Valves and the dampener are the two parts of a mud pump fluid end that decide how smoothly it delivers. The valves open and close on every stroke; the dampener smooths the pressure pulses leaving the pump. Both are wear items, and both are ordered by pump model. Pump and dampener makers named here are trademarks of their owners; Oteco parts are replacement parts made to fit that equipment, and Indus Hydraulics is not affiliated with those makers.
/01The Oteco wing-guided valve and full-open seat.
Oteco’s premium wing-guided valve and full-open seat are made in API 6 and API 7 series for most popular mud pumps. The valve is a uni-body with a snap-on polyurethane insert, so there are no snap rings, plates or keepers to fail, and the body is carburised for longer life and lower maintenance. Oteco says the seating angle and full-open seat improve flow through the seat and pass lost-circulation material better than conventional valves and seats, and that the full-open seat is easier to service in valve-over-valve fluid ends and carries a heavy bearing load.
Oteco also makes premium stem-guided valves and seats, with an extra-wide metal-to-metal seal and a serrated upper face. Our listing does not carry stem-guided part numbers; tell us which guide style you are replacing and we confirm the current part number for your pump.
/02Reading the selection table.
For each pump model the Oteco table gives a valve, a seat and a spring. Part numbers read O-U6VL-1 or O-U7VL-1 for the valve (6 or 7 series), O-6SL-1, O-6SL-2, O-7SL-1 or O-7SL-2 for the seat, and O-5710-15, -84, -90, -91 or -93 for the spring. Most pumps take O-5710-90; the Continental Emsco D, F and FA/FB models and the National K models take their own springs. Examples from the table:
| Pump | Valve | Seat | Spring |
|---|---|---|---|
| Continental Emsco D-125 | O-U6VL-1 | O-6SL-1 | O-5710-15 |
| Continental Emsco D-375 | O-U7VL-1 | O-7SL-1 | O-5710-84 |
| Continental Emsco F-1000 | O-U6VL-1 | O-6SL-1 | O-5710-91 |
| Gardner Denver PZ-10 | O-U7VL-1 | O-7SL-1 | O-5710-90 |
| Ideco T-1300 | O-U7VL-1 | O-7SL-1 | O-5710-90 |
| National 8-P-80 | O-U6VL-1 | O-6SL-2 | O-5710-90 |
| National 12-P-160 | O-U7VL-1 | O-7SL-2 | O-5710-90 |
| National K-180 | O-U7VL-1 | O-7SL-1 | O-5710-93 |
| Skytop Brewster B-1000-T | O-U6VL-1 | O-6SL-1 | O-5710-90 |
Spares are listed separately: the polyurethane insert (OU-23310 for API 6, OU-23315 for API 7) and seat puller heads (OP1700-6 for API 6 seats, OP1700-7 for API 7 seats). Replacing only the insert on a sound valve body is possible, since the insert snaps on. Fluid-end pistons are the other half of the job; see mud pump pistons explained.
/03What a pulsation dampener does.
A dampener on the pump discharge holds a gas charge on one side of a flexible diaphragm. As the pump pulses, the diaphragm moves and the gas absorbs the peaks, so the pressure downstream is steadier. The diaphragm is the part that flexes on every stroke, which is why it is the part you replace. Oteco makes most replacement parts for Hydril and Mattco K-10 (10 gallon) and K-20 (20 gallon) dampeners; the listing also includes a diaphragm for the Continental Emsco PD-55.
Oteco diaphragms are moulded in one piece down to the bottom flange, with a metal insert moulded into the bottom so the rubber cannot extrude into the bottom-flange connection.
/04Choosing NBR or HNBR and the pressure range.
Oteco makes diaphragms for 1,500, 3,000, 5,000 and 7,500 psi service. The listed part numbers are narrower: nitrile (NBR) diaphragms to 5,000 psi for both the K-10 and K-20, and a hydrogenated nitrile (HNBR) diaphragm to 7,500 psi for the K-20 only. There is no listed HNBR diaphragm for the K-10. The stabilizer, stabilizer plate, screw and lock washer are needed only for the 1,500 psi range.
| Part | K-10 | K-20 |
|---|---|---|
| Diaphragm, NBR, 0 to 5,000 psi | IH-OTC-230110 (14 lb, 6.4 kg) | IH-OTC-230010 (22 lb, 10 kg) |
| Diaphragm, HNBR, 0 to 7,500 psi | Not listed | IH-OTC-230012 (22 lb, 10 kg) |
| Diaphragm stabilizer (1,500 psi range) | IH-OTC-230120 | IH-OTC-230020 |
| Stabilizer plate | IH-OTC-230030 | IH-OTC-230030 |
| Pressure gauge, 316 stainless, 0 to 6,000 psi | IH-OTC-230060 | IH-OTC-230060 |
| Charging valve with bull plug, brass | IH-OTC-230070 | IH-OTC-230070 |
| Bottom plate gasket | IH-OTC-230080 | IH-OTC-230080 |
| Bottom plate, 4-1/16 in 5,000 psi R-39 | Not listed | IH-OTC-123754 (79 lb, 35.8 kg) |
Pick a rating at or above your pump discharge pressure. Note that the stainless gauge reads to 6,000 psi, so on a 7,500 psi duty it will not show the full range. Send the dampener model from the plate and the working pressure, and we confirm the diaphragm.
/05Pre-charge with nitrogen only.
Pre-charge the dampener with nitrogen only, to the pressure the pump maker specifies for the operating pressure. Never use air or oxygen. Oxygen with oil and rubber under pressure is a fire and explosion hazard, and air contains it. Check the pre-charge on the gauge before the pump starts and inspect the diaphragm whenever the bottom plate comes off. Oteco gives no replacement interval for diaphragms; follow the pump maker’s manual and your own records.
Common questions
- Which spring goes with which valve?
- The spring depends on the pump model, not only the series. In the Oteco table O-5710-15 is for Continental Emsco D-125 and D-225, O-5710-84 for D-375, O-5710-91 for the Emsco F series, O-5710-93 for National K-180, K-280 and K-380, and O-5710-90 for most others.
- Can I order a valve without the seat?
- Yes, the valve, seat, spring, insert and puller heads are each listed. Oteco notes that each valve must be used with its matching full-open spring, so check the spring when you change the valve.
- Is there a K-10 diaphragm for 7,500 psi?
- Not among the part numbers we list. The HNBR diaphragm to 7,500 psi is listed for the K-20 only. Oteco makes diaphragms across 1,500 to 7,500 psi, so send the model and pressure and we check.
- Why nitrogen and not air?
- Air contains oxygen, which is dangerous with oil and rubber under pressure. Oteco states nitrogen only, to the pump maker’s specified pre-charge.
Valves, seats and dampener parts
IH-OTC-VALVES-SEATSOteco Mud Pump Valves & Seats — Wing-Guided, Full-Open, API 6 & 7Oteco
IH-OTC-DAMPENEROteco Pulsation Dampener Diaphragms & Parts — K-10, K-20Oteco
IH-OTC-PST-DAOteco Double-Acting Mud Pump PistonsOteco
IH-OTC-PST-SAOteco Single-Acting Mud Pump Pistons — Premium & Bonded UrethaneOteco




