Set of Bolts and Spring Washers

Set of Bolts and Spring Washers — Hydraulic SAE Flange family accessory for hydraulic line interconnection. RFQ-only; standard Indus zinc-plated carbon-steel construction.
Key features
- Body Configuration: accessory
- Port A Thread: SAE J429 Grade 5 / Grade 8 bolt set with spring washers, matching SAE J518 4-bolt pattern
- Port A Sealing: none
- Nominal Size Range: 1/2" to 5"
- Body Configuration
- accessory
- Port A Thread
- SAE J429 Grade 5 / Grade 8 bolt set with spring washers, matching SAE J518 4-bolt pattern
- Port A Sealing
- none
- Nominal Size Range
- 1/2" to 5"
Product description
The Set of Bolts and Spring Washers is a Accessory / spare part hydraulic adapter in the Hydraulic SAE Flange family. Set of Bolts and Spring Washers — Hydraulic SAE Flange family accessory for hydraulic line interconnection. RFQ-only; standard Indus zinc-plated carbon-steel construction.
Construction
- Body configuration: Accessory / spare part
- Port A: No port — SAE J429 Grade 5 / Grade 8 bolt set with spring washers, matching SAE J518 4-bolt pattern (No threaded seal)
- Material: Carbon steel (stainless steel available on request)
- Surface treatment: Zinc-plated, Cr3+ passivated, RoHS-compliant
Performance
Working pressure matches the host port grade and the lowest-rated component in the assembly. Operating temperature -40°C to +120°C.. Hydraulic SAE Flange family — SAE J518 4-bolt flanges (Code 61 standard / Code 62 high-pressure) with BSP- or NPT-threaded back, weld-in / weld-on, blind-flange, or accessory variants.
Applicable Standards
- SAE J518
- SAE J429
How to order
Specify (a) the host port size and thread spec on each end, (b) any special seal requirements (bonded seal vs ED seal vs cone seat), and (c) whether you need stainless-steel construction or non-standard surface treatment. Indus engineering will confirm the correct part number against your equipment.
Companion products
Pair with the appropriate Indus tubing or hose ends. For tube assemblies use Indus DIN 2353 cutting rings and end nuts. For hose assemblies pair with Indus crimp ferrules and the matching hose grade.
Identification
| Parameter | Value |
|---|---|
| Body Configuration | accessory |
Port A
| Parameter | Value |
|---|---|
| Port A Thread | SAE J429 Grade 5 / Grade 8 bolt set with spring washers, matching SAE J518 4-bolt pattern |
| Port A Sealing | none |
| Port A Gender | none |
Dimensions
| Parameter | Value |
|---|---|
| Nominal Size Range | 1/2" to 5" |
Construction
| Parameter | Value |
|---|---|
| Material | Carbon steel (stainless on request) |
| Surface Treatment | Zinc-plated, Cr3+ passivated, RoHS-compliant |
Compliance
| Parameter | Value |
|---|---|
| Applicable Standards | SAE J518, SAE J429 |
Shipping & lead time
What is the set of bolts and spring washers for SAE flanges?▾
Which sizes does the SAE flange bolt and spring washer set come in?▾
Why does the bolt set depend on the flange code?▾
What pressure rating does the SAE flange bolt set have?▾
What are the SAE flange bolts made of, and what temperature range do they have?▾
Which standards do the SAE flange bolts and washers follow?▾
What do the SAE flange bolts and spring washers go with?▾
How do I tighten the bolts of an SAE four-bolt flange?▾
When should I replace the bolts on an SAE hydraulic flange?▾
Should I buy a bolt set or a split flange kit?▾
Where does the set of bolts and spring washers come from?▾
Do you stock the set of bolts and spring washers in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog
Written about this range
Specification & standards
SAE J518 Code 61 and Code 62 flanges: telling them apart before you order
Two split-flange halves for the same bore, one rated for far more pressure than the other, and almost nothing on the part to say which is which. The measurement that settles it takes ten seconds.
5 min read
Buying fittings & adapters
SAE flange adapters: Code 61 and Code 62 flange heads, pad adapters and how to choose them
Above 1" and on pump ports, threads give way to four bolts and an O-ring. An SAE flange adapter turns that four-bolt port into a JIC, ORFS, NPTF, ORB or weld connection — in Code 61 to 5,000 psi in small sizes, or Code 62 to 6,000 psi through 2". Flange heads versus flange pad adapters, Code 61 against Code 62, pressure by size, and what an order has to state.
5 min read
Specification & standards
Where JIC is the wrong choice
JIC is the default on most of this continent and it deserves to be. It is also the wrong answer in four specific situations, and every one of them is a situation where people keep specifying it anyway.
4 min read




