Skip to content

Chain & Chain Fittings

135 SKUs

Showing 97–135 of 135 SKUs

Red Grade 100 clevis foundry hooks, wide throat and clevis pin, two views

Grade 100 Clevis Foundry Hook — 2.5–16 t WLL

Alloy steel, quenched and temperedPowder coated
Inquire
Stainless Steel Hammerlock — European Type — dimension drawing

Stainless Steel Hammerlock — European Type

Stainless steel 304 or 316 connectorPolished
Inquire
Toothed wheel (sprocket) for DIN 764 chain, six teeth and keyed bore

Toothed Wheel for DIN 764 Chain

Cast or forged steel, teeth hardened10 × 35 mm to 18 × 63 mm chain
Inquire
Segmented plain wheel for bucket elevator chain, bolted rim segments on a four-arm hub

Segmented Plain Wheel for Bucket Elevator Chain

Ø 450 mm to Ø 800 mmSteel; replaceable hardened rim segments
Inquire
Segmented plain rim wheel for bucket elevator chain, bolted wear segments on a spoked hub

Segmented Plain Rim Wheel for Bucket Elevator Chain

Steel; replaceable hardened rim segments in pairsØ 630 mm to Ø 1250 mm
Inquire
Round Link Mining Chain, DIN 22252

Round Link Mining Chain — DIN 22252

Alloy steel (e.g. 23MnNiCrMo54), quenched and tempered14 × 50 mm to 42 × 146 mm
Inquire
Red pocket wheel (chain sprocket) for DIN 764 round link chain

Pocket Wheel for DIN 764 Chain

Cast or forged steel, pockets hardened10 × 35 mm to 23 × 80 mm chain
Inquire
One-piece cast plain wheel for bucket elevator chain, spoked with central hub

One-Piece Plain Wheel for Bucket Elevator Chain

MachinedSteel, wear surface hardened
Inquire
Flat Link Mining Chain, DIN 22255

Flat Link Mining Chain — DIN 22255

26 × 92 mm to 42 × 146 mmAlloy steel, quenched and tempered
Inquire
Block Connecting Link for Mining Chain, DIN 22258-1 — dimension drawing

Block Connecting Link for Mining Chain — DIN 22258-1

Forged alloy steel, heat treatedSelf-colour or painted
Inquire
DIN 5683 Long Link Chain — dimension drawing

DIN 5683 Long Link Chain

Zinc plated/selfcolor/hot dipped galvanizedAlloy steel 20MnSi
Inquire
Short Link Chain, UK Pattern

Short Link Chain — UK Pattern

1/8″ (3.2 mm) to 1″ (25.4 mm)Self-colour, black or hot-dip galvanized
Inquire
Medium Link Chain, UK Pattern

Medium Link Chain — UK Pattern

Load rating on requestSelf-colour, black or hot-dip galvanized
Inquire
Long Link Chain, UK Pattern

Long Link Chain — UK Pattern

Load rating on requestSelf-colour, black or hot-dip galvanized
Inquire

Questions we get asked

About this range

01Can Grade 30, 43 or 70 chain be used for lifting?
No. Proof coil (Grade 30), high test (Grade 43) and transport (Grade 70) chain are made for tie-down, towing and general duty. Overhead lifting with chain calls for alloy chain — Grade 80 or Grade 100 — with fittings of the same grade.
02Can I mix Grade 80 chain with Grade 100 fittings?
A chain sling is rated by its weakest component, so a mixed assembly takes the lower grade's rating. Match the fittings to the chain grade and size.
03Do the parts come with test certificates?
Yes. Each consignment ships with the manufacturer's test certificate. If your site needs more — third-party certification or witnessed proof testing — say so on the RFQ and we will confirm what we can arrange.
04What is the difference between EN 818-2 and EN 818-7 chain?
EN 818-2 is medium-tolerance Grade 8 chain for chain slings, and EN 818-7 is fine-tolerance chain made to run over the pocketed load sheave of a hoist. Hoist chain is calibrated so each link seats in the pocket, and it is specified by the hoist maker for that block. Sling chain does not have that pitch accuracy and must never be fitted to a hoist; hoist chain is not normally used to make up slings either. Order hoist chain by the hoist make and model as well as size.
05How can I tell what grade a lifting chain is?
Alloy lifting chain is embossed at intervals along its length with a grade mark and the manufacturer's identification, and the fittings carry their own grade and size marks. Grade 80 chain is typically marked 8 or 80 and Grade 100 chain 10 or 100. If a chain carries no legible grade mark and no certificate traces it, treat it as unrated and keep it out of lifting service. Plain or galvanized chain with no mark is usually general-purpose chain.
06When should alloy lifting chain be taken out of service?
Take it out of service when any link is worn, stretched, bent, nicked, cracked or heat-damaged beyond the manufacturer's limits, or when its grade and size marks can no longer be read. Manufacturers commonly set the wear limit at 10% loss of the link's nominal diameter, measured as the mean of two diameters at right angles. Any visible stretch, a link that no longer hinges freely, or weld spatter and heat discolouration are also reasons to remove it. The competent person's thorough examination is the deciding check.
07What types of lifting chain do you supply?
The range covers Grade 80 and Grade 100 alloy lifting chain and fittings, EN 818-7 hoist chain, stainless chain, DIN 763, 764 and 766 link chain and DIN 22252 mining chain. Grade 30, 43 and 70 chain is listed in inch and AS/NZS 4344 sizes.
08Which chain grades do you supply?
Grade 80 and Grade 100 alloy lifting chain, plus Grade 30, 43 and 70 chain in inch and AS/NZS 4344 sizes. Matching Grade 80 and Grade 100 chain fittings are listed separately.