Skip to content

Drilling & Workover Systems

51 SKUs2 brands

Showing 1–48 of 51 SKUs

Pulsation dampener section drawing: charging valve, gauge, stabilizer plate, diaphragm, bottom plate and gasket

Oteco Pulsation Dampener Diaphragms & Parts — K-10, K-20

OtecoPulsation dampener diaphragm and partsK-10, K-20
Inquire
Oteco premium wing-guided mud pump valve with polyurethane insert, its spring and a full-open seat

Oteco Mud Pump Valves & Seats — Wing-Guided, Full-Open, API 6 & 7

OtecoContinental Emsco, Gardner Denver, Ideco, National, OPI-Gist, Oilwell, Skytop Brewster pumpsAPI 6 and API 7 series
Inquire
Oteco piston assemblies showing the steel hub, bore and retainer the parts in this listing fit

Oteco Mud Pump Piston Hubs, Retainer Plates & Snap Rings

OtecoSeries A, B, K, LFabric-reinforced rubber or bonded polyurethane on a steel hub
Inquire
Oteco premium piston with black fabric-backed rubber and red lip seal on a steel hub, beside a urethane piston

Oteco Mud Pump Piston Rubbers & Replacement Kits

OtecoDuplex and triplex mud pumps, API-design pistonsFabric-reinforced rubber or bonded polyurethane on a steel hub
Inquire
Oteco premium bonded urethane piston for triplex mud pumps, yellow polyurethane on a steel hub

Oteco Single-Acting Mud Pump Pistons — Premium & Bonded Urethane

OtecoTriplex mud pumps (single-acting pistons), API-designMud pump piston, single acting
Inquire
Oteco mud pump pistons: yellow bonded urethane piston above a black premium rubber piston, steel hubs

Oteco Double-Acting Mud Pump Pistons

OtecoSeries A, B, K, LDuplex mud pumps (double-acting pistons), API-design
Inquire
Oteco jack-up shock pad, black rubber layers bonded between steel plates with corner fixing holes

Oteco Shock Pads for Jack-Up Rig Jacking Systems

OtecoShock pad, laminated rubber and steelFormulated rubber bonded between corrosion-resistant steel plates
Inquire
Oteco forged impact box end wrenches in three sizes, painted, 6-point box

Oteco Impact Box Wrenches, 5/8" to 2-1/2" Stud

OtecoImpact box end wrench, 6-pointForged steel
Inquire
Oteco six-roller wireline guide, the unit the hanging assembly supports in the derrick

Oteco Wireline Guide Hanging Assemblies

OtecoOteco G-10-S and G-102-S guides in beam and angle derricksGF-31 to GF-38
Inquire
Oteco G-20-H wireline turnback assembly drawing: frame casting, roller, shaft, bearings, U-bolt and base

Oteco G-20 Wireline Turnback Assemblies & Parts

OtecoG-20-H, G-20-NSteel and ductile castings; nitrile (NBR) rollers
Inquire
Oteco G-10-S six-roller wireline guide, cast frame with black nitrile rollers

Oteco Wireline Guides & Rollers — G-10, G-102, BJ Roliguide

OtecoSteel and ductile castings; nitrile (NBR) rollersWireline to 1-1/2" (G-10-S) or 2" (G-102-S); BJ Roliguide units
Inquire
Oteco balancing strap clamp with U-bolt and nuts, bronze-coloured casting

Oteco Elevator Balancing Straps & Tong Pull-Back Straps

OtecoRubber strap, steel clamp and U-boltCentre-latch elevators; manual tongs
Inquire
Oteco mud guard assembly drawing showing end seals, side seals, metal seal brackets and discharge hose

Oteco Mud & Oil Guard Seals and Spare Parts

OtecoMud guard spare partsMG-500, MG-600, MG-800
Inquire
Oteco mud guard opened on its hinge with end seals and discharge hose, MG-800 range

Oteco MG-800 Mud Guard, 2-3/8" to 6-5/8" drill pipe (shorty to 7-1/4")

OtecoMud Guard (mud bucket)Steel body; neoprene (CR) or nitrile (NBR) seals
Inquire
Oteco mud guard opened on its hinge, steel halves with end seals and discharge hose

Oteco MG-500 Oil Guard, 1" to 3-1/2" tubing

Oteco1" to 3-1/2" tubingSteel body; neoprene (CR) or nitrile (NBR) seals
Inquire
Oteco hexagonal kelly wiper, red nitrile ring with hex bore and bonded metal ring

Oteco Hexagonal Kelly Wipers, 8-3/8" and 10"

OtecoHexagonal kellys 2-1/2" to 6"Kelly wiper
Inquire
Oteco square kelly wiper, black rubber ring with square bore and bonded metal reinforcement

Oteco Square Kelly Wipers, 8-3/8" and 10"

OtecoNatural rubber (black), nitrile (red), neoprene; bonded metal ringSquare kellys 2-1/2" to 6"
Inquire
Oteco handle-bar pipe wiper, steel reinforced natural rubber with two handles

Oteco Oval and Handle-Bar Pipe Wipers

OtecoNatural rubber (black), nitrile (red), neopreneBlind (no bore) or 2-3/8" to 6-5/8" pipe
Inquire
Oteco single solid pipe wiper, black natural rubber disc with hard core and centre bore

Oteco Single Pipe Wipers, Hard and Soft Core

OtecoBlind (no bore) or 1" to 6-5/8" pipePipe wiper
Inquire
Oteco double pipe wiper disc, the rap-a-round version opens to wrap around the drill pipe

Oteco Double Split Rap-a-Round Pipe Wipers

Oteco2-3/8" to 11" pipeNatural rubber (black), nitrile (red), neoprene
Inquire
Oteco double pipe wiper moulded disc with centre bore, the split version is slit to the bore

Oteco Double Split Pipe Wipers

OtecoNatural rubber (black), nitrile (red), neoprenePipe wiper
Inquire
Oteco double pipe wiper, red nitrile, thick moulded disc with centre bore

Oteco Double Solid Pipe Wipers

OtecoPipe wiper2-3/8" to 6-5/8" pipe
Inquire
Oteco swivel washpipe, hardened steel tube with drive lugs, representative image

Oteco Swivel Washpipe & Packing — Other Swivels

OtecoSwivels identified by Oteco part numberHardened steel washpipe; elastomer packing rings
Inquire
Oteco swivel washpipe, hardened steel tube with drive lugs — representative of the Gardner-Denver range

Oteco Washpipe & Packing for Gardner-Denver Swivels

OtecoHardened steel washpipe; elastomer packing ringsSwivel washpipe and packing
Inquire
Oteco swivel washpipe, hardened steel tube with drive lugs — representative of the King range

Oteco Washpipe & Packing for King Swivels

OtecoSwivel washpipe and packingHardened steel washpipe; elastomer packing rings
Inquire
Oteco swivel washpipe, hardened steel tube with drive lugs — representative of the Oilwell range

Oteco Washpipe & Packing for Oilwell Swivels

OtecoSwivel washpipe and packingHardened steel washpipe; elastomer packing rings
Inquire
Oteco swivel washpipe, hardened steel tube with drive lugs — representative of the Ideco range

Oteco Washpipe & Packing for Ideco Swivels

OtecoIdeco swivels: DSS-300, SS-150, SS-250, SS-300, SS-625, SS-830, TL-120, TL-200, TL-300, TL-400, TL-500, TL-650, TSS-150, TSS-250 and TSS-300Swivel washpipe and packing
Inquire
Oteco swivel washpipe, hardened steel tube with drive lugs — representative of the National range

Oteco Washpipe & Packing for National Swivels

OtecoSwivel washpipe and packingHardened steel washpipe; elastomer packing rings
Inquire
Oteco swivel washpipe, hardened steel tube with drive lugs — representative of the Gray range

Oteco Washpipe & Packing for Gray Swivels

OtecoHardened steel washpipe; elastomer packing ringsGray swivels: A, B, B-41, B-44, B-44-M (Type A) Quick Change, C, F and FM
Inquire
Oteco swivel washpipe, hardened steel tube with drive lugs — representative of the Emsco range

Oteco Washpipe & Packing for Emsco Swivels

OtecoEmsco swivels: AE-4 (New Style), L-200, L-300, L-400, L-650, LA-200, LA-300, LA-400, LB-140, LB-200, LB-300, LB-400, LB-500 and LB-650Hardened steel washpipe; elastomer packing rings
Inquire
Oteco swivel washpipe, hardened steel tube with drive lugs — representative of the Skytop Brewster range

Oteco Washpipe & Packing for Skytop Brewster Swivels

OtecoSkytop Brewster swivels: 3-S, 3-TS, 6-BX, 6-HD, 6-S, 6-SBX, 6-SX, 7-BX, 7-SX, 8-BX, 8-SX and 9-SXHardened steel washpipe; elastomer packing rings
Inquire
Oteco 180° standpipe gooseneck manifold fitting drawing with dimension letters

Oteco 180° Standpipe Goosenecks, 4 in, 5 in

Oteco180° standpipe gooseneck4", 5"
Inquire
Oteco 160° standpipe gooseneck manifold fitting drawing with dimension letters

Oteco 160° Standpipe Goosenecks, 3 in, 4 in, 5 in

Oteco160° standpipe gooseneck3", 4", 5"
Inquire
Oteco 90° long sweep ell with 2 inch outlet manifold fitting drawing with dimension letters

Oteco 90° Long-Sweep Ells with 2" Outlet, 4 in, 5 in

Oteco4", 5"90° long sweep ell with 2 inch outlet
Inquire
Oteco 90° long sweep ell manifold fitting drawing with dimension letters

Oteco 90° Long-Sweep Ells, 2 in, 3 in, 4 in, 5 in, 6 in

Oteco2", 3", 4", 5", 6"90° long sweep ell
Inquire
Oteco 45° long sweep ell manifold fitting drawing with dimension letters

Oteco 45° Long-Sweep Ells, 2 in, 3 in, 4 in, 5 in

Oteco45° long sweep ell2", 3", 4", 5"
Inquire
Oteco long sweep full flow tee manifold fitting drawing with dimension letters

Oteco Long-Sweep Full Flow Tees, 2 in, 3 in, 4 in, 5 in

OtecoLong sweep full flow tee2", 3", 4", 5"
Inquire
Oteco long sweep full flow cross manifold fitting drawing with dimension letters

Oteco Long-Sweep Full Flow Crosses, 2 in, 3 in, 4 in, 5 in

Oteco2", 3", 4", 5"Long sweep full flow cross
Inquire
Category image · Drilling & Workover Systems
Red standpipe manifold with several mud gate valves on interconnected high-pressure piping

Standpipe Manifold, 5,000 and 7,500 psi

Indus HydraulicsHammer union, flangedStandpipe (mud) manifold
Inquire
Category image · Drilling & Workover Systems
Category image · Drilling & Workover Systems
Category image · Drilling & Workover Systems

Questions we get asked

About this range

01What does a mud degasser do?
It removes gas entrained in the mud returning from the well, restoring the mud's density so it keeps controlling well pressure, and venting the gas safely. Large gas volumes are first taken out by a mud-gas separator; the degasser removes the fine gas that remains.
02How is a mud pump package rated?
By input horsepower — for example a 1,600 HP triplex. Liner size then trades pressure against rate: a smaller liner gives higher pressure at lower flow, a larger liner the opposite.
03What is a mud manifold?
The high-pressure valve and pipe assembly that routes discharge from the mud pumps to the standpipe and the rig floor, letting the crew line pumps up, isolate them and divert flow. It is built with gate valves to the system's working pressure.
04What is a liquid mud plant?
An onshore base facility that mixes, stores and conditions drilling fluid, often oil-based mud, and supplies it to rigs by truck or vessel, so mud is prepared in bulk rather than at each rig.
05Mud tank or workover tank — what is the difference?
Mud tanks hold and condition the active drilling fluid with agitators and solids-control equipment. Workover tanks hold completion brine and fluids during workover and are often insulated, with a recirculation manifold.
06Are drilling and workover systems built to order?
Yes. Each is built to the capacity, pressure, footprint and certification you specify, and the lead time is confirmed at quotation.