Skip to content
Industrial hose

Cryogenic, chlorine, steam-jacketed and heated metal hose: specialty assemblies explained

Some liquids cannot go through an ordinary hose: liquid nitrogen and oxygen at −196 and −183 °C, chlorine that attacks most metals, asphalt and sulphur that set solid if they cool. Specialty corrugated metal hose handles each — with CGA V-6 cryogenic ends and foam or vacuum insulation, all-Monel or Hastelloy construction to Chlorine Institute rules, a steam jacket or an electric heating cable. What each type is, the ratings makers publish, and what “CGA96” on a hose does and does not mean.

Written by
Ayush Bhatia, Director
Published
Updated
Reading
4 min · 4 sections
Share
Insulated braided stainless cryogenic hose from a tanker to a plant fill point, with a metal pipe loop behind
Cryogenic hose loses far less product per fill with its insulation cover on.

At a glance

Key takeaways

  1. Thorburn’s cryogenic unloading hose is braided corrugated stainless rated 400 psi (27.6 bar), −269 to 538 °C, with CGA V-6 connections; vacuum-jacketed hose is a separate design.
  2. CO₂ hose is lined (helical or PTFE) to reduce snowballing; oxygen hose is cleaned and capped for oxygen service.
  3. Chlorine hose is all-Monel (Thorburn M96ZC, tested at 750 psi) or C276 (Hose Master ChlorSafe), built to Chlorine Institute Pamphlet 6 Appendix A.
  4. “CGA96” in Thorburn’s catalogue is a Canadian Gas Association fuel-gas certification — not an oxygen or argon standard.
  5. Steam-jacketed hose is a hose within a hose; electrically heated hose holds a set temperature with an MI cable and RTD.

Figures verified · Ratings and constructions from the Thorburn catalogue and ThermaCover brochure, and Hose Master product pages.

Corrugated stainless hose is the default answer whenever rubber cannot take the temperature or the chemistry. The specialty assemblies build on it: insulation for cryogens, exotic alloys for chlorine, jackets and heating cables for products that must stay hot. For the basics of corrugated metal hose — braid, pressure and bend radius — see the metal hose guide; for nickel alloys, exotic alloy metal hose.

/01Cryogenic transfer hose.

Common cryogens (Thorburn catalogue boiling points)
LiquidNormal boiling pointHose notes
Liquid oxygen (LOX)Highlighted−183.0 °CCleaned for oxygen service; CGA V-6 OX connections
Liquid nitrogen (LIN)−195.8 °CCGA V-6 NI connections
Liquid argon (LAR)—CGA V-6 AR connections
Liquid CO₂—Helical or PTFE liner against snowballing; brass ACME ends
LNG≈ −160 °CUnloading hose, or vacuum-jacketed hose for ship-to-shore

Thorburn’s cryogenic unloading hose is a braided corrugated stainless hose, with optional armour, rated to 400 psi (27.6 bar) and −269 to 538 °C; high-pressure versions go to 3,500 psi. End connections for LIN, LOX and LAR comply with CGA V-6, using NI, OX and AR ACME fittings so a nitrogen hose cannot be connected to an oxygen system. Insulation is either a Cryo-Therm foam cover (−196 to 302 °C) — Thorburn’s example is 25 L of LN2 lost per fill on a bare hose against 2.5 L with the cover — or a vacuum jacket on its TJHC hose. Hose Master builds corrugated hose for temperatures as low as −325 °F and LNG hose with ABS type approval.

/02Chlorine hose.

Chlorine transfer hose is built to the Chlorine Institute’s Pamphlet 6, Appendix A. Thorburn’s M96ZC is all Monel 400 — core, braid and filler — with an Armor-Flex guard; every assembly is tested at 750 psi, then tagged, cleaned and capped. Hose Master’s ChlorSafe uses C276 alloy for every wetted part and the braid, rated 375 psi in ¾–2 in with a 5:1 safety factor and helium leak-tested. Use only the alloy and construction the pamphlet allows, and replace on the operator’s schedule.

/03Jacketed and heated hose.

  • Steam-jacketed hose (Thorburn TJH) is a hose within a hose: product inside, steam in the jacket, each a separate pressure carrier, joined by port couplings. Used for asphalt, pitch, sulphur, slurry and viscous chemicals. A double-containment version adds a breach warning.
  • Electrically heated hose (Thorburn Sure-Temp) wraps the hose in a spiral MI heating cable with a Pt100 RTD and controller: 5–250 °C for liquids, 5–450 °C for gas sampling, typically to 300 psi (20 bar), with an FM Class I Div 2 Group D option.
  • Removable insulation covers (ThermaCover) keep heat in and protect people: fibreglass jackets rated to 260 °C over aerogel or mineral-wool cores.

/04Pipe loops.

A Thor-Loop is two metal hoses and a 180° return set into a pipe run, in a U or V shape, absorbing up to 500 mm (20 in) of thermal and seismic movement in every direction. Thorburn lists them as UL-listed and CGA-certified for sprinkler and gas systems; support the return in any orientation other than hanging down.

Common questions

What pressure is a cryogenic transfer hose rated for?
Thorburn’s cryogenic unloading hose is rated 400 psi (27.6 bar); high-pressure versions are available to 3,500 psi.
What is CGA V-6?
The Compressed Gas Association standard for cryogenic liquid transfer connections, with different fittings for nitrogen, oxygen and argon so they cannot be cross-connected.
Why do CO₂ hoses snowball?
Liquid CO₂ flashes to dry ice as pressure drops; lined hoses (helical or PTFE) are designed to reduce the build-up.
What hose is used for chlorine?
All-Monel or C276 corrugated hose built to Chlorine Institute Pamphlet 6, Appendix A.
Steam-jacketed or electrically heated hose?
Steam where plant steam is available and the product needs a lot of heat; electric where there is no steam or the temperature must be held precisely.

What we list

Cryogenic, chlorine, steam-jacketed and heated hose, pipe loops and insulation covers:

Specialty metal hose

IndustryLNG & future fuelsCryogenic transfer and bunkering.

Sources

  1. 1.Thorburn Flex. Metallic Hose Assemblies catalogue. ↗
  2. 2.Thorburn Flex. ThermaCover brochure. ↗
  3. 3.Hose Master. ChlorSafe corrugated metal hose. ↗
  4. 4.Hose Master. Cryogenics. ↗

What next

  1. 01
  2. 02
  3. 03

    Where we supply this hose

    For chemical, food-grade, steam and water hose the certificate is most of what the buyer is actually purchasing, so it is prepared before dispatch rather than chased afterwards. We ship this class of hose from Dubai into plants audited against the same standards we quote to, with the documentation attached to the consignment and referenced on the invoice.

    Everything above ships from the same Dubai warehouse. If your destination is not listed, it is almost certainly still one we quote. See every export destination

Need a specialty metal hose?

Send the fluid, its temperature and pressure, the bore and length, both end connections and any standard the plant works to. We will confirm the build with the maker.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Industrial hose

All articles in this topic
Boat engine room with double-clamped black and blue wet exhaust hose and clear helix bilge hose to a bilge pump

Marine hose: fuel hose types A1 and A2, wet exhaust hose, bilge and water hose

5 min read

Back to Blog