Skip to content
Assembly, crimping & certification

Spiral hose crimp fittings: 4SP, 4SH, R12, R13 and R15 — interlock, skive, flange heads and crimping

Spiral hose is where the pressures are highest and the crimps hardest: Parker’s R15 hose is rated 6,000 psi in every size, and its skive fittings need 320 to 340 tons of crimping force. The spiral range — crimp fittings in every end form, Code 61 and 62 flange heads, Supercat flange-on fittings, split flanges and SAE flange hardware — with how interlock and skive fittings grip the wire, ratings by hose class, and how to crimp and check them.

Written by
Ayush Bhatia, Director
Published
Updated
Reading
9 min · 4 sections
Share
A heavy four-spiral hydraulic hose crimped to a flange-head fitting, beside a 90° flange fitting and a heavy ferrule
Spiral hose carries the highest pressures, and its fittings are built to match.

At a glance

Key takeaways

  1. Spiral hose (EN 856 4SP and 4SH, SAE 100R12, R13 and R15) carries the highest pressures, and its fittings grip the wire itself: Parker calls it Interlock — the reinforcement locked between shell and nipple.
  2. Two routes: no-skive interlock fittings, or skive fittings that need the cover and inner tube cut back; Parker’s ParLock skive fittings need 320–340 tons and an adjustable crimper.
  3. Ratings depend on the class: R13 is 5,000 psi and R15 6,000 psi at every size; 4SH falls from 6,000 psi at -12 to 3,600 psi at -32; R12 is 4,000 psi to -16.
  4. Large spiral hose usually ends in an SAE flange head: Code 61 (Parker’s 77 Series special head 5,000 psi) or Code 62 (6,000 psi) — ISO 12151-3 S-L and S-S.
  5. Do not lubricate spiral hose for assembly, skive in the direction of the spiral, and clean the hose after skiving.

Figures verified · Hose classes, ratings, interlock and skive rules from Parker Catalog 4400 (US and UK); Danfoss spiral fitting data; ISO 12151-3 scope.

Excavator booms, mining shovels, presses and drilling rigs run four- and six-spiral hose, because braided hose cannot carry 5,000–6,000 psi at an inch and above. The fittings that go on it are heavier, the crimps harder, and the rules stricter than for braided hose. This guide covers the spiral crimp range and how to assemble it; for the braided side see braided crimp fittings.

/01The spiral hose classes.

Spiral hose classes and Parker example ratings, psi
ClassParker hoseRatingParker fitting series
EN 856 4SP7016,500 (-6) to 4,000 (-16)70 (Europe)
EN 856 4SH7316,000 (-12) to 3,600 (-32)73 (Europe); ParLock V4 skive
SAE 100R127224,000 to -16; 3,000 at -20; 2,500 at -2471 / 43
SAE 100R13Highlighted7815,000 at every size78 (Europe)
SAE 100R15Highlighted791TC / 792TC / 792LT6,000 at every size79
ISO 18752 constant pressure387 / 487 / 787 / 7973,000 / 4,000 / 5,000 / 6,000, -4 to -3243 (small) / 77

The EN 856 classes fall with size; R13, R15 and ISO 18752 hoses hold one pressure across their range, which makes them easier to standardise on a machine. ISO 18752 also grades hose by impulse life: class AC and BC at 100 °C for 200,000 and 500,000 cycles, CC and DC at 120 °C for 500,000 and 1,000,000. For the names, see EN 853, 856 and 857 against SAE 100R.

/02Interlock and skive.

Parker describes fittings that lock the metal reinforcement of the hose directly between the metal shell and nipple as Interlock. It offers two routes. Interlock No-Skive fittings (its 77 Series on 787TC and 797TC) are designed to engage the inside of the tube into the spiral wire. ParLock skive fittings need the hose prepared: external skive only (VS) on smaller 4SP, or internal and external skive (V4, V6) on 4SH and larger R13- and R15-class hoses. Danfoss offers an internal-skive spiral fitting to 500 bar (7,250 psi), tested to two million flex-impulse cycles.

Parker’s skiving rules: distinguish internal (inner tube) from external (cover) skiving; always skive in the direction of the spiral layers; clean the hose immediately afterwards with projectiles. Two-piece skive fittings must not be crimped on Parkrimp crimpers — only on adjustable crimpers, with at least 320 tons for V4 and 340 tons for V6 — and Parker measures their conicity at both ends of the ferrule in two planes 90° apart. And for any spiral hose: do not lubricate it for assembly.

/03Flange heads and SAE flange hardware.

From about -12 up, spiral hose usually ends in an SAE four-bolt flange head clamped to the port. ISO 12151-3 covers hose fittings with ISO 6162 flange ends; Parker marks Code 61 heads "S-L" and Code 62 heads "S-S". On its European S6 Series a Code 61 head is rated 5,000 psi and a Code 62 head 6,000 psi; its US 77 Series offers a "Code 61 Special Flange Head" at 5,000 psi; its 76 Series uses 8,000 psi flange heads. Our range includes straight, 45°, 90° and long-drop Code 61 and 62 heads, "Supercat" flange-on fittings with the flange already fitted, split flange clamp pairs with bolts, and SAE flanges for the pipe side — threaded, socket-weld, butt-weld and blind — with O-rings and bolt sets. See SAE flange adapters.

/04Routing spiral hose.

Parker defines minimum bend radius as the smallest arc a hose can be bent to before its life is greatly reduced — beyond it, kinking, tube washout and overstressed reinforcement follow — and warns against sharp bending at the hose-to-fitting juncture and against installations that twist the hose. Spiral hose is stiff, so elbow heads and long-drop elbows earn their place: they let the hose leave the port in the direction it must go without a bend at the ferrule. When an assembly has two elbows, state the angle between them, measured clockwise.

Common questions

What is an interlock hose fitting?
A fitting that locks the hose’s spiral wire reinforcement directly between its shell and nipple. It may be no-skive or need the hose skived first, depending on the series.
Do spiral hoses need skiving?
Some do. Parker’s No-Skive spiral series crimp over the cover; its ParLock skive series need the cover, and for V4 and V6 the inner tube too, cut back first.
What pressure is R13 and R15 hose rated for?
Parker rates R13 hose at 5,000 psi and R15 at 6,000 psi in every size listed.
Is 4SH a constant-pressure hose?
No. Parker’s 4SH falls from 6,000 psi at -12 to 3,600 psi at -32.
Code 61 or Code 62 flange head?
Code 62 for the highest pressures — Parker rates its Code 62 heads 6,000 psi and Code 61 heads 5,000 psi on spiral hose. Match the head to the port’s code.
Can I crimp skive spiral fittings on any crimper?
Parker says two-piece skive fittings must not be crimped on its Parkrimp crimpers — only on adjustable crimpers of at least 320–340 tons.

What we list

Crimp fittings for spiral hose — including Parker 77 Series and BW series — flange-head hose fittings, split flanges and SAE flanges:

Spiral hose crimp fittings and flanges

IndustryMiningShovels, excavators and haul fleet hydraulics.

Sources

  1. 1.Parker Hannifin. Catalog 4400 — Hose Products (US). ↗
  2. 2.Parker Hannifin. Catalogue 4400/UK — High pressure hose and fittings. ↗
  3. 3.Parker Hannifin. Catalogue 4400/UK — Technical Handbook. ↗
  4. 4.Danfoss (Aeroquip). Rubber Hydraulic Hose & Fitting Catalog. ↗
  5. 5.ISO 12151-3:2021 — Hose fittings with ISO 6162 flange ends (abstract). ↗
MarketSupplying Mali from DubaiFreight, import documents and lead times for mining and processing operations in Mali.MarketSupplying Serbia from DubaiFreight, import documents and lead times for mining and processing operations in Serbia.

What next

  1. 01
  2. 02
  3. 03

    Where the finished assemblies go

    Assemblies are cut to length in Dubai, crimped, tagged, pressure-tested and crated, and that is exactly what makes them practical to send somewhere with no hose shop of its own. A batch built to a measured list travels as one consignment with its test records and arrives ready to fit rather than ready to be made up. The further the site, the larger that difference gets.

    GCC & Middle East

    West & Central Africa

    Everything above ships from the same Dubai warehouse. If your destination is not listed, it is almost certainly still one we quote. See every export destination

Spiral assemblies to build?

Send the hose make and class, the size, both ends and the flange code. We will quote the matching fittings and ferrules, or the finished assembly.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Assembly, crimping & certification

All articles in this topic
A crimping machine crimping a braided hose assembly, finished assemblies on a rack, and a reusable fitting on the bench

Crimped, reusable or ready-made: choosing how to get a hydraulic hose assembly

6 min read

Steel hose fittings: JIC 37° female swivels straight, 45° and 90°, an ORFS female swivel with O-ring, and an NPT male

JIC, ORFS and NPT hose fittings: inch-thread hose ends, drop lengths and how they seal

4 min read

Steel hose fittings with metric and BSP swivels: 24° cone with O-ring, 60° cone, banjo with bolt and washers, JIS flange

BSP, metric, DIN and JIS hose fittings: 60° cones, 24° cones, banjos and Komatsu ends

6 min read

Back to Blog