Stainless Steel Rigging Screw — Swage and Fork Ends, M4–M36

Stainless Steel Rigging Screw (European type), in 113 sizes, M4 to M36. Indus part numbers, manufacturer's test certificate.
Key features
- Product type: Stainless Steel Rigging Screw
- Pattern / standard: European type
- Size range: M4 to M36
- Size range
- M4 to M36
- Material
- AISI 316 stainless steel turnbuckle rigging screw
- Finish
- Polished
Product description
Turnbuckles and rigging screws tension guy lines, stays and tie-downs and take up slack. Built to the European pattern. AISI 316 stainless steel turnbuckle rigging screw, polished.
Sizes and ratings
113 sizes, M4 to M36. Minimum breaking load 500 to 43,000 kg. Available as: jaw and swage stud, swage stud and swage stud, machined fork and fork, machined fork and terminal, toggle and swage stud, toggle and toggle, body only. Every size has its own Indus part number in the table below, with the loads in the unit the manufacturer rates them in.
The lettered dimensions in the table refer to the dimension drawing for each type, shown with this product.
Manufacturer's data
- Machining.
Choosing a size
Choose on WLL with the end fittings you will use — hook ends rate lower than eyes or jaws — and on the take-up length you need. Lock the body once tensioned so it cannot back off.
Ordering
Quote the Indus part number from the size table, or send the size and rating you need. Each consignment ships with the manufacturer's test certificate; say on the RFQ if your site needs anything more.
Identification
| Parameter | Value |
|---|---|
| Product type | Stainless Steel Rigging Screw |
| Pattern / standard | European type |
| Sizes | 113 |
Dimensions
| Parameter | Value |
|---|---|
| Size range | M4 to M36 |
Performance
| Parameter | Value |
|---|---|
| Minimum breaking load | 500 to 43,000 kg |
Construction
| Parameter | Value |
|---|---|
| Material | AISI 316 stainless steel turnbuckle rigging screw |
| Finish | Polished |
Compliance
| Parameter | Value |
|---|---|
| Certification | Manufacturer's test certificate |
Shipping & lead time
Sizes & part numbers
113 sizes- Indus part no.IH-LR-TB-SSRSSFE-M4-JSS
- Size
- M4
- Type
- Jaw and swage stud
- Rope size
- 2 mm
- Min breaking load (kg)
- 500
- A (mm)
- 5.5
- D (mm)
- 4
- D1 (mm)
- 2.2
- H (mm)
- 8
- L1 (mm)
- 125
- L2 (mm)
- 150
- D2 (mm)
- 4.8
- L3 (mm)
- 24
- Weight (kg/100 pcs)
- 3.3
- Indus part no.IH-LR-TB-SSRSSFE-M5-JSS
- Size
- M5
- Type
- Jaw and swage stud
- Rope size
- 2 mm
- Min breaking load (kg)
- 800
- A (mm)
- 6.5
- D (mm)
- 5
- D1 (mm)
- 2.2
- H (mm)
- 10
- L1 (mm)
- 155
- L2 (mm)
- 215
- D2 (mm)
- 5.5
- L3 (mm)
- 32
- Weight (kg/100 pcs)
- 5
- Indus part no.IH-LR-TB-SSRSSFE-M5-JSS-2
- Size
- M5
- Type
- Jaw and swage stud
- Rope size
- 2.5 mm
- Min breaking load (kg)
- 800
- A (mm)
- 6.5
- D (mm)
- 5
- D1 (mm)
- 2.7
- H (mm)
- 10
- L1 (mm)
- 155
- L2 (mm)
- 215
- D2 (mm)
- 5.5
- L3 (mm)
- 32
- Weight (kg/100 pcs)
- 5
- Indus part no.IH-LR-TB-SSRSSFE-M5-JSS-3
- Size
- M5
- Type
- Jaw and swage stud
- Rope size
- 3.2 mm
- Min breaking load (kg)
- 800
- A (mm)
- 6.5
- D (mm)
- 5
- D1 (mm)
- 3.5
- H (mm)
- 10
- L1 (mm)
- 160
- L2 (mm)
- 220
- D2 (mm)
- 6.35
- L3 (mm)
- 39
- Weight (kg/100 pcs)
- 4.6
- Indus part no.IH-LR-TB-SSRSSFE-M6-JSS
- Size
- M6
- Type
- Jaw and swage stud
- Rope size
- 3 mm
- Min breaking load (kg)
- 1,250
- A (mm)
- 7.5
- D (mm)
- 6
- D1 (mm)
- 3.3
- H (mm)
- 10
- L1 (mm)
- 175
- L2 (mm)
- 245
- D2 (mm)
- 6.35
- L3 (mm)
- 39
- Weight (kg/100 pcs)
- 8
- Indus part no.IH-LR-TB-SSRSSFE-M6-JSS-2
- Size
- M6
- Type
- Jaw and swage stud
- Rope size
- 3.2 mm
- Min breaking load (kg)
- 1,250
- A (mm)
- 7.5
- D (mm)
- 6
- D1 (mm)
- 3.5
- H (mm)
- 10
- L1 (mm)
- 175
- L2 (mm)
- 245
- D2 (mm)
- 6.35
- L3 (mm)
- 39
- Weight (kg/100 pcs)
- 8
- Indus part no.IH-LR-TB-SSRSSFE-M6-JSS-3
- Size
- M6
- Type
- Jaw and swage stud
- Rope size
- 4 mm
- Min breaking load (kg)
- 1,250
- A (mm)
- 7.5
- D (mm)
- 6
- D1 (mm)
- 4.3
- H (mm)
- 10
- L1 (mm)
- 185
- L2 (mm)
- 255
- D2 (mm)
- 7.5
- L3 (mm)
- 45
- Weight (kg/100 pcs)
- 8.5
- Indus part no.IH-LR-TB-SSRSSFE-M8-JSS
- Size
- M8
- Type
- Jaw and swage stud
- Rope size
- 4 mm
- Min breaking load (kg)
- 1,300
- A (mm)
- 11
- D (mm)
- 8
- D1 (mm)
- 4.3
- H (mm)
- 11
- L1 (mm)
- 200
- L2 (mm)
- 275
- D2 (mm)
- 7.5
- L3 (mm)
- 45
- Weight (kg/100 pcs)
- 14
Show all 113 sizesShow fewer sizes
Size — Nominal size as the manufacturer states it. Type — Manufacturer type within the size. Rope size — Rope diameter the sheave is made for. Min breaking load — Minimum breaking load. A test figure — never lift to it. A — Dimension A on the manufacturer dimension drawing. D — Dimension D on the manufacturer dimension drawing. D1 — Dimension D1 on the manufacturer dimension drawing. H — Dimension H on the manufacturer dimension drawing. L1 — Dimension L1 on the manufacturer dimension drawing. L2 — Dimension L2 on the manufacturer dimension drawing. D2 — Dimension D2 on the manufacturer dimension drawing. L3 — Dimension L3 on the manufacturer dimension drawing. Weight — Weight of 100 pieces, as published. Ask us for the dimension drawing if you need it stamped.
WLL is the most the part may carry in service. Proof and breaking loads are test figures — never lift to them. Each load is shown in the unit the manufacturer rates the part in, and a size ships with the manufacturer’s test certificate.
This range is published with a breaking load only, not a working load limit. Tell us the duty before using it to lift, and we will confirm a rating or recommend a rated part.
What is the Stainless Steel Rigging Screw — Swage and Fork Ends and where is it used?▾
How do I read Stainless Steel Rigging Screw — Swage and Fork Ends part numbers such as IH-LR-TB-SSRSSFE-M4-JSS?▾
Which sizes does the Stainless Steel Rigging Screw — Swage and Fork Ends come in?▾
How do I choose the right size of Stainless Steel Rigging Screw — Swage and Fork Ends?▾
What load rating does the Stainless Steel Rigging Screw — Swage and Fork Ends carry?▾
What material and finish does the Stainless Steel Rigging Screw — Swage and Fork Ends have?▾
What standard and certificate apply to the Stainless Steel Rigging Screw — Swage and Fork Ends?▾
Which parts connect to the Stainless Steel Rigging Screw — Swage and Fork Ends?▾
How do I install and check the Stainless Steel Rigging Screw — Swage and Fork Ends?▾
How does the Stainless Steel Rigging Screw — Swage and Fork Ends compare with the Stainless Steel Rigging Screw, Jaw and Jaw?▾
Do you ship the Stainless Steel Rigging Screw — Swage and Fork Ends outside the UAE?▾
Is the Stainless Steel Rigging Screw — Swage and Fork Ends available from stock in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog
Written about this range
Lifting & rigging
How to choose and tension a turnbuckle: end fittings, ratings, locking and inspection
A turnbuckle looks simple — two threads and a body — but the end fittings change its rating by half, an unlocked one can spin itself loose, and it is built for straight pulls only. How to choose the end fittings, body and size, read the rating, tension it properly, lock it, and know when to take it out of service.
4 min read
Lifting & rigging
DIN 1480 vs DIN 1478 turnbuckles: open frame or closed body?
DIN 1480 and DIN 1478 are the two German standards behind most metric turnbuckles in the Gulf. One is a forged open frame you can see the threads through; the other a closed tube that hides them. What each standard covers, how their ratings compare size for size, how the end fittings change things, and which to choose for bracing, guying, lashing and fencing.
3 min read
Lifting & rigging
Turnbuckle types: hook, eye and jaw ends, open and closed bodies, and what each can carry
A turnbuckle is only as strong as its weakest end, and that is usually the hook: on our US drop-forged range a 1/2″ hook end is rated 1,500 lb against 2,200 lb for eye or jaw ends. Here is how end fittings and body types change the rating, which standards cover what, and how to keep a turnbuckle from unwinding.
6 min read








