R3 Two-Fibre Braid Hydraulic Hose
Hydraulic HosesEx-stock · delivery in 3 days
VIEW 01·R3 Two-Fibre Braid Hydraulic Hose
Two-fibre-braid low-to-medium-pressure hydraulic hose for return-line and low-pressure delivery. 1/4" – 1-1/2" (DN6 – DN38).
Key features
- Applicable Standard: SAE 100R3
- Construction Type: textile-braid
- Bore Size Range: 1/4" – 1-1/2" (DN6 – DN38)
- Max Working Pressure: 85 bar
- Min Burst Pressure: 340 bar
- Min Operating Temperature: -40 °C
- Max Operating Temperature: 100 °C
- Reinforcement: Two textile braids (high-tensile yarn)
- Applicable Standard
- SAE 100R3
- Construction Type
- textile-braid
- Bore Size Range
- 1/4" – 1-1/2" (DN6 – DN38)
- Max Working Pressure
- 85 bar
- Min Burst Pressure
- 340 bar
- Min Operating Temperature
- -40 °C
Ships in 24h
Order before 14:00 GST · Jebel Ali
24-month warranty
Manufacturer-backed · genuine parts
Engineering support
A real applications engineer
Product description
The R3 Two-Fibre Braid Hydraulic Hose Two-fibre-braid low-to-medium-pressure hydraulic hose for return-line and low-pressure delivery. Conforms to SAE 100R3.
Construction
- Tube: Synthetic rubber (NBR), oil-resistant
- Reinforcement: Two textile braids (high-tensile yarn)
- Cover: Synthetic rubber, weather-resistant, wrapped
Performance
Working pressures up to 85 bar at the smallest bore, with a minimum burst of 340 bar (safety factor 4:1). Continuous service from -40°C to 100°C, with the upper limit reduced for aggressive fluids — ask for a fluid compatibility chart if needed.
Applications
- Return-line service on hydraulic systems
- Low-pressure delivery and tank lines
- Light-duty agricultural and industrial hydraulics
Compliance
- SAE 100R3
Also available in
The same SAE 100R3 grade is stocked in Eaton Aeroquip and Parker Hannifin in addition to the Eaton Winner reference shown here. Tell us your brand preference on the RFQ and we will quote accordingly.
Companion grades
For higher pressures step up to R1 1SN (single wire braid). For lower-pressure air/water applications see R6.
Identification
| Parameter | Value |
|---|---|
| Applicable Standard | SAE 100R3 |
| Construction Type | textile-braid |
Dimensions
| Parameter | Value |
|---|---|
| Bore Size Range | 1/4" – 1-1/2" (DN6 – DN38) |
| Min Bend Radius | per size table |
Performance
| Parameter | Value |
|---|---|
| Max Working Pressure | 85 bar |
| Min Burst Pressure | 340 bar |
| Safety Factor | 4:1 |
| Min Operating Temperature | -40 °C |
| Max Operating Temperature | 100 °C |
Construction
| Parameter | Value |
|---|---|
| Reinforcement | Two textile braids (high-tensile yarn) |
| Tube (Inner) Material | Synthetic rubber (NBR), oil-resistant |
| Cover Material | Synthetic rubber, weather-resistant |
| Cover Finish | wrapped |
Compliance
| Parameter | Value |
|---|---|
| Conductivity | non-conductive |
Commercial
| Parameter | Value |
|---|---|
| Sold By | per-metre |
Shipping & lead time
Lead TimeEx-stock from Dubai — delivered within 3 working days in the UAE. Export orders ship on the lane stated for the destination.
OriginMade in China
What standard does this hose comply with?▾
It conforms to SAE 100R3.
What is the maximum working pressure?▾
Up to 85 bar at the smallest bore, scaling down at larger bores. Exact figure depends on inner diameter — request a size-specific datasheet on the RFQ.
What temperature range is supported?▾
-40°C to 100°C continuous service. Aggressive fluids (phosphate-ester, water-glycol, certain biodegradables) reduce the upper limit; ask for a fluid compatibility chart.
What bore sizes are available?▾
1/4" – 1-1/2" (DN6 – DN38). Common sizes are ex-stock; less common bores have a short lead time.
Is this hose conductive?▾
Non-conductive cover. The reinforcement carries continuity but is sleeved by the cover — safe for routing near energised circuits per most plant standards.
What end fittings are recommended?▾
Standard hydraulic fittings — JIC 37°, ORFS, BSP, NPT, and metric 24° flat-face — are crimped on this grade. Specify your termination on the RFQ and we will quote with a matched ferrule and crimp die.
How is this hose sold?▾
Per metre cut-to-length, or as a full coil. Add the bore size, length, and any fitting requirements to your RFQ; we will quote inclusive of crimping where applicable.
What is the typical lead time?▾
Common sizes are ex-stock from our Dubai warehouse. Less common bores or full coils typically ship within 7 working days.
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 126 destinations
From the blog
Written about this part
RELATED · OFTEN PAIRED WITH
Engineers viewing this also looked at
IH-HOSE-R5
R5 Textile-Cover Single Wire Braid Hose
Parker Hannifin
IH-HOSE-R6
R6 Single Fibre Braid Low-Pressure Hose
Eaton Winner
IH-HOSE-2SC
2SC Compact Two Wire Braid Hose
Indus Hydraulics
IH-HOSE-4SH
4SH Four-Spiral Heavy-Duty Hydraulic Hose
Indus Hydraulics
IH-HOSE-4SP
4SP Four-Spiral Hydraulic Hose
Indus Hydraulics
IH-HOSE-R1-1SC
R1 1SC Compact Single Wire Braid Hose
Indus Hydraulics
IH-HOSE-R1-1SN
R1 1SN Single Wire Braid Hydraulic Hose
Eaton Winner
IH-HOSE-R12
IH-HOSE-R12
R12 Four-Spiral High-Pressure Hose
Indus Hydraulics