Skip to content
Stainless steel fittings

Stainless hose barbs, push-on and crimp hose fittings: what each is for and what limits them

A stainless hose barb will outlast every hose pushed onto it — which is exactly why the hose, not the barb, decides the pressure. Barbed, push-on (push-lock) and crimp hose ends in 316: how each holds the hose, Parker’s published push-on hose limits of 200 to 350 psi, why push-on hose needs no clamp, and when a low-pressure line should be a crimped assembly instead.

Written by
Ayush Bhatia, Director
Published
Reading
4 min · 3 sections
Share
Stainless barbed and push-on hose fittings in clear and black hose on a food-plant bench, with a hose clamp
Barbed ends are for low-pressure hose; the clamp and the hose set the limit.

At a glance

Key takeaways

  1. Three ways to hold a hose: a barb with a clamp, a push-on fitting gripped by its matching self-gripping hose, or a ferrule crimped over the hose.
  2. The hose sets the limit. Parker’s Push-Lok 801PLUS hose is rated 350 psi at -4/-6, 300 psi at -8 to -12 and 200 psi at -16, with a design factor of 4.
  3. Push-on fittings need no clamp — but only with hose designed for them; a plain hose on a push-on barb is a barbed joint with no clamp.
  4. Stainless ends are chosen for washdown, food, chemical and marine hose lines where brass or plated steel would corrode; the far end can be JIC, NPT or BSPP.
  5. Above a few hundred psi, or with pulsation, use a crimped hose assembly rated as a whole.

Figures verified · Push-on system behaviour and hose ratings from Parker’s Push-Lok brochure; ends and connections from our listings.

Not every hose in a plant is a hydraulic pressure line. Coolant, compressed air, washdown water, drains, returns, cleaning chemicals and sampling lines all run at low pressure — and in a food, chemical or marine plant all of them need ends that will not corrode. That is where stainless barbed and push-on fittings earn their place, as long as nobody mistakes them for a pressure fitting.

/01Barb, push-on or crimp.

How each stainless hose end holds the hose
EndHolds the hose byClamp?Typical use
Hose barbRidged shank inside the hoseYes — a hose clampWater, air, drains, transfer at low pressure
Push-on (push-lock)HighlightedBarb profile gripped by self-gripping hoseNo — with matching hoseAir, coolant, lubrication, return lines
Crimp fittingFerrule swaged over the hoseNoHydraulic pressure hose, rated as an assembly

Parker describes its Push-Lok range as "the self-grip hose system for low-pressure applications": the hose is designed to grip the fitting’s barb by itself, so no clamps or special tools are needed, and the fittings come in brass, steel and stainless with DIN, BSP, SAE, JIC and ORFS ends. The grip depends on the hose. Push a general rubber or PVC hose onto a push-on fitting and you have a barbed joint without a clamp.

/02What limits the pressure.

Parker Push-Lok 801PLUS hose, maximum working pressure (design factor 4)
SizeMax working pressureMinimum burst
-4, -6Highlighted350 psi (2.4 MPa)1,400 psi
-8, -10, -12300 psi (2.1 MPa)1,200 psi
-16200 psi (1.4 MPa)800 psi

Parker’s other push-on hoses — high-temperature water, phosphate ester, fire-resistant and others — carry working pressures from about 150 to 300 psi. No rating is published for the stainless push-on fitting on its own, because the hose fails first: an assembly is rated to the lower of the hose and its end. For a barbed hose with a clamp, rate it to the hose maker’s figure for clamped connections, and keep it well below that where the line can be knocked or pulled.

/03Stainless crimp fittings.

Where a hose line in a corrosive area does carry pressure, the answer is a stainless crimp fitting: a stem and ferrule swaged onto a matched hose to the crimp maker’s specification, rated with that hose as an assembly. Our stainless crimp ends have ORB male, NPT male swivel and tube-stub connections. They must be crimped to the dimension specified for the exact hose series — the fitting series and the hose series are a pair, not interchangeable parts.

Which stainless hose end?

  1. IfLow-pressure air, coolant or return line, matching push-on hose available?

    Push-on fitting, no clamp.

    IH-SS-PO-MJ
  2. IfWater, drain or transfer hose of any make, low pressure?

    Hose barb with a stainless clamp.

    IH-SS-HB-MP
  3. IfHydraulic pressure, pulsation or a line that must not blow off?

    Crimped assembly on a matched hose.

    IH-SS-T43-MOR

Common questions

What pressure can a push-on hose fitting take?
The hose decides. Parker’s Push-Lok 801PLUS hose is rated 350 psi at -4/-6, 300 psi at -8 to -12 and 200 psi at -16; its other push-on hoses are about 150–300 psi.
Do push-on hose fittings need clamps?
Not with hose designed for them — the hose grips the barb. On ordinary hose, a push-on fitting needs a clamp like any barb.
Why use stainless hose barbs?
For corrosion: washdown, food, chemical and marine lines where brass or plated steel would corrode or contaminate.
Can I use a hose barb on a hydraulic line?
Only on low-pressure lines such as drains and returns within the hose rating. Pressure lines need crimped or reusable assemblies.
What ends are available on stainless push-on fittings?
Ours come with 37° JIC male and female swivel, NPT male, male swivel and female swivel, and BSPP male and female swivel ends.

What we list

Stainless hose barbs, push-on hose fittings and stainless crimp hose fittings:

Stainless hose ends

Sources

  1. 1.Parker. Push-Lok Hoses and Fittings — the self-grip hose system for low-pressure applications (B4480-B176). ↗

What next

  1. 01
  2. 02
  3. 03

    Where stainless fittings like these go

    Stainless jobs are rarely one part: a process skid needs butt-weld fittings, flanges and threaded fittings in one grade, a hygienic line needs clamps, ferrules and gaskets that match, and an offshore hydraulic panel needs every adapter in 316 so nothing rusts next to it. We quote the whole list from the sizes, grades and end connections you send, keep 304 and 316 apart, and ship from Dubai as one consignment with the mill certificates the project asks for.

    Everything above ships from the same Dubai warehouse. If your destination is not listed, it is almost certainly still one we quote. See every export destination

Low-pressure hose in a corrosive area?

Send the hose, size, medium, pressure and end connection. We will quote stainless barbed, push-on or crimped ends to suit.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Stainless steel fittings

All articles in this topic
Polished 316L stainless hose fittings: BSP and JIC swivels, a flange head, a standpipe, a banjo, and stainless crimp ferrules

316L stainless hose fittings: when a hose end has to be stainless, and the forms available

6 min read

A stainless bite-type tube union with 24° cones, nuts and loose cutting rings, beside tube with a pre-set ring

Stainless DIN 2353 cutting-ring fittings (ISO 8434-1) and SAE flareless bite-type fittings

8 min read

Stainless O-ring hydraulic fittings with black O-rings on face and thread shoulder, including an adjustable 90° elbow

Stainless ORFS and ORB fittings: O-ring face seal and O-ring boss in 316

5 min read

Back to Blog