Skip to content
Industrial hose

Fire sleeves and metal hose guards: what “fire-safe” means, and how interlocked hose differs

A silicone-coated fire sleeve buys a hydraulic hose a few minutes near a furnace; an interlocked metal hose carries dust, exhaust or grain but is not leak-tight; a ball-joint guard protects a hose from impact and molten splash. What the maker’s fire ratings actually say — continuous versus 15-minute versus 30-second — why “fire-safe” on a hose usually borrows a valve standard, and how to choose between lock-section, Smooth-Flex and Armor-Flex.

Written by
Ayush Bhatia, Director
Published
Reading
3 min · 2 sections
Share
Braided metal hose in a red silicone fire sleeve, interlocked lock-section hose, ball-joint armour guard and fire tape
Sleeve, interlock or armour: each protects a hose from something different.

At a glance

Key takeaways

  1. Read fire-sleeve ratings by duration: Thorburn’s Fry-Sil jacket is 260 °C continuous, 1090 °C for 15–20 minutes, 1650 °C for 15–30 seconds.
  2. API 6FA, API 607 and ISO 10497 are fire tests for valves; ISO 15540/15541 cover non-metallic hose on ships — check what a “fire-safe” hose claim actually cites.
  3. Interlocked (stripwound) hose is not leak-tight unless packed; it carries air, exhaust and dry bulk, or protects other hoses.
  4. Smooth-Flex is interlocked hose with a smooth liner for bulk conveying, rated only to about 15–20 psi.
  5. Ball-joint Armor-Flex guards have no interlocking parts to limit bending; with insulation Thorburn rates them to 1100 °C.

Figures verified · Ratings and constructions from the Thorburn metallic hose catalogue and Witzenmann; standard scopes from ISO and FM Approvals.

Hoses near furnaces, ladles, welding bays and hot exhausts fail from the outside in. The usual fixes are a fire sleeve over the hose, a metal guard around it, or an all-metal hose in place of it. Each protects against something different, and the ratings that sell them are easy to misread. For corrugated pressure-tight metal hose itself, see corrugated stainless steel hose and the metal hose guide.

/01Fire sleeves and fire tape.

Thorburn FJ72 Fry-Sil fire jacket ratings
ExposureRating
ContinuousHighlighted260 °C (500 °F)
15–20 minutesUp to 1090 °C (2000 °F)
15–30 secondsUp to 1650 °C (3000 °F)

The jacket is woven fibreglass coated in iron-oxide silicone rubber: it protects against molten spatter and short flame exposure, and is oil- and water-resistant. It does not make a hose rated for 1000 °C service — the continuous figure is the one to design to. Where a sleeve cannot be slid on because the hose or cable cannot be disconnected, the same material comes as fire tape (FJ73) in 1, 2 and 3 in widths.

/02Interlocked hose and guards.

Thorburn metal hose guards and interlocked hose
ProductConstructionPressureUse
LS lock sectionHighlightedSingle strip, S-profile interlockNot leak-tight unless packedAir, exhaust, dry bulk, protective casing
SFM Smooth-FlexInterlock with smooth inner linerAbout 15–20 psi with packingPneumatic and gravity bulk conveying
AF Armor-FlexConcave and convex ball-joint sectionsNone — a guardImpact, abrasion and molten splash protection

Interlocked hose’s temperature limit is set by its packing, not just its metal: Thorburn gives cotton and elastomer packing to 180 °F, Pyro-Pak to 1000 °F, and hard copper or stainless wire to 1200 °F. Witzenmann gives material limits of 400 °C for hot-dip galvanised steel and 600 °C for 1.4301 stainless. Galvanised steel belongs in guards and interlocked hose, never in a pressure-tight corrugated core.

Armor-Flex is different in kind: an articulated shield of rolling sections with nothing to restrict bending, fitted over a metal or rubber hose. Thorburn makes it in carbon steel, 304 and 316 stainless.

Common questions

How hot can a hose fire sleeve go?
Thorburn’s Fry-Sil jacket is rated 260 °C continuous, 1090 °C for 15–20 minutes and 1650 °C for 15–30 seconds. Design to the continuous figure.
Is interlocked metal hose leak-tight?
No, not on its own — it can be supplied packed for better sealing. It suits air, exhaust and dry bulk, not pressurised liquids.
What is a fire-safe hose?
There is no single standard. All-metal hose is fire-resistant by construction; check whether a claim cites a hose test or a valve test such as API 6FA.
What is Smooth-Flex hose for?
Pneumatic and gravity conveying of dry bulk such as grain, pellets and powders — interlocked hose with a smooth liner, at low pressure.

What we list

Fire jackets, fire tape, interlocked hose and hose guards:

Fire sleeves and hose guards

IndustrySteelHoses near furnaces, ladles and casters.

Sources

  1. 1.Thorburn Flex. Metallic Hose Assemblies catalogue. ↗
  2. 2.Witzenmann. Stripwound hoses. ↗
  3. 3.ISO 15541:2016 — Fire resistance of non-metallic hose assemblies and compensators — test bench. ↗
  4. 4.FM Approvals. Standard 1637 — Flexible Sprinkler Hose with Threaded End Fittings. ↗

What next

  1. 01
  2. 02
  3. 03

    Where we supply this hose

    For chemical, food-grade, steam and water hose the certificate is most of what the buyer is actually purchasing, so it is prepared before dispatch rather than chased afterwards. We ship this class of hose from Dubai into plants audited against the same standards we quote to, with the documentation attached to the consignment and referenced on the invoice.

    GCC & Middle East

    Western & Northern Europe

    Everything above ships from the same Dubai warehouse. If your destination is not listed, it is almost certainly still one we quote. See every export destination

Protecting hoses from heat?

Send the hose OD, the length to cover, the heat source and how long the exposure lasts. We will quote a sleeve, tape, guard or all-metal hose.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Industrial hose

All articles in this topic
Boat engine room with double-clamped black and blue wet exhaust hose and clear helix bilge hose to a bilge pump

Marine hose: fuel hose types A1 and A2, wet exhaust hose, bilge and water hose

5 min read

Back to Blog