Skip to content

JIC Adapters

137 SKUs7 brands

Showing 49–96 of 137 SKUs

Steel JIC 37° long flare nut, angled view

Steel JIC 37° Long Flare Nut

Indus Hydraulicsnut or sleeve for a 37° flared tube endJIC tube end, 3/16" to 2" tube O.D.
Inquire
Steel Convert-A-Flare tube sleeve, JIC 37° to flareless, angled view

Steel Convert-A-Flare Tube Sleeve, JIC 37° to Flareless

Indus Hydraulicsnut or sleeve for a 37° flared tube endconvert-a-flare sleeve
Inquire
Steel Convert-A-Flare tube nut, JIC 37° to flareless, angled view

Steel Convert-A-Flare Tube Nut, JIC 37° to Flareless

Indus Hydraulicsnut or sleeve for a 37° flared tube endJIC tube end, 1/4" to 1-1/4" tube O.D.
Inquire
Straight adapter, SAE O-ring boss male × JIC 37° female swivel nut

SAE O-Ring Boss × JIC Female 74° Seat

Indus Hydraulicsup to 315 bar (4,569 psi), manufacturer statedstraight
Inquire
Run tee swivel connector, JIC 37° male run with female swivel end

Run Tee Swivel JIC

Indus Hydraulics-04 to -32 (1/4" to 2")run-tee
Inquire
JIC 37° male plugs, zinc-plated steel hex, two shown

Plug JIC

Indus Hydraulicsup to 350 bar (5000 psi)-04 to -32 (1/4" to 2")
Inquire
Straight adapter, metric male captive seal × JIC 37° female, hex body

Metric Thread Male Captive Seal × JIC Female 74° Seat

Indus Hydraulics-10 to -33Metric M10×1 to M33×1.5
Inquire
Straight adapter, metric male × JIC 37° female swivel nut, zinc-plated steel

Metric Male × JIC Female 74° Seat

Indus Hydraulicsup to 345 bar (5,004 psi), manufacturer statedMetric M10×1 to M33×1.5
Inquire
JIC male tee, 37° flare on three ends, forged zinc-plated steel

Male Tee JIC

Indus HydraulicsJIC 37° UN/UNF (7/16-20 to 1-7/8-12)37-cone
Inquire
JIC male cross, four 37° flare ends, forged zinc-plated steel

Male Cross JIC

Indus Hydraulics-04 to -32 (1/4" to 2")up to 350 bar (5000 psi)
Inquire
Straight male connector, JIC 37° male flare both ends, zinc-plated steel

Male Connector JIC

Indus Hydraulics37-conestraight
Inquire
Straight adapter, BSPT male × JIC 37° female swivel nut, zinc-plated steel

BSPT Male × JIC Female 74° Seat

Indus HydraulicsstraightBSPT taper thread
Inquire
JIC bulkhead locknut, thin zinc-plated steel hex

Lock Nut JIC

Indus Hydraulicsnonelock-nut
Inquire
Run tee, JIC 37° male flare × SAE O-ring boss adjustable stud with locknut

JIC Male 74° Cone × SAE O-Ring Boss Run Tee

Indus Hydraulics-04 to -24UN/UNF 7/16-20 to 1.7/8-12
Inquire
Straight adapter, JIC 37° male flare × BSP male O-ring, zinc-plated steel

JIC Male 74° Cone × BSP Male O-Ring

Indus Hydraulics-04 to -24JIC 37° cone (74° included)
Inquire
Straight adapter, JIC 37° male flare × BSP male captive seal, zinc-plated steel

JIC Male 74° Cone × BSP Male Captive Seal

Indus HydraulicsUN/UNF 7/16-20 to 1.7/8-12-04 to -24
Inquire
JIC 37° male bulkhead branch tee (AJJ6J), long threaded branch with locknut

JIC Male 74° Cone Bulkhead Branch Tee (AJJ6J)

Indus Hydraulics-04 to -24JIC 37° cone (74° included)
Inquire
JIC 37° male bulkhead branch tee, long threaded branch with locknut

JIC Male 74° Cone Bulkhead Branch Tee

Indus Hydraulics-04 to -24JIC 37° cone (74° included)
Inquire
JIC 37° bulkhead union, straight with long threaded body and locknut

Bulkhead Union JIC

Indus Hydraulics37-conebulkhead
Inquire
Category image · Hoses & Fittings
Category image · Hoses & Fittings

Questions we get asked

About this range

01What does the dash size mean?
The nominal size in sixteenths of an inch: a -08 is 8/16, or 1/2 inch nominal. On a JIC end it identifies the thread — a -08 is 3/4-16 UNF — rather than the bore exactly.
02Can I tighten a JIC joint harder to stop a leak?
No. The seal is the flare, and over-tightening damages it. Make the joint up by flats from finger tight, and if a correctly made joint still weeps, inspect the flare for scratches or distortion.
03Is JIC the same as SAE 45° flare?
No. They share threads on several sizes, but JIC seals on a 37° flare and SAE 45° on a 45° flare. A joint mixing the two may hold briefly, then leak.
04Why choose a JIC × SAE O-ring boss adapter rather than JIC × NPT for a port?
Because an O-ring boss seals on an elastomer O-ring, not on the thread, so it can be remade without losing engagement and, in adjustable form, aimed in any direction. An NPT end seals by thread interference, is rated lower than the O-ring boss in larger sizes, and goes deeper every time it is remade. Note that an O-ring boss end uses the same UN thread as the JIC end of the same dash size: tell them apart by the O-ring at the shoulder.
05How is a JIC bulkhead adapter fitted through a panel?
The long threaded body passes through a hole in the panel and is clamped by the bulkhead locknut, which tightens against the panel rather than sealing anything. Size the hole for the thread with a small clearance and keep the panel within the thickness the body can take. Hold the body while tightening the locknut, then make up the lines on each side by flats as for any JIC joint.
06How do I blank off a JIC line or port?
Use a JIC plug in a female swivel nut and a JIC swivel cap on a male end; both seal on the 37° flare in the same way as a working joint. Make them up by flats from finger tight like any JIC connection, not harder. For a port rather than a hose or tube end, blank it with a plug for that port type, such as an O-ring boss or BSP plug.
07What types of JIC adapter are there?
JIC adapters are 37° flare fittings with UN/UNF threads. The range covers JIC to JIC, NPT, BSP, BSPT, metric and SAE O-ring boss, as straight connectors, swivels, 45° and 90° elbows, tees, crosses, bulkheads, plugs and caps.
08What sizes do JIC adapters come in?
Threads start at 7/16-20, with dash sizes -04 to -24 on the 45° elbows and -04 to -20 on the bulkheads. Some are manufacturer-stated up to 345 bar (5,004 psi). The size table on this page lists each adapter.