BSP is the thread of British, European, Indian, Australian and much Asian equipment, and in the Gulf it is often the first thread a workshop meets. The thread itself is simple — a 55° Whitworth form, parallel or tapered. What makes BSP adapters confusing is that the same G ½ thread can seal four different ways, each with its own rating. For BSPP against BSPT in general see BSPP vs BSPT; this guide is about choosing and ordering the adapters.
/01Threads and sizes.
| Dash | BSPP | TPI | Major diameter |
|---|---|---|---|
| -2 | G 1/8 | 28 | 0.38" (9.73 mm) |
| -4 | G 1/4 | 19 | 0.51" (13.16 mm) |
| -6 | G 3/8 | 19 | 0.65" (16.66 mm) |
| -8Highlighted | G 1/2 | 14 | 0.82" (20.96 mm) |
| -10 | G 5/8 | 14 | 0.90" (22.91 mm) |
| -12 | G 3/4 | 14 | 1.04" (26.44 mm) |
| -16Highlighted | G 1 | 11 | 1.30" (33.25 mm) |
| -20 | G 1-1/4 | 11 | 1.64" (41.91 mm) |
| -24 | G 1-1/2 | 11 | 1.87" (47.80 mm) |
| -32 | G 2 | 11 | 2.34" (59.61 mm) |
BSPT uses the same pitches on a taper. Beware ½" and ¾": NPT and BSP share 14 threads per inch there and nearly the same diameter, so an NPT male will start in a BSP port — and leak, because the 55° and 60° flanks do not match. Parker’s rule is that the tapered families differ in dimensions, pitch and flank angle and do not interchange. A gauge settles it; see measuring a fitting without gauges if you have none.
/02How a BSP end seals.
| Form | Seal | Note |
|---|---|---|
| Type E — "ED" soft sealHighlighted | Elastomer ring held under the hex, on the port face | ISO 1179-2: S series to 630 bar, L series to 250 bar |
| Types G / H — O-ring + retaining ring | O-ring on the stud, held by a ring, on a wide spot face | H is the adjustable version |
| Bonded seal (Dowty) | Steel washer with a bonded rubber lip | Also lets a 60° cone male work as a port stud |
| Type B — metal cutting edge | A machined edge cut into the port face | Metal to metal; rated lowest |
| Tube / series | BSPP | ED seal | Cutting face |
|---|---|---|---|
| 6L, 8LHighlighted | G 1/8, G 1/4 | 500 | 315 |
| 12L | G 3/8 | 420 | 315 |
| 15L | G 1/2 | 400 | 250 |
| 22L–42L | G 3/4–G 1-1/2 | 250 | 160 |
| 6S, 10SHighlighted | G 1/4, G 3/8 | 800 | 400 |
On the inch side, Parker’s steel 37° JIC × BSPP connectors show the same effect: -4 × G 1/8 is 7,200 psi with an ED seal and 5,000 psi with an O-ring and retaining ring; from -16 × G 1 both are 4,000 psi. Its 37° × BSPT male connector is 4,500 psi up to ½" and 2,300 psi from ¾" — the taper caps the adapter. Bonded seals must match the thread size and the spot face; see bonded seal sizing.
/0360° cones and swivels.
The BSP hose and swivel connection is the 60° cone to BS 5200. Parker describes the seal as a single line of contact between the 60° cone seat and the ballnose or cone of the swivel — the BSP equivalent of an NPSM swivel. A male 60° cone can also serve as a port stud in an ISO 1179-1 port if a bonded seal is added, which is why many of our BSP adapters are described as "60° seat or bonded seal". Parker’s steel BSP 60° unions are rated 5,100 psi at ⅛"–¼", 2,900 psi from ⅜" to ¾", 1,700 psi at 1", 1,500 psi at 1¼"–1½" and 1,000 psi at 2" — well below a JIC or ORFS union of the same size.
/04JIS fittings: BSP threads, different seats.
Japanese and Korean machines use JIS fittings, which Parker introduced in the early 1990s for equipment from those countries. They use BSP threads but their own seats: a 30° flare interface and a 60° cone interface, and the JIS B2351 type "O" port with its own O-rings (P8 for 1/8, P11 for ¼, P14 for ⅜, P18 for ½, P24 for ¾, P29 for 1"). Parker stamps its JIS fittings "JIS".
The trap is the 60° cone. Parker states that JIS and BS 5200 60° cones use the same BSPP thread and seat angle, but not all dimensions match — thread length, cone diameter and the BS 5200 bonded-seal locating pilot differ — and that they cannot be interchanged because the differences cause leaks. Parker rates its steel JIS 30° flare adapters at 5,000 psi from ¼" to ½", 4,000 psi at ¾" and 3,000 psi at 1". Our JIS range includes JIS × JIC and JIS × ORFS adapters, JIS × ORB and BSPP elbows, swivel tees and a BSPP-to-JIS 30° converter seat. For the field problem, see the 30° seat problem.
Common questions
- What is the difference between BSPP and BSPT adapters?
- BSPP is parallel and seals on the port face with a soft seal, O-ring, bonded washer or metal edge. BSPT is tapered and seals on the thread with sealant. Both use the 55° Whitworth form.
- What is an ED seal?
- An elastomer seal held in a groove under the hex of a BSPP or metric stud, sealing on the port face (ISO 1179-2 type E). Parker rates ED-sealed studs well above metal-edge studs.
- Can I use a bonded seal instead of an ED seal?
- On a plain BSPP stud with a flat face, yes — size the bonded seal to the thread and the port spot face. An ED stud already carries its own seal.
- Are JIS and BSP fittings interchangeable?
- They share BSP threads, but JIS 30° flare and 60° cone seats are not BS 5200 60° cones. Parker says JIS and BS 5200 60° cone parts cannot be interchanged.
- Why does my NPT fitting fit a BSP port?
- At ½" and ¾" both have 14 TPI and nearly the same diameter, so an NPT male starts in a BSP port. The flank angles differ (60° vs 55°) and it will leak.
- What pressure is a BSP swivel rated for?
- Lower than JIC or ORFS: Parker’s steel BS 5200 60° unions are 5,100 psi at ⅛–¼", 2,900 psi from ⅜–¾" and 1,000 psi at 2".
What we list
Steel BSP adapters, 60° cone and swivel fittings, and JIS 30° adapters:
- Bulkhead Locknut
- Female Thread Cross
- Female Thread Tee
- Swivel Nut Branch Tee (BSP)
- Swivel Nut Run Tee (BSP)
- Union Tee BSPT
- Male Stud Branch Tee
- Union Tee (BSP)
- Male Stud Run Tee
- Female Swivel Cap
- Hexagon Socket Plug
- Blanking Plug for Ports with ED Seal
- Hex Head Plug
- Female Thread Elbow
- BSP Plug
- BSP Female Connector
- Male Female Thread Adaptor BSPT
- Thread Reducer
- Thread Adaptor BSP ED Seal
- Male Female Thread Elbow
- Swivel Nut Union
- Swivel Male Stud BSPT
- Swivel Male Elbow NPT
- Swivel Male Stud NPT
- Swivel Male 45° Elbow
- Bulkhead Union
- Union Elbow BSPT
- Union BSPT
- Male Stud 45° Elbow BSPT
- Male Stud Elbow BSPT (BSP)
- Male Stud Elbow UNF O-Ring
- Male Stud Connector BSPT (BSP)
- Male Stud 45° Elbow UNF O-Ring
- Male Stud Connector UNF O-Ring
- Male Stud 45° Elbow NPT
- Male Stud Elbow NPT (BSP)
- Male Stud Elbow JIC
- Male Stud Connector NPT (BSP)
- Male Stud Connector JIC
- Male Stud Connector Metric O-Ring
- Male Stud 45° Elbow BSPP O-Ring
- Male Stud Connector BSP O-Ring
- Union 45° Elbow
- Union Elbow
- Union
- BSP Female 60° Cone
- 90° Elbow BSP Male 60° Seat × BSP Male O-Ring Adjustable Stud End
- BSP Male 60° Seat or Bonded Seal × NPT Female
- BSP Male 60° Seat or Bonded Seal × BSPT Female
- BSP Male O-Ring × BSP Female
- 90° Elbow BSP Male 60° Seat Bulkhead
- BSP Male 60° Seat or Bonded Seal × Butt-Weld Tube
- Butt-Weld Tube × BSP Female 60° Cone
- 45° Elbow BSP Male 60° Seat × Metric Male
- 90° Elbow BSP Male 60° Seat × Metric Male
- BSP Male 60° Seat or Bonded Seal × Metric Male 60° Seat or Bonded Seal
- BSP Male 60° Seat or Bonded Seal × JIC Female 74° Seat
- 90° Elbow BSPT Male × BSP Female 60° Cone
- BSPT Female
- 90° Elbow BSPT Female
- 90° Elbow BSPT Male 60° Seat × BSPT Female
- BSP Male O-Ring × BSPT Female
- BSPT Male 60° Seat Plug
- JIS Gas Male 60° Cone × JIS Gas Male 60° Cone
- JIS Gas Male 60° Cone × BSPT Male 60° Seat
- 45° Elbow JIS Gas Male 60° Cone × BSPT Male 60° Seat
- 90° Elbow JIS Gas Male 60° Cone × BSPT Male 60° Seat
- Steel BSPT Male × NPTF Male Adapter
- Steel JIC 37° Male × BSP Female Adapter
- Steel BSPP Test Port Tee, Male × Female Swivel × 1/8" BSP Port
- Steel BSPP Female Swivel × JIC 37° Female Swivel Adapter
- Steel BSPT Male × BSP Female Adapter
- Steel BSPP Male × ORB Female Adapter
- Steel BSPT Male × NPTF Female Adapter
- Steel BSPP Female × NPTF Female Adapter
- Steel BSPP Female Swivel 45° Elbow
- Steel JIC 37° Male × BSPP Female Swivel 90° Elbow
- Steel BSPP Male × JIC 37° Female Swivel 90° Elbow
- Steel BSPP Male × ORB Adjustable Run Tee
- Steel BSPP Male × ORB Adjustable Branch Tee
- Steel BSPP Female Swivel Tee
- Steel BSPP Male × BSPP Female Swivel Branch Tee
- Steel BSPP Male × BSPP Female Swivel Adapter Tee
- Steel BSPP Male Cross
- Steel JIC 37° Male × BSPP Adjustable Branch Tee
- Steel JIC 37° Male × BSPT Male Run Tee
- Steel JIC 37° Male × BSPT Male Branch Tee
- Steel JIC 37° Male × BSPP Female Flat-Face Swivel Adapter
- Steel Komatsu M16 Male × BSPT Male Adapter
- Steel JIC 37° Male × BSPP Female Swivel Adapter
- Steel ORFS Male × JIS 30° Female Adapter
- Steel ORFS Male × JIS 30° Male Adapter
- Steel JIC 37° Male × JIS 30° Female Adapter
- Steel JIS 30° Hex Head Plug
- Steel JIS 30° Female Cap
- Steel JIC 37° Female × JIS 30° Female Adapter
- Steel JIS 30° Male × BSPP Adjustable 90° Elbow
- Steel JIS 30° Male × ORB Male Adapter
- Steel JIS 30° Male × ORB Adjustable 90° Elbow
- Steel JIS 30° Male × JIS 30° Female Swivel Run Tee
- Steel JIS 30° Male × JIS 30° Female Swivel 90° Elbow
- Steel JIC 37° Male × JIS 30° Male Adapter
- Steel 30° Sealing Seat, BSPP Male to JIS 30° Converter
BSP and JIS adapters
IH-AD-BSP-040Male Stud Connector UNF O-RingIndus Hydraulics
IH-AD-BSP-020Thread Adaptor BSP ED SealIndus Hydraulics
IH-AD-BSP-054BSP Female 60° ConeIndus Hydraulics
IH-AD-BSP-025Swivel Nut UnionIndus Hydraulics
IH-ST-9240Steel JIC 37° Male × BSPP Female Swivel AdapterIndus Hydraulics
IH-ST-9061Steel BSPP Male × JIC 37° Female Swivel 90° ElbowIndus Hydraulics
IH-ST-9220Steel JIC 37° Male × JIS 30° Female AdapterIndus Hydraulics
IH-ST-9999Steel 30° Sealing Seat, BSPP Male to JIS 30° ConverterIndus Hydraulics




