Skip to content
Buying fittings & adapters

Metric hydraulic adapters: ISO 6149 and DIN 3852 ports, ED seals, metric cones and Komatsu fittings

An M22×1.5 port can seal on an O-ring in its chamfer (ISO 6149), on a soft seal under the hex (DIN 3852 / ISO 9974 form E) or on a metal edge — and the adapter has to match. Then there are the metric tube ends: 24° cone, 74° cone and the Komatsu 30° flare, whose M33×1.5 thread will not enter an M33×2 port. The steel metric range, the port forms and ratings, and how to order.

Written by
Ayush Bhatia, Director
Published
Reading
7 min · 4 sections
Share
Zinc-plated steel metric adapters in a valve block, one with an O-ring at the port face and others with flat sealing faces
Metric ports seal on an O-ring, a bonded seal or a cutting edge: check which before ordering.

At a glance

Key takeaways

  1. Two metric port families: ISO 6149 (O-ring in the port chamfer, identified by a groove on the stud) and ISO 9974 / DIN 3852 (seal on the port face — an ED soft seal or a metal edge).
  2. ISO says only ISO 6149 ports should be used in new designs; ISO 9974 ports remain everywhere in service.
  3. Ratings depend on series and whether the stud is adjustable: ISO 6149-3 allows 400 bar for fixed and 315 bar for adjustable light-series studs.
  4. Parker’s steel 24° × ISO 6149 connectors run from 500 bar (L) and 800 bar (S) at small sizes down to 250 and 420 bar at large ones.
  5. Komatsu-style 30° flare fittings use metric threads of 1.5 mm pitch throughout — M33×1.5, M42×1.5 — so they do not fit M33×2 or M42×2 ports.

Figures verified · Port forms, sizes, ratings and Komatsu data from Parker Catalog 4300 (2017 edition — check the current edition); ISO 6149-3 limits from the standard’s scope listing.

Metric threads are the default on European machines and common on Asian ones, and the metric part of an adapter drawer is where most mistakes happen — because a metric thread tells you only its diameter and pitch, not how it seals. This guide covers the metric ports, the metric tube ends, the ratings, and the Komatsu fittings that share sizes with neither. For choosing between BSP and metric on a machine, see BSP or metric fittings.

/01The metric port forms.

Metric parallel port forms
FormStandardSeals onIdentify by
O-ring portHighlightedISO 6149-1 (studs ISO 6149-2 / -3)O-ring in the port chamfer under the stud shoulderGroove on the stud hex; optional ridge or "metric" marking on the port
Flat-face port, type EISO 9974-1 / DIN 3852-1ED elastomer seal under the hex on the spot faceFlat spot face, no chamfer O-ring
Flat-face port, O-ring + retaining ringISO 9974-1 / DIN 3852-1O-ring held by a ring on the spot faceWide spot face
Metal edge, form BDIN 3852Machined edge cut into the faceSharp edge on the stud

Parker describes ISO 6149 as a metric parallel thread with a sealing method similar to the SAE straight-thread O-ring port, and lists ISO 6149-1 port sizes from M8×1 to M60×2 (M20×1.5 only for cartridge valve cavities). A port without its identification ridge is meant to be marked "metric" or "ISO 6149-1" on the component. ISO 9974-1 ports seal on the spot face instead; the ED seal sizes follow the thread (M14×1.5 ED14X1.5X, M22×1.5 ED22X1.5X, M27×2 ED26X1.5X, M33×2 ED33X2X).

/02Ratings by size and series.

Parker steel 24° cone × ISO 6149 male connector, bar
L seriesThreadRatingS seriesThreadRating
6LM10×15006SM12×1.5800
10LM14×1.550010SM16×1.5800
12LHighlightedM16×1.540012SM18×1.5630
18LM22×1.540016SM22×1.5630
22LM27×225020SM27×2420
28LM33×225025SM33×2420
42LM48×225038SM48×2420

The standard sets ceilings by stud type: ISO 6149-3 (light series) allows up to 400 bar for non-adjustable stud ends and 315 bar for adjustable ones; the heavy-series ISO 6149-2 is generally given as 630 bar fixed and 400 bar adjustable. So "ISO 6149 = 630 bar" is only true of a fixed heavy-series stud. On the inch side, Parker’s steel 37° JIC × ISO 6149 connectors are rated 7,200 psi at M10, 6,000 psi at M12–M16, 5,000 psi at M18–M27 and 4,000 psi at M33–M42.

The seal form matters too. Parker’s 37° × metric flat-face connectors with an ED seal are rated 5,000 psi at M18–M27, against 3,600 psi at M18–M22 and 3,000 psi at M27 with an O-ring and retaining ring.

/03Metric tube ends: 24°, 74° and 60° cones.

  • 24° cone — the DIN 2353 / ISO 8434-1 cutting-ring connection, in L and S series. Our dedicated range is in DIN 2353 adapters; the metric shelf carries 24° female swivel adapters and dual-purpose studs that fit either a port or a 24° tube nut.
  • Metric 74° cone — a 37° flare form on metric threads, used on some Asian and European machines; our range covers straights, elbows, tees, bulkheads and plugs to BSPT, NPT, ORB and metric studs.
  • JIS metric 60° cone — the Japanese 60° cone on metric threads, with adapters to BSPT, BSP and metric studs.

/04Komatsu-style 30° flare.

Parker describes the Komatsu style as a 30° flare with metric threads, used only as a hose adapter, with a heavy crimp nut for higher assembly torque, generally rated 4,000 psi with full rating in sizes 4 to 16. Every Komatsu thread is 1.5 mm pitch:

Komatsu-style 30° flare sizes (Parker)
Komatsu sizeDash equivalentThread
02-4M14×1.5
03-6M18×1.5
04-8M22×1.5
05-10M24×1.5
06-12M30×1.5
10Highlighted-16M33×1.5
12-20M36×1.5
14-24M42×1.5

Metric ports use M27×2, M33×2 and M42×2 at those sizes, so a Komatsu M33×1.5 nut will not thread onto an M33×2 port — check the pitch with a gauge before you assume. Our range includes Komatsu male connectors to metric, metric flat, NPT and SAE ends.

Common questions

What is an ISO 6149 port?
A metric parallel-thread port that seals on an O-ring in its chamfer, like an SAE ORB port. The stud has an identification groove on its hex, and ISO recommends it for all new designs.
What is the difference between ISO 6149 and DIN 3852?
Where the seal is. ISO 6149 seals on an O-ring in the port chamfer; DIN 3852 / ISO 9974 seals on the flat spot face with an ED soft seal, an O-ring and retaining ring, or a metal edge.
What pressure is an ISO 6149 adapter rated for?
It depends on series, size and whether it is adjustable: ISO 6149-3 allows 400 bar fixed and 315 bar adjustable for light series; Parker’s steel heavy-series connectors reach 800 bar at M12×1.5.
What thread is a Komatsu fitting?
Metric, 1.5 mm pitch at every size (M14×1.5 to M42×1.5), with a 30° flare. It does not fit 2 mm pitch metric ports of the same diameter.
What is a metric 74° cone fitting?
A 37° flare (74° included) connection on metric threads rather than UN/UNF — found on some imported machines.
How do I tell M22×1.5 from M22×2?
With a pitch gauge: 1.5 mm and 2 mm pitch look alike by eye and will not mate.

What we list

Steel metric adapters — ISO 6149 and flat-face studs, metric 74° and JIS 60° cones, 24° swivels and Komatsu fittings:

Metric adapters

IndustryConstructionEuropean and Japanese site machines.

Sources

  1. 1.Parker Hannifin Tube Fittings Division. Catalog 4300 — sections B, E, F, J and T (2017 edition; current edition 9/2023). ↗
  2. 2.EVS-EN ISO 6149-3:2007 — light-duty (L series) stud ends, scope. ↗

What next

  1. 01
  2. 02
  3. 03

    Where these orders go

    Fittings and adapters are the smallest thing we ship and the one that decides whether a machine works, so they travel the way the destination allows: consolidated into a planned consignment where a site is on a long lane, and on their own airway bill when something is standing still. Orders of this kind are quoted from a photograph and a measurement rather than a part number, which is what makes them practical to place from somewhere with no counter nearby.

    Everything above ships from the same Dubai warehouse. If your destination is not listed, it is almost certainly still one we quote. See every export destination

Matching a metric port?

Send the thread with its pitch, how the port seals (O-ring chamfer, flat face, edge) and the other end. We will match the adapter and its seal.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Buying fittings & adapters

All articles in this topic
Plastic push-to-connect pneumatic fittings with blue and black polyurethane air tubes on a machine manifold

Push-to-connect air fittings: how they grip and seal, ratings, tube, and the mistakes that make them leak

4 min read

Brass 45° flare fittings, flared copper tube, compression fittings with sleeves, and an inverted flare union on steel tube

Brass flare and compression fittings: SAE 45° flare, inverted flare and compression — ratings and threads

5 min read

Brass threaded pipe fittings: hex nipple, street elbow, tee, coupling, union, hex bushing, square-head plug and cap

Brass pipe fittings and adapters: NPTF and BSP threads, 1,000 psi ratings, lead-free and DZR brass

5 min read

Back to Blog