Skip to content
Anchor chain & mooring

Anchor chain wear limits: the 12% rule and when to renew a length

Anchor chain wears where links rub against each other and the windlass. Classification societies allow the mean diameter to fall 12% below nominal before a length must be renewed. The minimum diameter for every size from 12.5 to 162 mm, how to measure, and the other defects that condemn a length.

Written by
Ayush Bhatia, Director
Published
Updated
Reading
4 min · 4 sections
Share
Gloved hands measuring a worn stud link anchor chain link with outside calipers where links rub together
Class rules allow a link to wear 12% below its nominal diameter; measure at the crown, where links rub.

At a glance

Key takeaways

  1. Class societies allow the mean diameter of an anchor chain link to wear to 88% of its nominal size — a 12% reduction — before the length must be renewed.
  2. For 76 mm chain the minimum mean diameter is 66.88 mm; for 50 mm it is 44 mm.
  3. Wear concentrates where links bear on each other and on the cable lifter, so measure there, not on the straight sides.
  4. Wear is not the only reason to renew: cracks, bent or stretched links and loose or missing studs condemn a length too.
  5. Renew by the length: replace the worn 27.5 m shot and its joining shackle, ordered to the same size and grade.

Figures verified · Minimum diameters computed from the 12% class society (IACS) rule as tabled by a chain stockist. Measurement practice and condemning defects are general guidance — the class surveyor decides.

Every time the anchor is weighed, each link grinds against its neighbours and against the pockets of the cable lifter, and over years the bar wears thin where it bears. Strength falls with the square of the remaining diameter, so a little wear matters. That is why the classification societies set a limit, and why a surveyor will put calipers on your chain at every special survey.

/01Minimum mean diameter by size.

Minimum mean diameter at 12% wear (mm)
Nominal diameterMinimum mean diameter
12.511.00
1412.32
1614.08
17.515.40
1916.72
20.518.04
2219.36
2421.12
2622.88
2824.64
3026.40
3228.16
3429.92
3631.68
3833.44
4035.20
4236.96
4438.72
4640.48
4842.24
5044.00
5245.76
5447.52
5649.28
5851.04
6052.80
6254.56
6456.32
6658.08
6859.84
7061.60
7364.24
7666.88
7868.64
8171.28
8473.92
8776.56
9079.20
9280.96
9583.60
9785.36
10088.00
10289.76
10592.40
10794.16
11197.68
114100.32
117102.96
120105.60
122107.36
124109.12
127111.76
130114.40
132116.16
137120.56
142124.96
147129.36
152133.76
157138.16
162142.56

/02Measuring a worn link.

The limit is on the mean diameter, so a single reading is not enough. In general practice:

  • Find the most worn part of the link — usually the inside of the crown, where it bears on the next link, and the areas that ride in the cable lifter pockets.
  • Clean off scale and growth, then take two caliper readings across the bar at right angles to each other.
  • Average them: that is the mean diameter to compare with the table.
  • Measure several links along each length, concentrating on the shots that work hardest — the ones nearest the anchor and those that sit on the windlass at anchor.

The class surveyor decides how many links and where; record the readings by shot so the trend can be followed from survey to survey.

/03Other reasons to renew.

A length can be condemned before it reaches the wear limit. A surveyor will look for:

  • cracks, especially at the flash-butt weld and around the stud;
  • links that are bent, twisted or visibly stretched;
  • studs that are loose, cracked or missing;
  • deep pitting or gouges;
  • joining shackles and swivels that are worn, distorted or seized, or Kenter shackles whose taper pins and lead plugs are missing.

The 5% elongation limit in a chain’s factory proof test is not an in-service limit — see anchor chain testing.

/04Renewing a length.

Worn chain is replaced by the 27.5 m length. Order the replacement to the same nominal diameter, grade and type, with a new Kenter shackle or joining shackle and, where the join needs them, end and enlarged links. The certificate for the new length goes into the ship’s file with the old ones. If a whole cable is near the limit, compare a full renewal with a higher grade at a smaller size — see equipment number.

Common questions

How much wear is allowed on anchor chain?
Generally 12% of the nominal diameter, measured as the mean diameter of the most worn part of the link.
What is the minimum diameter for 76 mm anchor chain?
66.88 mm.
Where does anchor chain wear most?
Where links bear on each other at the crowns, and where they ride in the cable lifter, mostly in the shots nearest the anchor.
Do I have to renew the whole cable?
No. Worn or damaged lengths are replaced individually, to the same size and grade, with new joining shackles.
Does the wear limit apply to mooring chain?
Offshore mooring chain has its own inspection and wear criteria under its mooring integrity plan and the class rules; this page covers ship anchor chain.

Replacement lengths and joining parts

What next

  1. 01
  2. 02

Lengths condemned at survey?

Send the size, grade, number of lengths and the survey date. We will quote certified replacement lengths and joining shackles for delivery before the ship sails.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Anchor chain & mooring

All articles in this topic
Back to Blog