Skip to content

JIC Adapters

137 SKUs7 brands

Showing 97–137 of 137 SKUs

Category image · Hoses & Fittings
Category image · Hoses & Fittings
Branch tee swivel connector, JIC 37° male run with female swivel branch

Branch Tee Swivel Connector JIC

Indus Hydraulics37-coneup to 350 bar (5000 psi)
Inquire
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
90° JIC 37° male bulkhead elbow, long threaded leg with locknut

90° Elbow JIC Male 74° Cone Bulkhead

Indus Hydraulics90 elbow bulkhead-04 to -20
Inquire
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
Category image · Hoses & Fittings
45° elbow adapter, JIC 37° male flare × BSP O-ring adjustable stud end

45° JIC Male 74° Cone × BSP Male O-Ring Adjustable Stud End

Indus Hydraulicsup to 315 bar (4,569 psi), manufacturer stated-04 to -24
Inquire
45° elbow adapter, JIC 37° male flare, forged zinc-plated steel

45° JIC Male 74° Cone

Indus Hydraulicsup to 345 bar (5,004 psi), manufacturer stated45 elbow
Inquire
45° female swivel connector, JIC 37° female swivel both ends, zinc-plated steel

45° Female Swivel Connector JIC

Indus HydraulicsJIC 37° UN/UNF (7/16-20 to 1-7/8-12)up to 350 bar (5000 psi)
Inquire
45° elbow adapter, JIC 37° male flare × NPT male, forged zinc-plated steel

45° Elbow JIC Male 74° Cone × NPT Male

Indus Hydraulics45 elbowJIC 37° cone (74° included)
Inquire
45° JIC 37° male bulkhead elbow, long threaded leg with locknut, flare both ends

45° Elbow JIC Male 74° Cone Bulkhead

Indus Hydraulicsbulkheadup to 345 bar (5,004 psi), manufacturer stated
Inquire

Questions we get asked

About this range

01What does the dash size mean?
The nominal size in sixteenths of an inch: a -08 is 8/16, or 1/2 inch nominal. On a JIC end it identifies the thread — a -08 is 3/4-16 UNF — rather than the bore exactly.
02Can I tighten a JIC joint harder to stop a leak?
No. The seal is the flare, and over-tightening damages it. Make the joint up by flats from finger tight, and if a correctly made joint still weeps, inspect the flare for scratches or distortion.
03Is JIC the same as SAE 45° flare?
No. They share threads on several sizes, but JIC seals on a 37° flare and SAE 45° on a 45° flare. A joint mixing the two may hold briefly, then leak.
04Why choose a JIC × SAE O-ring boss adapter rather than JIC × NPT for a port?
Because an O-ring boss seals on an elastomer O-ring, not on the thread, so it can be remade without losing engagement and, in adjustable form, aimed in any direction. An NPT end seals by thread interference, is rated lower than the O-ring boss in larger sizes, and goes deeper every time it is remade. Note that an O-ring boss end uses the same UN thread as the JIC end of the same dash size: tell them apart by the O-ring at the shoulder.
05How is a JIC bulkhead adapter fitted through a panel?
The long threaded body passes through a hole in the panel and is clamped by the bulkhead locknut, which tightens against the panel rather than sealing anything. Size the hole for the thread with a small clearance and keep the panel within the thickness the body can take. Hold the body while tightening the locknut, then make up the lines on each side by flats as for any JIC joint.
06How do I blank off a JIC line or port?
Use a JIC plug in a female swivel nut and a JIC swivel cap on a male end; both seal on the 37° flare in the same way as a working joint. Make them up by flats from finger tight like any JIC connection, not harder. For a port rather than a hose or tube end, blank it with a plug for that port type, such as an O-ring boss or BSP plug.
07What types of JIC adapter are there?
JIC adapters are 37° flare fittings with UN/UNF threads. The range covers JIC to JIC, NPT, BSP, BSPT, metric and SAE O-ring boss, as straight connectors, swivels, 45° and 90° elbows, tees, crosses, bulkheads, plugs and caps.
08What sizes do JIC adapters come in?
Threads start at 7/16-20, with dash sizes -04 to -24 on the 45° elbows and -04 to -20 on the bulkheads. Some are manufacturer-stated up to 345 bar (5,004 psi). The size table on this page lists each adapter.