R1 1SN Single Wire Braid Hydraulic Hose
Single-wire braid medium-pressure hydraulic hose for general industrial and mobile hydraulics. 1/4" – 2" (DN6 – DN51).
Key features
- Applicable Standard: SAE 100R1AT / EN 853 1SN
- Construction Type: 1-wire-braid
- Bore Size Range: 1/4" – 2" (DN6 – DN51)
- Max Working Pressure: 225 bar
- Min Burst Pressure: 900 bar
- Min Operating Temperature: -40 °C
- Max Operating Temperature: 100 °C
- Reinforcement: One layer of high-tensile steel wire braid
- Applicable Standard
- SAE 100R1AT / EN 853 1SN
- Construction Type
- 1-wire-braid
- Bore Size Range
- 1/4" – 2" (DN6 – DN51)
- Max Working Pressure
- 225 bar
- Min Burst Pressure
- 900 bar
- Min Operating Temperature
- -40 °C
Product description
The R1 1SN Single Wire Braid Hydraulic Hose Single-wire braid medium-pressure hydraulic hose for general industrial and mobile hydraulics. Conforms to SAE 100R1AT / EN 853 1SN.
Construction
- Tube: Synthetic rubber (NBR), oil-resistant
- Reinforcement: One layer of high-tensile steel wire braid
- Cover: Synthetic rubber, abrasion- and weather-resistant, MSHA-accepted, wrapped
Performance
Working pressures up to 225 bar at -04, falling to 40 bar at -32, with a minimum burst of 900 bar (safety factor 4:1). Continuous service from -40°C to 100°C, with the upper limit reduced for aggressive fluids — ask for a fluid compatibility chart if needed.
Applications
- General-purpose hydraulics on machine tools and power units
- Mobile equipment — agricultural, light construction, materials handling
- Hydraulic return-line and pilot-line service
Compliance
- SAE 100R1AT
- EN 853 1SN
- MSHA-accepted cover
Also available in
The same SAE 100R1AT grade is stocked in Eaton Aeroquip and Parker Hannifin in addition to the Eaton Winner reference shown here. Tell us your brand preference on the RFQ and we will quote accordingly.
Companion grades
For higher pressures see R2 2SN. For tighter routing see the 1SC compact equivalent.
Identification
| Parameter | Value |
|---|---|
| Applicable Standard | SAE 100R1AT / EN 853 1SN |
| Construction Type | 1-wire-braid |
Dimensions
| Parameter | Value |
|---|---|
| Bore Size Range | 1/4" – 2" (DN6 – DN51) |
| Min Bend Radius | 100–630 mm by bore (100 mm at -04, 630 mm at -32) |
| Outside Diameter Range | 13.2–63.6 mm (-04 to -32) |
Performance
| Parameter | Value |
|---|---|
| Max Working Pressure | 225 bar |
| Min Burst Pressure | 900 bar |
| Working Pressure Range | 225 bar at -04 down to 40 bar at -32 |
| Safety Factor | 4:1 |
| Min Operating Temperature | -40 °C |
| Max Operating Temperature | 100 °C |
Construction
| Parameter | Value |
|---|---|
| Reinforcement | One layer of high-tensile steel wire braid |
| Tube (Inner) Material | Synthetic rubber (NBR), oil-resistant |
| Cover Material | Synthetic rubber, abrasion- and weather-resistant, MSHA-accepted |
| Cover Finish | wrapped |
Compliance
| Parameter | Value |
|---|---|
| Conductivity | non-conductive |
Commercial
| Parameter | Value |
|---|---|
| Sold By | per-metre |
Shipping & lead time
What standard does this hose comply with?▾
What is the maximum working pressure?▾
What temperature range is supported?▾
What bore sizes are available?▾
Is this hose conductive?▾
What end fittings are recommended?▾
How is this hose sold?▾
What is the typical lead time?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 126 destinations
From the blog
Written about this part
Specification & standards
Hose dash sizes: −04 to −48, and the one grade where the number means something else
A dash size is sixteenths of an inch of bore. Except on SAE 100R5, where −08 is a 10 mm bore rather than 12 mm — because R5 is sized on tube outside diameter. Here is the full conversion, and where it breaks.
5 min read
Specification & standards
SAE 100R types: the numbers are a catalogue, not a ranking
R6 is rated 28 bar. R2AT is rated 400 bar. The higher number is fourteen times weaker. Here is what each SAE 100R designation actually specifies, and why the sequence tells you nothing about strength.
7 min read
Specification & standards
EN 853, 856 and 857 against SAE 100R: what actually cross-references
Two of these pairings are real and printed on the same hose. Several of the equivalences circulating in the trade are not. Here is which is which, and what to do about the grades that have no counterpart.
5 min read
Engineers viewing this also looked at
R12 Four-Spiral High-Pressure Hose
R13 Multi-Spiral Very-High-Pressure Hose
R14 PTFE Hydraulic Hose
R15 Six-Spiral Ultra-High-Pressure Hose
R17 Compact High-Pressure Hose
R2 2SN Double Wire Braid Hydraulic Hose
R3 Two-Fibre Braid Hydraulic Hose
