A planetary gearbox does not fail from heat the way a hose does. It fails slowly: the oil thins, the film between the gear teeth gets thinner, the oil oxidises faster, seals harden, and the first sign is a leak or a noise months later. In the Gulf, where summer ambient is above the +40 °C most makers rate their standard units for, the oil and the duty decide how long the gearbox lasts. The guidance below follows Dinamic Oil’s catalogues and maintenance manuals.
/01Which oil.
Dinamic Oil specifies a mechanical transmission oil with EP (extreme pressure) additives in viscosity class ISO VG 220 to ISO VG 320 to ISO 3448, chosen on the ambient temperature and the actual running temperature of the gearbox. Mineral EP oils such as Shell Omala S2 G, Mobilgear XMP or Castrol Alpha SP are listed; for very high ambient temperatures or wide temperature swings, the recommendation is a synthetic oil — Omala S4 GX, Mobilgear SHC or Alphasyn EP class. The heavier grade is the usual choice for a gearbox that works through a Gulf summer.
/02When to change it.
| Unit | First oil change | Then | Routine checks |
|---|---|---|---|
| Planetary gearbox, winch driveHighlighted | 150 h | By oil temperature, at most every 2 years | Every 3 months: level, leaks, play, noise, temperature |
| Hydraulic hoisting winch | 150 h | Once a year | Oil level every 250 h, rope daily |
| P series winch (grease) | — | Grease every 250 h | Rope daily |
| Towing / recovery winch | 500 h | Once a year | Oil level every 250 h, rope daily |
The first change matters more than any other: it removes the wear particles from running-in. Check the magnetic plugs at the same time — a little fine paste is normal, flakes or chips are not. The oil-temperature table in the manual shortens the interval as the running temperature rises, which is why a gearbox in the Gulf is often on a shorter cycle than the same model in Europe.
/03When it runs too hot.
Every gearbox has a thermal power: the power it can transmit continuously before the oil reaches its limit. It depends on the mounting and the ambient air. If the transmitted power is above it — a mixer, conveyor or travel drive running all shift in summer — the cure is not a different oil but more cooling: an independent oil/water or oil/air cooling unit (Dinamic Oil’s dissipate up to 50 kW) or a larger frame. Vertical gearboxes in continuous duty can overheat the oil at the top; an external expansion tank keeps them filled. Keep the housing and cooling paths clean: dust on a gearbox is insulation.
/04Storing spares.
A spare gearbox in a container yard is not a spare. Dinamic Oil’s manual calls for dry storage between −5 °C and +30 °C, on timber, not stacked, with anti-corrosion grease on flanges and shafts after two months; over six months, fill it with service oil, fit the breather on top and turn the input over periodically (release the brake with a hand pump). Seals begin to deteriorate after six months on the shelf, so renew them before a long-stored unit goes into service.
Common questions
- Can I mix mineral and synthetic oil?
- Not as a rule. Drain and flush when changing type; some synthetic bases are not compatible with mineral oil or with every seal material.
- Does the brake need its own oil?
- Multi-disc brakes on Dinamic Oil gearboxes hold a small volume of oil that is changed with the gearbox oil.
- How do I know the oil is overheating?
- Darkening oil, a burnt smell, a housing too hot to touch and weeping seals. Measure the running temperature and compare it with the manual’s table.
- Is the catalogue oil quantity exact?
- No. It varies with the ratio, input and output. Fill to the level plug, run for a few minutes and check again.
- Where do I find the intervals for my unit?
- In the use and maintenance manual attached to each Dinamic Oil product page on our site.
Gearboxes and winch drives
IH-DO-REDinamic Oil RE In-Line Planetary Gearboxes — 1,780 Nm to 198 kNmDinamic Oil
IH-DO-GBDinamic Oil GB Heavy-Duty Planetary Gearboxes — 281 kNm to 3.62 MNmDinamic Oil
IH-DO-WDDinamic Oil WD Planetary Winch Drives — 18.1 kNm to 400 kNm FEM TorqueDinamic Oil
IH-DO-SLRDinamic Oil RE Slewing Gearboxes — 4,350 to 163,500 Nm, Pinion OutputDinamic Oil



