O-Rings for SAE Hydraulic Flanges

Spare O-rings for SAE J518 four-bolt flange faces, Code 61 and Code 62, 1/2" to 5". The O-ring is the only seal in the joint, so fit a new one whenever the flange is broken. Compound matched to the fluid and temperature you send us.
Key features
- Body Configuration: accessory
- Port A Thread: SAE J518 flange-face O-ring (Code 61 / Code 62 sizes 1/2" to 5")
- Port A Sealing: flange-face
- Nominal Size Range: 1/2" to 5"
- Body Configuration
- accessory
- Port A Thread
- SAE J518 flange-face O-ring (Code 61 / Code 62 sizes 1/2" to 5")
- Port A Sealing
- flange-face
- Nominal Size Range
- 1/2" to 5"
Product description
The O-Rings for SAE Hydraulic Flanges are spare face seals for SAE J518 four-bolt flange connections, Code 61 and Code 62, in sizes 1/2" to 5". The O-ring sits in the groove machined into the flange face and makes the seal on its own: the four bolts only clamp the faces together and hold the ring under compression.
Construction
- Part: spare O-ring for the SAE J518 flange-face groove
- Flange codes: Code 61 (standard pressure) and Code 62 (high pressure)
- Sizes: 1/2" to 5"
- Material: elastomer, with the compound matched to the fluid and temperature
Performance
The O-ring does not set the pressure rating of the joint — that comes from the flange, its code and the bolts that hold it. What the O-ring decides is whether the joint stays dry. A flange that weeps is far more often a flattened, nicked or wrong-compound O-ring, or one pinched out of its groove at assembly, than a fault in the flange itself.
Fitting an O-ring
Fit a new O-ring every time the flange is broken: a used ring has taken a set in its groove and may not seal a second time. Clean the groove and the mating face, check both for scratches across the sealing area, and lightly lubricate the ring with the system fluid so that it stays seated while the halves come together. Draw the bolts up evenly in a cross pattern so the faces close parallel; tightening one side first can squeeze the ring out of its groove.
Choosing the compound
Nitrile suits mineral hydraulic oil at ordinary temperatures. Fluorocarbon (FKM) is the usual step up for higher temperatures and many synthetic fluids. Tell us the fluid, the operating temperature and the pressure, and we will match the compound before quoting.
Applicable Standards
- SAE J518 (matching O-ring spare)
How to order
Specify (a) the flange code (61 or 62) and the nominal size, (b) the fluid and the operating temperature, so the compound can be matched, and (c) the quantity. Indus engineering will confirm the correct part against your equipment.
Companion products
Pair with Indus SAE J518 flanges, split flanges and flange fittings of the same code and size.
Identification
| Parameter | Value |
|---|---|
| Body Configuration | accessory |
Port A
| Parameter | Value |
|---|---|
| Port A Thread | SAE J518 flange-face O-ring (Code 61 / Code 62 sizes 1/2" to 5") |
| Port A Sealing | flange-face |
| Port A Gender | none |
Dimensions
| Parameter | Value |
|---|---|
| Nominal Size Range | 1/2" to 5" |
Construction
| Parameter | Value |
|---|---|
| Material | Elastomer — compound matched to the fluid and temperature |
| Flange Codes | SAE J518 Code 61 and Code 62 |
Compliance
| Parameter | Value |
|---|---|
| Applicable Standards | SAE J518 (matching O-ring spare) |
Shipping & lead time
What are O-rings for SAE hydraulic flanges used for?▾
Which flange sizes do the O-rings for SAE hydraulic flanges fit?▾
How do I choose between Code 61 and Code 62 O-rings?▾
What pressure rating do SAE flange O-rings have?▾
What compound are O-rings for SAE hydraulic flanges made of?▾
Which standard do O-rings for SAE hydraulic flanges follow?▾
What do SAE flange O-rings go with?▾
Can I re-use an SAE flange O-ring, and how do I fit it?▾
Why does an SAE four-bolt flange weep and is it the O-ring?▾
Should I buy flange O-rings separately or a split flange kit?▾
Where do the O-rings for SAE hydraulic flanges come from?▾
Do you stock O-rings for SAE hydraulic flanges in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
The same part, in the designations used across European and Gulf trade catalogues.
- de
- SAE-Flansch SAE
- fr
- bride SAE SAE
- es
- brida SAE SAE
- it
- flangia SAE SAE
From the blog
Written about this range
Specification & standards
SAE J518 Code 61 and Code 62 flanges: telling them apart before you order
Two split-flange halves for the same bore, one rated for far more pressure than the other, and almost nothing on the part to say which is which. The measurement that settles it takes ten seconds.
5 min read
Buying fittings & adapters
SAE flange adapters: Code 61 and Code 62 flange heads, pad adapters and how to choose them
Above 1" and on pump ports, threads give way to four bolts and an O-ring. An SAE flange adapter turns that four-bolt port into a JIC, ORFS, NPTF, ORB or weld connection — in Code 61 to 5,000 psi in small sizes, or Code 62 to 6,000 psi through 2". Flange heads versus flange pad adapters, Code 61 against Code 62, pressure by size, and what an order has to state.
5 min read
Specification & standards
Where JIC is the wrong choice
JIC is the default on most of this continent and it deserves to be. It is also the wrong answer in four specific situations, and every one of them is a situation where people keep specifying it anyway.
4 min read




