Skip to content
Hydraulic tools & bolting

Hydraulic pullers, presses and cutters: sizing a puller, choosing a press and cutting safely

Bearings, gears and couplings come off with a puller sized to the shaft; bushes and pins go in and out on a press; chain, cable, bar and bolts are cut cold rather than torched. Enerpac’s rule for puller capacity, the difference between Lock-Grip and Sync-Grip pullers, the press frames for a workshop, the limits on hydraulic cutters, and what comes in a ready-made cylinder and pump set.

Written by
Ayush Bhatia, Director
Published
Updated
Reading
4 min · 4 sections
Share
Three-jaw hydraulic puller on a gear and shaft, with an H-frame workshop press and a hydraulic chain cutter
Size the puller to the shaft, and check reach and spread before force.

At a glance

Key takeaways

  1. Enerpac sizes hydraulic pullers at 7 to 10 tons of capacity per inch of shaft diameter.
  2. Check reach (how far behind the part the jaws must go) and spread (how wide they must open) as well as force.
  3. Presses are chosen by frame and tonnage: arbor 5–30 t, workshop 10–75 t, H-frame 10–200 t in Enerpac’s range.
  4. Hydraulic cutters have hardness and material limits — a cable cutter is not a decommissioning cutter.
  5. A cylinder-pump set arrives ready to use: cylinder, two-speed pump, safety hose and calibrated gauge.

Figures verified · Sizing rules, capacities and limits from Enerpac catalogue E330.

Workshop hydraulics do three things that hand tools cannot do safely: pull a part off a shaft it has rusted onto, press a part into or out of a housing, and cut steel without a flame. The tools are simple; the mistakes are in sizing — a puller too small for the shaft, jaws that cannot reach behind the part, or a cutter asked to cut something harder than it is made for.

/01Pullers.

Enerpac puller sizing — hydraulic pullers
Shaft diameterPuller capacity
Up to 1"14 t
1"–2"24 t
2"–3.5"Highlighted36 t
3.5"–5.5"50 t

The rule behind the table: capacity in tons of 7 to 10 times the shaft diameter in inches. For a mechanical puller, Enerpac’s rule is a centre bolt at least half the shaft diameter.

  • Lock-Grip pullers (hydraulic LGH 10–64 t, mechanical LGM) lock the jaws to the part so they cannot slip off under load; LGH pullers spread up to 26 in and reach up to 16 in.
  • Sync-Grip pullers close all three jaws at the same time, so the puller self-centres on the part.
  • Master puller sets add cross-arms, bearing pullers and attachments for parts that jaws cannot hold.

Measure reach — from the jaw tips to the end of the shaft — and spread before ordering; a puller with the force but not the reach is no use.

/02Presses.

Enerpac press frames (10,000 psi)
FrameCapacityUse
A-Series arbor, C-clamp, bench frame5–30 tBench work: bushes, pins, small bearings
XLP bolted workshop pressHighlighted10–75 tGeneral workshop pressing
IP H-frame / IPR roll-frame10–200 t / 50–200 tHeavy pressing; roll frame moves the cylinder across the bed

/03Cutters.

Hydraulic cutters cut cold, which Enerpac contrasts with torching, grinding and sawing: minimal spark risk and low vibration. Each type has a limit:

  • Chain cutters (ECCE) cut up to Grade 100 chain, 1.25 in material, behind a transparent guard.
  • Wire and cable cutters (EWCH) cut cable of 3.54–7.09 in diameter up to 43 HRc.
  • Bar cutters cut round bar up to about 2 in; flat-bar cutters (EFBE) take bar up to 2.75 × 0.59 in.
  • Decommissioning cutters (EDCH) open 5.12–6.69 in and cut material up to 41 HRc — and Enerpac says not to use them on wire rope.

/04Cylinder and pump sets.

For general pushing, lifting and pressing jobs, a set saves matching parts: Enerpac’s SCR (5–100 t, 1.5–14.25 in stroke) and low-height SCL (5–50 t) sets each include a single-acting cylinder, a two-speed hand pump, a 6 ft safety hose and a calibrated gauge with adaptor. Maintenance sets add the spreaders, wedges and attachments for body and frame repair; pipe bender and punch sets use the same pump with different heads.

Common questions

What size hydraulic puller do I need?
Enerpac’s rule is 7 to 10 tons of capacity per inch of shaft diameter — about 36 tons for a 2–3.5 in shaft — with enough reach and spread for the part.
Lock-Grip or Sync-Grip puller?
Lock-Grip locks the jaws so they cannot slip off; Sync-Grip closes all jaws together so the puller centres itself. Both suit bearings and gears; choose by the part and access.
Can a hydraulic cutter cut wire rope?
A wire and cable cutter can, within its diameter and hardness limits. Enerpac’s decommissioning cutters must not be used on wire rope.
What comes in a cylinder and pump set?
A single-acting cylinder, a two-speed pump, a 6 ft safety hose and a calibrated gauge with its adaptor.

What we list

Pullers, presses, cutters, cylinder-pump and maintenance sets, and swing clamps:

Pullers, presses and cutters

IndustryMiningWorkshop pulling and pressing on heavy equipment.

Sources

  1. 1.Enerpac. Industrial Tools Catalog E330 (EN-US). ↗
MarketSupplying Peru from DubaiFreight, import documents and lead times for mining and processing operations in Peru.MarketSupplying Uzbekistan from DubaiFreight, import documents and lead times for mining and processing operations in Uzbekistan.

What next

  1. 01
  2. 02
  3. 03

    Where tools like these go

    A bolting or lifting job is planned around a shutdown window, and the tool has to arrive with everything it needs to work: the pump, twin hoses, sockets, reaction arms, gauges and the oil. We quote from the bolt size, torque or load and the access you have on site, list the whole kit so nothing is missing when the crew opens the case, and ship it from Dubai as one consignment ahead of the window.

    Everything above ships from the same Dubai warehouse. If your destination is not listed, it is almost certainly still one we quote. See every export destination

Need a puller, press or cutter?

Send the shaft diameter and the part’s size and position, the pressing force, or what has to be cut and how hard it is. We will quote the tool with its pump and hose.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Hydraulic tools & bolting

All articles in this topic
Portable hydraulic power unit with hoses to a breaker on broken concrete, a cut-off saw and a submersible pump

Hydraulic power tools: HTMA flow classes, power units and running tools off a machine

3 min read

Hydraulic bolt tensioners on a large offshore flange, with a nut splitter and wedge flange spreader on the deck

Bolt tensioning, nut splitters and flange tools: opening, aligning and closing a bolted joint

5 min read

Back to Blog