Skip to content
Cylinders, pumps & motors

Hydraulic control valves: directional, relief, flow control and flow dividers explained

A hydraulic circuit is steered by a handful of valve types: a directional valve that sends oil to one side of a cylinder or the other, a relief valve that caps the pressure, flow controls and dividers that set speed, and check and selector valves that hold or route the flow. How monoblock spool valves, CETOP 3 solenoid valves and modular stacks work, what open and closed centre mean, and what to send to get the right replacement.

Written by
Ayush Bhatia, Director
Published
Updated
Reading
5 min · 3 sections
Share
Two-spool monoblock directional valve with lever handles, a cartridge flow control, in-line check and gear flow divider
Direction, pressure, speed and split: four valve jobs in one circuit.

At a glance

Key takeaways

  1. Directional valves choose where oil goes; relief valves cap pressure; flow controls and dividers set speed; check and selector valves hold and route flow.
  2. Match the centre type to the pump: open-centre valves suit fixed-displacement gear pumps, closed-centre valves suit pressure-compensated pumps.
  3. Monoblock valves carry a built-in relief — Cross ships its Model BA set at 2,000 psi — which must be set for the circuit, not left as found.
  4. CETOP 3 (ISO 4401-03) solenoid valves such as Yuken’s DSG-01 are rated 63 L/min and 315 kgf/cm².
  5. A pressure-compensated flow control holds speed as load changes; a plain needle valve does not.

Figures verified · Valve functions and ratings from Cross, Prince and Yuken maker documents.

On a tractor, log splitter, loader or press, the pump makes flow and the valves decide what it does. Replacing a valve is mostly a matching exercise — spool count and type, centre, ports, relief setting and flow — and most failures to work after a swap come from one of those being different, not from a faulty valve. This guide sits alongside the pump and cylinder guides in this section: see hydraulic pump types and hydraulic cylinders.

/01Directional control valves.

A spool valve slides a spool in a bore to connect the pump and tank to the work ports. A monoblock valve has one to three spools in one casting; a sectional valve bolts sections together. Typical mobile monoblocks are 3-position, 4-way and spring-centred: Cross’s Model BA runs 2,500–3,000 psi at 30 GPM with one to three spools; Prince’s RD2500 is rated 3,000 psi with a 150 psi tank-port limit.

  • Open centre — in neutral the pump flow returns to tank. The normal choice with a fixed-displacement gear pump.
  • Closed centre — in neutral the pump port is blocked. Used with pressure-compensated or load-sensing pumps; Cross sells a conversion kit for its BA valve.
  • Power beyond — the neutral flow is carried on, under pressure, to a second valve downstream instead of to tank.
  • Float — a fourth spool position that connects both work ports to tank, so a loader bucket or blade can follow the ground.
  • Detents hold the spool in position; log-splitter valves use an auto-return detent that kicks the spool back to neutral at the end of the stroke.

Industrial circuits use solenoid valves on a standard mounting face. Yuken’s DSG-01 sits on the ISO 4401-03 (CETOP 3, NG6) pattern and is rated 63 L/min at 315 kgf/cm²; its model code gives positions and spring arrangement — 3C is three-position spring-centred, 2B two-position spring-offset — and the coil voltage.

/02Relief, check and selector valves.

  • Relief valves open to tank when pressure reaches the setting, protecting the pump, hoses and cylinder. Pilot-operated reliefs such as Cross’s Model RV (400–3,000 psi, 40 GPM) or Yuken’s BG-03 (up to 250 kgf/cm², 100 L/min) hold the setting more closely over a range of flow. Yuken’s instruction for the BG-03: pipe its tank line straight to the reservoir, not into another valve’s tank line.
  • Check valves let oil through one way only — to hold a load, isolate a pump or bypass a filter.
  • Selector valves send one supply to one of two circuits: Cross’s SD4 is a manual 6-way, 2-position valve. Not every “sequence” valve sequences by pressure — Cross’s SQV is an alternating valve for row-marker cylinders on planters.
  • Modular valves stack under a solenoid valve on the same face — Yuken’s 01 series stacks one to five valves at 250 kgf/cm² and 35 L/min, including a brake valve (MBR-01) that controls a running-away load.

/03Flow control and flow dividers.

A needle valve is a variable orifice: flow through it changes when the load pressure changes. A pressure-compensated flow control holds flow nearly constant as pressure varies — Prince’s RD100 does this at up to 3,000 psi and 30 GPM, sending excess flow to a second port that can feed another circuit or return to tank. Priority dividers feed one circuit first (steering, typically) and pass the rest on; proportional dividers split flow between two circuits, by spool or by a set of rotary gears turning together. Cross’s FD is a proportional divider used to stop one wheel spinning out on a hydrostatic drive.

Common questions

Open centre or closed centre valve?
Open centre for a fixed-displacement (gear) pump, so flow returns to tank in neutral; closed centre for a pressure-compensated or load-sensing pump.
What is power beyond?
A port or sleeve that carries the valve’s neutral flow on to a second valve under pressure, instead of returning it to tank.
What is a CETOP 3 valve?
A valve on the ISO 4401-03 (NG6) mounting face — the common small industrial pattern, used by valves such as Yuken’s DSG-01.
Why does my cylinder speed change with load?
A plain needle valve is not pressure-compensated; use a pressure-compensated flow control to hold speed as load varies.
What should I send to replace a monoblock valve?
The number of spools, spool type and detents, open or closed centre, port threads, flow, relief setting and any power-beyond or float function — or a photo of the nameplate.

What we list

Directional, solenoid, relief, check, selector and flow-control valves and flow dividers:

Hydraulic control valves

Sources

  1. 1.Cross Manufacturing. Hydraulic valve product pages (Model BA, SD4, RV, SQV, FD). ↗
  2. 2.Prince Manufacturing. Hydraulic valve product pages (RD2500, RD100). ↗
  3. 3.Yuken India. DSG-01 Series Solenoid Operated Directional Valves. ↗
  4. 4.Yuken India. Pilot Operated Relief Valves. ↗
MarketSupplying Switzerland from DubaiFreight, import documents and lead times for steel and metals plants in Switzerland.

What next

  1. 01
  2. 02
  3. 03

    Where cylinders, pumps and motors like these go

    A cylinder, pump or motor is rarely bought on its own: it arrives with the hoses, fittings, seals and valves that connect it, and it has to match a mount, a shaft and a port that are already on the machine. We work from the bore, rod, stroke and mount of the cylinder you are replacing, or the displacement, shaft and flange of the pump or motor, quote the component and its connections as one consignment, and ship it from Dubai with the documents the destination asks for.

    Everything above ships from the same Dubai warehouse. If your destination is not listed, it is almost certainly still one we quote. See every export destination

Replacing a hydraulic valve?

Send a photo of the nameplate, or the spool count, centre type, port threads, flow and relief setting. We will match the valve and any detent kits, handles or cables it needs.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Cylinders, pumps & motors

All articles in this topic
Hydraulic reservoir with breather and sight glass, bell housing, jaw coupling hubs and spider, filter and accumulator

Hydraulic power unit components: reservoirs, filters, bell housings, couplings and accumulators

4 min read

Back to Blog