Dinamic Oil RE Slewing Gearboxes — 4,350 to 163,500 Nm, Pinion Output

Dinamic Oil RE slewing gearboxes: 14 frame sizes, nominal output torque 4,350 to 163,500 Nm, pinion or splined output, static brakes for open or closed circuits. Built in Italy. From Indus Hydraulics, authorised Dinamic Oil distributor, UAE.
Key features
- Product type: Slewing gearbox (planetary)
- Series: Dinamic Oil RE
- Execution: Planetary, reinforced output support for pinion drive
- Reduction stages: 2, 3
- Output torque: T2 FEM 4,350 to 163,500 Nm (M5, 15 rpm)
- Reduction ratio: 13 to 332:1
- Motor / input: Hydraulic (orbital, axial piston) or electric motor
- Brake: Static negative: low opening pressure or dry version
- Type approval: ABS PDA 22-2218009-1 / 25-0346164 (specific RE/RA 810–1520 thruster builds); others on demand
- Product type
- Slewing gearbox (planetary)
- Series
- Dinamic Oil RE
- Execution
- Planetary, reinforced output support for pinion drive
- Reduction stages
- 2, 3
- Type approval
- ABS PDA 22-2218009-1 / 25-0346164 (specific RE/RA 810–1520 thruster builds); others on demand
Product description
RE slewing gearboxes are Dinamic Oil's planetary drives for slewing rings: an RE gearset on a reinforced output support that carries the radial load of the pinion meshing with the ring gear. Fourteen frame sizes, RE 240 to RE 8010, cover nominal output torques up to 4,350 Nm on the smallest frame and 163,500 Nm on the largest, in two or three stages, for mobile, offshore and deck cranes, aerial platforms, excavators, concrete pumps, container gantries and azimuth thrusters.
Indus Hydraulics is an authorised Dinamic Oil distributor and supplies direct from Dinamic Oil's factory in Bomporto, Italy.
Ratings
The table gives each size's nominal output torque T2 FEM — Dinamic Oil's figure for F.E.M. class M5 (L2-T5) at 15 rpm output, an indicative value confirmed per application — and the ratio range for each number of stages. The output support has its own static and dynamic torque limits in the catalogue: the lower of the support limit and the gearset's T2max governs, and the static limit must never be exceeded.
Supports, shafts and pinions
Each size comes with one or more output supports, listed in the table by Dinamic Oil's support code — the eccentric ones (marked ecc) let the pinion-to-ring backlash be set — and a choice of splined or cylindrical output shaft or a pinion. The table lists the supports and the catalogue's pinion range for each size (module and number of teeth); pinions are splined on, or cut integral with the shaft, and pinions outside the catalogue are made to the ring-gear data you send.
Approvals
ABS product design assessments 22-2218009-1-PDA and 25-0346164-PDA cover specific RE and RA 810, 1020 and 1520 builds with pinion output for azimuth-thruster steering, valid to February 2027 and November 2030. Design approval by DNV, ABS, RINA, Bureau Veritas, Lloyd's Register or CCS is available on demand for other builds.
Inputs, brakes and lubrication
Inputs for hydraulic (orbital or axial piston) and electric motors are the same as Dinamic Oil's planetary gearbox range. Static negative brakes come in a low-opening-pressure version for closed-loop circuits and a dry version for high-speed motors. Oil or grease lubrication is available; standard ambient range up to +40 °C.
Options and accessories
- Brakes: static negative brakes in a low-opening-pressure version for closed-loop circuits and a dry version for high-speed motors. See brakes for planetary gearboxes.
- Inputs: hydraulic orbital or axial piston motors, or electric motors, through the planetary range's adapters.
- Outputs: splined or integral pinions, splined or cylindrical shafts; eccentric supports for backlash adjustment; pinions made to your ring-gear data.
- Lubrication: oil or grease.
Identification
| Parameter | Value |
|---|---|
| Product type | Slewing gearbox (planetary) |
| Series | Dinamic Oil RE |
| Execution | Planetary, reinforced output support for pinion drive |
Performance
| Parameter | Value |
|---|---|
| Reduction stages | 2, 3 |
| Output torque | T2 FEM 4,350 to 163,500 Nm (M5, 15 rpm) |
| Reduction ratio | 13 to 332:1 |
Construction
| Parameter | Value |
|---|---|
| Motor / input | Hydraulic (orbital, axial piston) or electric motor |
| Brake | Static negative: low opening pressure or dry version |
| Output / mounting | Pinion (splined or integral) or splined / cylindrical shaft; flanged or eccentric support |
| Lubrication | Oil or grease |
Compliance
| Parameter | Value |
|---|---|
| Rating basis | F.E.M. M5 (L2-T5) at 15 rpm, indicative |
| Type approval | ABS PDA 22-2218009-1 / 25-0346164 (specific RE/RA 810–1520 thruster builds); others on demand |
Supply
| Parameter | Value |
|---|---|
| Made in | Italy (Dinamic Oil S.p.A., Bomporto) |
| Supply | Authorised distributor, direct from the factory |
Shipping & lead time
Sizes & part numbers
14 sizes- Indus part no.IH-DO-SLR-240
- Description
- RE 240
- Output torque (Nm)
- 4,350
- Mount
- Supports DBS, Tecc
- Shaft
- Pinion m6–14, z9–18; splined or cylindrical shaft
- Ratio
- 2-stage 13–39; 3-stage 46–281
- Indus part no.IH-DO-SLR-310
- Description
- RE 310
- Output torque (Nm)
- 5,420
- Mount
- Supports NR, NR3, Tecc, T6, T8, T18, DBS
- Shaft
- Pinion m5–14, z10–22; splined or cylindrical shaft
- Ratio
- 2-stage 13–54; 3-stage 44–321
- Indus part no.IH-DO-SLR-510
- Description
- RE 510
- Output torque (Nm)
- 10,800
- Mount
- Supports NR, NR3, Tecc, T6, T8, T18, DBS
- Shaft
- Pinion m5–14, z10–22; splined or cylindrical shaft
- Ratio
- 2-stage 13–54; 3-stage 44–321
- Indus part no.IH-DO-SLR-610
- Description
- RE 610
- Output torque (Nm)
- 12,400
- Mount
- Supports T18, DBS, DBS2
- Shaft
- Pinion m8–14, z10–20; splined or cylindrical shaft
- Ratio
- 2-stage 14–34; 3-stage 50–245
- Indus part no.IH-DO-SLR-810
- Description
- RE 810
- Output torque (Nm)
- 15,800
- Mount
- Supports Tecc, TRecc
- Shaft
- Pinion m8–14, z12–18; splined or cylindrical shaft
- Ratio
- 2-stage 13–51; 3-stage 53–314
- Indus part no.IH-DO-SLR-1020
- Description
- RE 1020 (ratio range confirmed per order)
- Output torque (Nm)
- 22,800
- Mount
- Supports TR, T6ecc, DBS, Z, DBS4, DBT
- Shaft
- Pinion m8–18, z10–18; splined or cylindrical shaft
- Ratio
- 3-stage 53–314
- Indus part no.IH-DO-SLR-1520
- Description
- RE 1520
- Output torque (Nm)
- 33,500
- Mount
- Supports Tecc, DBS, Z, DBT
- Shaft
- Pinion m8–20, z10–18; splined or cylindrical shaft
- Ratio
- 2-stage 15–47; 3-stage 51–278
- Indus part no.IH-DO-SLR-2000
- Description
- RE 2000
- Output torque (Nm)
- 41,300
- Mount
- Supports Tecc, DBS, Z, DBT
- Shaft
- Pinion m8–20, z10–18; splined or cylindrical shaft
- Ratio
- 2-stage 14–39; 3-stage 48–202
Show all 14 sizesShow fewer sizes
- Indus part no.IH-DO-SLR-2520
- Description
- RE 2520 (ratio range confirmed per order)
- Output torque (Nm)
- 48,100
- Mount
- Supports DBS, Z, Z1
- Shaft
- Pinion m12–20, z10–16; splined or cylindrical shaft
- Ratio
- 2-stage 14–47
- Indus part no.IH-DO-SLR-3000
- Description
- RE 3000
- Output torque (Nm)
- 65,500
- Mount
- Supports DBS, Z, Z1
- Shaft
- Pinion m12–20, z10–16; splined or cylindrical shaft
- Ratio
- 2-stage 14–32; 3-stage 51–242
- Indus part no.IH-DO-SLR-3510
- Description
- RE 3510
- Output torque (Nm)
- 71,800
- Mount
- Supports Z2, Z3, DBS1, HR
- Shaft
- Pinion m14–25, z11–21; splined or cylindrical shaft
- Ratio
- 2-stage 14–44; 3-stage 49–332
- Indus part no.IH-DO-SLR-4800
- Description
- RE 4800
- Output torque (Nm)
- 105,000
- Mount
- Supports Z2, Z3, DBS1, HR
- Shaft
- Pinion m14–25, z11–21; splined or cylindrical shaft
- Ratio
- 2-stage 13–32; 3-stage 47–242
- Indus part no.IH-DO-SLR-6010
- Description
- RE 6010
- Output torque (Nm)
- 122,000
- Mount
- Supports Z1, Z4
- Shaft
- Pinion m16–25, z12–24; splined or cylindrical shaft
- Ratio
- 2-stage 14–40; 3-stage 64–252
- Indus part no.IH-DO-SLR-8010
- Description
- RE 8010
- Output torque (Nm)
- 163,500
- Mount
- Supports Z1, Z4
- Shaft
- Pinion m16–25, z12–24; splined or cylindrical shaft
- Ratio
- 2-stage 15–29; 3-stage 57–200
Description — What this part number is, as the manufacturer lists it. Output torque — Rated output torque, as the manufacturer publishes it. A circuit is limited by its lowest-rated component. The page states which rating it is. Mount — Mounting flange or pattern, as published. Shaft — Drive shaft, as published. Ratio — Reduction ratio, or the range of ratios the model is built in, as published.
What is the Dinamic Oil RE Slewing Gearboxes used for?▾
How do I read a Dinamic Oil model such as RE 1520?▾
Which sizes and torques do the Dinamic Oil RE Slewing Gearboxes cover?▾
What is T2 FEM on the Dinamic Oil RE Slewing Gearboxes?▾
Which torque limit governs on the Dinamic Oil RE Slewing Gearboxes?▾
What brakes and lubrication do the Dinamic Oil RE Slewing Gearboxes use?▾
Do the Dinamic Oil RE Slewing Gearboxes carry a class approval?▾
What pinions and supports fit the Dinamic Oil RE Slewing Gearboxes?▾
Can the pinion backlash of the Dinamic Oil RE Slewing Gearboxes be adjusted?▾
How do the RE slewing gearboxes compare with the GB range?▾
Are the Dinamic Oil RE Slewing Gearboxes genuine Dinamic Oil units and can you export them?▾
Do you keep the Dinamic Oil RE Slewing Gearboxes in stock in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog
Written about this part
Specification & standards
Slewing drive selection: torque, pinion, backlash and brake for crane and platform slewing
A slewing gearbox drives a pinion into a slewing ring, and the pinion is often what limits it. How to size the torque, read the support limits, set the backlash and choose the brake for a crane, aerial platform or thruster slewing drive.
3 min read
Gulf operating conditions
Planetary gearbox oil in hot climates: grade, change intervals and heat in Gulf duty
Most planetary gearboxes and winches are rated for an ambient of +40 °C — a figure the Gulf passes for months every year. Which oil to use, when to change it, how to tell when a gearbox is running too hot, and how to store spares so they are serviceable when needed.
4 min read
Specification & standards
DNV type approval for crane and winch gearboxes: what it covers and what it does not
A DNV type approval or an ABS product design assessment on a gearbox saves weeks on a classed crane or winch — if you know what it covers. What type approval, PDA and works recognition mean, what they leave to the project, and which Dinamic Oil drives carry them.
3 min read

