Commercial Turnbuckle — Eye and Eye, Cast Steel
Commercial Turnbuckle (DIN 1480), in 15 sizes, M5 to M42, WLL 0.995 to 59.15 kN. Indus part numbers, manufacturer's test certificate.
Key features
- Product type: Commercial Turnbuckle
- Pattern / standard: DIN 1480
- Size range: M5 to M42
- Working load limit: 0.995 to 59.15 kN
- Size range
- M5 to M42
- Working load limit
- 0.995 to 59.15 kN
- Material
- Malleable iron
- Finish
- Self colour, electro-galvanized
Product description
Turnbuckles and rigging screws tension guy lines, stays and tie-downs and take up slack. Made to DIN 1480. Malleable iron, self colour, electro-galvanized.
Sizes and ratings
15 sizes, M5 to M42. Working load limit 0.995 to 59.15 kN. Minimum breaking load 3.978 to 236.6 kN. Every size has its own Indus part number in the table below, with the loads in the unit the manufacturer rates them in.
The lettered dimensions in the table refer to the dimension drawing shown with this product.
Choosing a size
Choose on WLL with the end fittings you will use — hook ends rate lower than eyes or jaws — and on the take-up length you need. Lock the body once tensioned so it cannot back off.
Ordering
Quote the Indus part number from the size table, or send the size and rating you need. Each consignment ships with the manufacturer's test certificate; say on the RFQ if your site needs anything more.
Identification
| Parameter | Value |
|---|---|
| Product type | Commercial Turnbuckle |
| Pattern / standard | DIN 1480 |
| Sizes | 15 |
Dimensions
| Parameter | Value |
|---|---|
| Size range | M5 to M42 |
Performance
| Parameter | Value |
|---|---|
| Working load limit | 0.995 to 59.15 kN |
| Minimum breaking load | 3.978 to 236.6 kN |
Construction
| Parameter | Value |
|---|---|
| Material | Malleable iron |
| Finish | Self colour, electro-galvanized |
Compliance
| Parameter | Value |
|---|---|
| Certification | Manufacturer's test certificate |
Shipping & lead time
Sizes & part numbers
15 sizes| Indus part no. | Size | WLL (kN) | Min breaking load (kN) | h (mm) | L1 (mm) | L2 (mm) | L3 (mm) | Ø1 (mm) | Ø2 (mm) |
|---|---|---|---|---|---|---|---|---|---|
| IH-LR-TB-CTEEC-M5 | M5 | 0.994 | 3.978 | 5 | 70 | 58 | 35 | 15 | 8 |
| IH-LR-TB-CTEEC-M6 | M6 | 1.46 | 5.85 | 6 | 110 | 80 | 55 | 19 | 9 |
| IH-LR-TB-CTEEC-M8 | M8 | 2.66 | 10.66 | 8 | 110 | 84 | 55 | 24 | 11 |
| IH-LR-TB-CTEEC-M10 | M10 | 4.22 | 16.9 | 9 | 125 | 105 | 63 | 31 | 15 |
| IH-LR-TB-CTEEC-M12 | M12 | 6.04 | 24.18 | 11 | 125 | 115 | 68 | 35 | 17 |
| IH-LR-TB-CTEEC-M14 | M14 | 8.19 | 32.76 | 13.5 | 140 | 121 | 70 | 36 | 18 |
| IH-LR-TB-CTEEC-M16 | M16 | 11.5 | 46.02 | 14 | 170 | 150 | 85 | 48 | 22 |
| IH-LR-TB-CTEEC-M20 | M20 | 17.5 | 70.2 | 17 | 200 | 163 | 100 | 52 | 24 |
| IH-LR-TB-CTEEC-M22 | M22 | 22 | 88.14 | 19 | 220 | 185 | 110 | 60 | 27 |
| IH-LR-TB-CTEEC-M24 | M24 | 25.4 | 101.9 | 21 | 255 | 205 | 128 | 66 | 27 |
| IH-LR-TB-CTEEC-M27 | M27 | 35.1 | 133.6 | 22 | 255 | 216 | 128 | 71 | 34 |
| IH-LR-TB-CTEEC-M30 | M30 | 40.6 | 162.5 | 23 | 255 | 230 | 128 | 71 | 31 |
| IH-LR-TB-CTEEC-M33 | M33 | 50.5 | 202 | 25 | 255 | 253 | 128 | 81 | 39 |
| IH-LR-TB-CTEEC-M36 | M36 | 59.1 | 236.6 | 28 | 295 | 270 | 148 | 95 | 43 |
| IH-LR-TB-CTEEC-M42 | M42 | — | — | 32 | 330 | 300 | 170 | 113 | 48 |
Size — Nominal size as the manufacturer states it. WLL — Working load limit — the most the part may carry in service, as the manufacturer rates it. Min breaking load — Minimum breaking load. A test figure — never lift to it. h — Dimension h on the manufacturer dimension drawing. L1 — Dimension L1 on the manufacturer dimension drawing. L2 — Dimension L2 on the manufacturer dimension drawing. L3 — Dimension L3 on the manufacturer dimension drawing. Ø1 — Dimension Ø1 on the manufacturer dimension drawing. Ø2 — Dimension Ø2 on the manufacturer dimension drawing. Ask us for the dimension drawing if you need it stamped.
WLL is the most the part may carry in service. Proof and breaking loads are test figures — never lift to them. Each load is shown in the unit the manufacturer rates the part in, and a size ships with the manufacturer’s test certificate.
What sizes does the commercial turnbuckle come in?▾
What is the working load limit?▾
Why do hook-end turnbuckles have a lower WLL?▾
Do the parts come with a test certificate?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 126 destinations
Engineers viewing this also looked at
DIN 1478 Turnbuckle — Galvanized
DIN 1480 Turnbuckle
Die-Cast Zinc Turnbuckle
Galvanized Rigging Screw, Closed Body
Hamburger Lashing Turnbuckle
Turnbuckle — Italian Type
JIS Frame Turnbuckle, Eye and Hook
