Skip to content
Stainless steel fittings

Stainless steel weld outlets: weldolet, threadolet and sockolet branch connections, and weld-on adapters

Cutting a full tee into a 6" stainless line to take a ½" drain wastes a weld, a fitting and a day. A weld outlet does it with one forged fitting welded onto the run. Butt-weld, socket-weld and threaded outlets to MSS SP-97, how they reinforce the hole, elbolets, latrolets and nipolets, and the weld-on adapters that put a hydraulic port on a tank or manifold.

Written by
Ayush Bhatia, Director
Published
Reading
4 min · 3 sections
Share
A stainless branch pipe rising from a saddle-shaped weld outlet on a larger pipe, with a threaded outlet further along
A branch outlet takes a smaller line off the run without cutting in a full tee.

At a glance

Key takeaways

  1. A weld outlet is a forged fitting welded onto the run pipe over a hole, to take a branch without cutting in a tee.
  2. MSS SP-97 covers integrally reinforced forged branch outlets; the fitting supplies the reinforcement the piping codes (B31.1, B31.3, B31.4, B31.8) require around the hole.
  3. The branch end decides the type: weldolet (butt weld), sockolet (socket weld, Class 3000/6000/9000), threadolet (NPT, Class 3000/6000).
  4. Elbolets sit on long-radius elbows for thermowells and instruments; latrolets make 45° laterals; nipolets are one-piece outlets for vents, drains and valve take-offs.
  5. The reinforcement depends on the run pipe wall, so order the outlet by run size, run schedule and branch size.

Figures verified · Outlet types, classes and reinforcement from Wermac’s summary of Bonney Forge data and MSS SP-97; weld-on adapters from our listings.

Every process line sprouts small branches — drains at low points, vents at high points, pressure and temperature tappings, sample points. On a large stainless run each could be a reducing tee, with two extra butt welds and a cut through the pipe. Most of them are instead a weld outlet: a contoured forging welded onto the outside of the pipe, with the branch connection already on it.

/01What an outlet does.

Cutting a hole in a pressure pipe weakens it; the piping codes require the metal removed to be replaced around the opening. A weld outlet carries that reinforcement in its own body. Wermac, quoting Bonney Forge, says these fittings meet the 100% reinforcement requirement of the applicable piping codes and are shaped to minimise stress concentration. The standard is MSS SP-97, integrally reinforced forged branch outlet fittings.

Because the reinforcement is sized against the run wall, an outlet is specified by the run pipe size and schedule as well as the branch size — the same ½" outlet is a different forging on a 2" Sch 10S run than on a 6" Sch 40S one.

/02The types.

Branch outlet types (Wermac, after Bonney Forge)
TypeBranch endTypical use
WeldoletHighlightedButt weld (bevelled), full-penetration branch weldThe most common outlet; branches on process lines
SockoletSocket weld, Class 3000, 6000 or 9000Small-bore welded branches
ThredoletNPT female thread, Class 3000 or 6000Gauges, plugs, threaded valves
ElboletButt weld, socket or thread, on a long-radius elbowThermowells and instruments at a bend
LatroletButt weld, socket or thread, at 45°Lateral connections
NipoletOne piece with a built-in nippleValve take-offs, drains and vents

Whether a given branch is a tee or an outlet is the piping class’s decision — most specifications carry a branch table that says which to use for each run and branch size. Socket-weld and threaded outlets follow the same class logic as ASME B16.11 fittings: see threaded and socket-weld fittings for what the class numbers mean.

/03Weld-on hydraulic adapters.

A different weld-on part does a similar job on hydraulic equipment: a 316 stainless body with a plain end to weld onto a tank, reservoir, manifold or pipe, and a hydraulic connection on the other — 37° JIC male or female swivel, ORFS female swivel, BSPP female swivel or NPT. They put a standard port where there was only plate or pipe, and the swivel versions let a hose or tube be connected without twisting it. Weld them with the same purge and L-grade care as any stainless weld, and keep welding heat away from any O-ring or seal on the fitting.

Common questions

What is a weldolet?
A forged branch outlet with a butt-weld branch end, welded onto a run pipe over a hole. It carries its own reinforcement under MSS SP-97 and is the most common type of outlet.
Weldolet or tee?
The piping class decides, usually through a branch table. Outlets are used for branches smaller than the run; tees for equal or near-equal branches.
What is the difference between a sockolet and a threadolet?
The branch end: a sockolet takes the branch pipe in a socket for a fillet weld (Class 3000, 6000 or 9000); a threadolet has an NPT female thread (Class 3000 or 6000).
How do I order a weld outlet?
By run pipe size and schedule, branch size, branch end type and class, and grade — for example 6" Sch 40S run × 1" Class 3000 threaded, 316.
What is an elbolet used for?
A branch on a long-radius elbow — usually a thermowell or instrument that needs to face into the flow.

What we list

Forged 304 and 316 butt-weld, socket-weld and threaded outlets, and 316 weld-on hydraulic adapters:

Weld outlets and weld-on adapters

Sources

  1. 1.Wermac. Olets — branch connections (after Bonney Forge). ↗
  2. 2.ASME B16.11 — Forged Fittings, Socket-Welding and Threaded, scope. ↗

What next

  1. 01
  2. 02
  3. 03

    Where stainless fittings like these go

    Stainless jobs are rarely one part: a process skid needs butt-weld fittings, flanges and threaded fittings in one grade, a hygienic line needs clamps, ferrules and gaskets that match, and an offshore hydraulic panel needs every adapter in 316 so nothing rusts next to it. We quote the whole list from the sizes, grades and end connections you send, keep 304 and 316 apart, and ship from Dubai as one consignment with the mill certificates the project asks for.

    GCC & Middle East

    West & Central Africa

    Everything above ships from the same Dubai warehouse. If your destination is not listed, it is almost certainly still one we quote. See every export destination

Adding branches to a stainless line?

Send the run size and schedule, branch sizes and end types, class and grade. We will quote the outlets to match.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Stainless steel fittings

All articles in this topic
Polished 316L stainless hose fittings: BSP and JIC swivels, a flange head, a standpipe, a banjo, and stainless crimp ferrules

316L stainless hose fittings: when a hose end has to be stainless, and the forms available

6 min read

Stainless barbed and push-on hose fittings in clear and black hose on a food-plant bench, with a hose clamp

Stainless hose barbs, push-on and crimp hose fittings: what each is for and what limits them

4 min read

A stainless bite-type tube union with 24° cones, nuts and loose cutting rings, beside tube with a pre-set ring

Stainless DIN 2353 cutting-ring fittings (ISO 8434-1) and SAE flareless bite-type fittings

8 min read

Back to Blog