highlighted1 5/16-123-9162-021
-201 5/8-123-9202-025
-241 7/8-123-9242-029
-322 1/2-123-9322-135

Two patterns make these easy to remember: the ORB ring number is 3-9 followed by the dash size, and every ORFS face ring is 0.070" (1.78 mm) section except -32 at 0.10" (2.54 mm). Parker also offers a 75-durometer nitrile for CNG service.

Which O-ring?

  1. IfMineral hydraulic oil, normal temperature?

    90-durometer nitrile (NBR) — the standard ring.

    IH-ST-OFS1
  2. IfHot oil, synthetic or fire-resistant fluid that attacks nitrile?

    FKM (Viton).

    IH-ST-OFS2
  3. IfORB port rather than an ORFS face?

    The ORB boss ring for that dash, NBR or FKM.

    IH-ST-OB1
  4. IfWorkshop or field service stock?

    An assortment kit covering the common sizes.

    IH-ST-30002

Common questions

What is the difference between ORFS and ORB?
ORFS is a tube or hose end that seals on an O-ring in a flat face (SAE J1453). ORB is a port that seals on an O-ring under the adapter shoulder (SAE J1926). Many adapters have one of each.
What pressure are ORFS adapters rated for?
In Parker’s steel tables, ORFS × ORB connectors are 9,200 psi for -4 to -8, 6,000 psi for -10 to -20, 5,000 psi at -24 and 3,000 psi at -32.
What torque for ORFS fittings?
Parker: -4 18 ft-lb, -6 30, -8 40, -10 60, -12 85, -16 110, -20 150, -24 230, -32 375 ft-lb. Torque is the preferred method.
Can I reuse ORFS O-rings?
Replace the O-ring whenever the joint is opened; it is inexpensive and the usual cause of a leak on reassembly.
Do ORFS and JIC fittings screw together?
No. The nut threads differ for the same dash size, so they do not mate. Use an ORFS × JIC adapter.
What is a braze sleeve?
An ORFS sleeve brazed onto plain tube to give it the flat sealing face. A mechanical sleeve is the alternative for tube flanged to 90°.

What we list

Steel ORFS and ORB adapters, sleeves and nuts — including Tompkins-made parts — and O-rings:

ORFS and ORB adapters

Sources

  1. 1.Parker Hannifin Tube Fittings Division. Catalog 4300 (2017 edition; current edition 9/2023). ↗
MarketSupplying Jordan from DubaiFreight, import documents and lead times for mining and processing operations in Jordan.MarketSupplying Czechia from DubaiFreight, import documents and lead times for steel and metals plants in Czechia.

What next

  1. 01
  2. 02
  3. 03

    Where these orders go

    Fittings and adapters are the smallest thing we ship and the one that decides whether a machine works, so they travel the way the destination allows: consolidated into a planned consignment where a site is on a long lane, and on their own airway bill when something is standing still. Orders of this kind are quoted from a photograph and a measurement rather than a part number, which is what makes them practical to place from somewhere with no counter nearby.

    Everything above ships from the same Dubai warehouse. If your destination is not listed, it is almost certainly still one we quote. See every export destination

Ordering ORFS or ORB adapters?

Send the shape, both ends and dash sizes, and the fluid. We will quote the adapters with the right O-ring compound and spare rings.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Buying fittings & adapters

All articles in this topic
Plastic push-to-connect pneumatic fittings with blue and black polyurethane air tubes on a machine manifold

Push-to-connect air fittings: how they grip and seal, ratings, tube, and the mistakes that make them leak

4 min read

Brass 45° flare fittings, flared copper tube, compression fittings with sleeves, and an inverted flare union on steel tube

Brass flare and compression fittings: SAE 45° flare, inverted flare and compression — ratings and threads

5 min read

Brass threaded pipe fittings: hex nipple, street elbow, tee, coupling, union, hex bushing, square-head plug and cap

Brass pipe fittings and adapters: NPTF and BSP threads, 1,000 psi ratings, lead-free and DZR brass

5 min read

Back to Blog