Skip to content
Assembly, crimping & certification

JIC, ORFS and NPT hose fittings: inch-thread hose ends, drop lengths and how they seal

Most hose assemblies on American and many Asian machines end in one of three inch-thread connections: a JIC 37° swivel, an ORFS swivel with an O-ring in the face, or a pipe thread. Each has its standard (ISO 12151-5, -1 and SAE J516), its seal and its trap — a 45° SAE flare that threads onto a JIC and leaks, an NPSM swivel on a nipple with no 30° seat. The inch hose-end range, including compact and long-drop elbows, and how to order an assembly with two elbows.

Written by
Ayush Bhatia, Director
Published
Updated
Reading
4 min · 2 sections
Share
Steel hose fittings: JIC 37° female swivels straight, 45° and 90°, an ORFS female swivel with O-ring, and an NPT male
Three inch-thread hose ends: a 37° flare, an O-ring face and a tapered pipe thread.

At a glance

Key takeaways

  1. JIC 37° hose ends are ISO 12151-5 / SAE J516 and mate with JIC tube fittings; Parker calls its JIC hose ends fully compatible with its Triple-Lok tube fittings.
  2. ORFS hose ends are ISO 12151-1 and seal on an O-ring in the male face — the choice where vibration or pressure makes a metal seat weep.
  3. NPSM swivel ends seal on the 30° seat of the male NPT, and not every male NPT has one; NPT male hose ends seal on the thread with sealant.
  4. SAE 45° flare and inverted flare hose ends are for low-pressure fuel, refrigerant and brake lines — a 45° flare that threads onto a JIC will leak.
  5. Two elbows on one assembly need the angle between them stated, measured clockwise.

Figures verified · End standards, compatibility, rating and orientation rules from Parker Catalogs 4400 and 4300; flare threads from Parker Catalog 3501E; forms from our listings.

Inch-thread hose ends are the default on North American equipment and common on Asian machines built for export. The family is small — JIC, ORFS, pipe thread and a few SAE flare forms — but each end has variants for clearance and orientation that decide whether an assembly can be fitted at all. This guide covers the range; for the matching adapters see JIC adapters, ORFS and ORB adapters and NPT and NPSM adapters.

/01The end forms.

Inch-thread hose ends
EndStandardSeals onUse
JIC 37° female swivel / maleHighlightedISO 12151-5, SAE J516Metal 37° coneGeneral hydraulics; most common inch hose end
ORFS female swivel / maleISO 12151-1, SAE J516O-ring in the male faceVibration, high pressure, leak-critical lines
NPSM male swivelSAE J51630° seat of the mating fittingPipe-thread ports with a seat
NPT / NPTF maleSAE J516The thread, with sealantPipe-thread ports, lower pressures in large sizes
SAE O-ring male, boss swivelSAE J1926 portO-ring at the portDirect to an ORB port
SAE 45° flare, inverted flareSAE J512 family45° cone; double flare inside the bodyFuel, refrigerant, brake and low-pressure lines

JIC and ORFS nut threads differ for the same dash size — a -8 JIC is 3/4-16, a -8 ORFS 13/16-16 — so the two cannot be mixed up on the machine. The 45° SAE flare is the dangerous one: a ¼" 45° flare nut is 7/16-20, the same as a -4 JIC, and Parker draws the 37° and 45° noses as different profiles. It threads on and does not seal. See 45° flare fittings.

/02Shapes for clearance and orientation.

  • Straight, 45° and 90° female swivels — the basic set.
  • Compact 90° — a tighter bend for crowded valve banks.
  • Long-drop 90° — a longer leg that moves the nut clear of an obstruction or keeps the hose from bending at the ferrule.
  • Double hex — a second hex behind the nut so the fitting can be held while the nut is turned, without twisting the hose.
  • Slip-on nut and thrust-wire nut versions — different ways the swivel nut is retained.

Parker warns against sharp bending at the hose-to-fitting juncture and against installations that twist the hose; an elbow that puts the hose on its natural line is better than a straight end and a forced bend. When an assembly has two elbows, give the displacement angle between them — Parker measures it clockwise.

Common questions

What is a JIC hose fitting?
A hose end with a 37° flare connection (ISO 12151-5, SAE J516) — usually a female swivel that seals on the 37° cone of a male JIC fitting.
JIC or ORFS hose ends?
ORFS where vibration, pressure spikes or leak tolerance matter — it seals on an O-ring. JIC is simpler, metal to metal and remakeable many times.
Why does my NPSM swivel hose leak?
The NPSM swivel seals on a 30° seat in the male fitting; a male NPT without that seat will not seal however tight it is.
What is a long-drop elbow?
A 90° hose end with a longer leg, used to clear an obstruction or avoid bending the hose right at the ferrule.
How do I specify two elbows on a hose assembly?
Give the displacement angle between them, measured clockwise, along with length and both end types.
Can a 45° flare hose end go on a JIC fitting?
No. Some sizes share a thread but the 45° and 37° seats do not seal against each other.

What we list

JIC 37°, ORFS, NPT, NPSM, SAE flare and SAE O-ring hose fittings:

Inch-thread hose fittings

Sources

  1. 1.Parker Hannifin. Catalog 4400 — Hose Products (US). ↗
  2. 2.Parker Hannifin Tube Fittings Division. Catalog 4300 (2017 edition). ↗
MarketSupplying Laos from DubaiFreight, import documents and lead times for mining and processing operations in Laos.MarketSupplying Ethiopia from DubaiFreight, import documents and lead times for construction and plant contractors in Ethiopia.

What next

  1. 01
  2. 02
  3. 03

    Where the finished assemblies go

    Assemblies are cut to length in Dubai, crimped, tagged, pressure-tested and crated, and that is exactly what makes them practical to send somewhere with no hose shop of its own. A batch built to a measured list travels as one consignment with its test records and arrives ready to fit rather than ready to be made up. The further the site, the larger that difference gets.

    Everything above ships from the same Dubai warehouse. If your destination is not listed, it is almost certainly still one we quote. See every export destination

Ordering inch hose ends?

Send the hose, both end types and sizes, any elbow angles and the displacement angle between them. We will quote the ends or the finished assembly.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Assembly, crimping & certification

All articles in this topic
A crimping machine crimping a braided hose assembly, finished assemblies on a rack, and a reusable fitting on the bench

Crimped, reusable or ready-made: choosing how to get a hydraulic hose assembly

6 min read

Stainless braided PTFE hose with stainless hose ends and a cut section of white PTFE tube, beside a textile-covered hose

PTFE (R14) and R5 textile hose ends: two hoses where the dash size is not the bore

5 min read

Twin orange non-conductive thermoplastic hydraulic hoses with crimped fittings along the boom of an aerial work platform

Thermoplastic hose fittings: R7, R8 and R18 hose, non-conductive hose and the 56 Series crimp ends

6 min read

Back to Blog