Skip to content
Anchor chain & mooring

Equipment number: how a ship’s anchors and anchor chain are sized

Classification rules size a ship’s anchors and chain from a single figure, the equipment number. What it represents, how to read the equipment table to find anchor mass, total chain length and chain diameter in each grade, and why a high-holding-power anchor and a higher chain grade change the answer.

Written by
Ayush Bhatia, Director
Published
Updated
Reading
5 min · 3 sections
Share
Two anchor windlasses on a ship's forecastle with stud link chain running through stoppers into the hawse pipes
Anchor mass, chain length and chain size all come from one figure in the class rules: the equipment number.

At a glance

Key takeaways

  1. The equipment number is one figure, worked out under the class rules from a ship’s size and the area it shows to wind and current.
  2. The equipment table turns it into the mass of each bower anchor, the total length of chain cable and the chain diameter in grade 1, 2 or 3.
  3. Between two rows, the rules say use the lower row’s equipment.
  4. A high-holding-power anchor may be 25% lighter than an ordinary one; a higher chain grade gives a smaller diameter for the same ship.
  5. Example: an equipment number of 1,000 calls for 3,060 kg anchors, 495 m of chain, and 56, 50 or 44 mm chain in grade 1, 2 or 3.

Figures verified · Equipment table as published in a chain stockist’s reference sheets, following the class rules. The equipment number itself, and the table that applies, are set by the ship’s classification society.

Nobody chooses a ship’s anchor chain by feel. The classification society works out the ship’s equipment number, and a table gives the rest: how heavy the anchors must be, how much chain to carry and how thick it must be. If you are replacing a cable, the existing certificate already tells you the answer. If you are specifying new equipment — or checking that a cable offered to you is right for the ship — the equipment table is where to start.

/01What the number measures.

The anchors and cable have to hold the ship against wind and current. The pull grows with the ship’s size and with the area of hull, superstructure and deckhouses those forces act on, so the equipment number combines a displacement term with area terms. The exact formula, and the symbols in it, are in each society’s rules; your class society or naval architect will have calculated it for the ship, and it appears on the ship’s equipment documentation as a number and a letter.

/02The equipment table.

The table below is as published in a chain stockist’s reference sheets. For each range: the mass of each ordinary bower anchor, the mass if a high-holding-power (HHP) anchor is used, the total chain cable length, and the minimum chain diameter in grade 1, 2 and 3 (U1, U2, U3). A dash means that grade is not used at that size. The classification societies also give each row a letter — the same table in one society’s rules runs from A to Z and on with A+ and A*, in another’s from U1 to U61.

Equipment table, part 1 — equipment number 50 to 1,789
Equipment numberAnchor kgHHP anchor kgTotal chain mGrade 1 mmGrade 2 mmGrade 3 mm
50–691801352201412.5—
70–892401802201614—
90–109300225247.517.516—
110–129360270247.51917.5—
130–14942031527520.517.5—
150–1744803602752219—
175–204570430302.52420.5—
205–239660495302.5262220.5
240–279780585330282422
280–319900675357.5302624
320–3591,020765357.5322824
360–3991,140855385343026
400–4491,290970385363228
450–4991,4401,080412.5383430
500–5491,5901,195412.5403430
550–5991,7401,305440423632
600–6591,9201,440440443834
660–7192,1001,575440464036
720–7792,2801,710467.5484236
780–8392,4601,845467.5504438
840–9092,6401,980467.5524640
910–9792,8502,140495544842
980–10593,0602,295495565044
1060–11393,3002,475495585046
1140–12193,5402,655522.5605246
1220–12993,7802,835522.5625448
1300–13894,0503,040522.5645650
1390–14794,3203,240550665850
1480–15694,5903,445550686052
1570–16694,8903,670550706254
1670–17895,2503,940577.5736456
Equipment table, part 2 — equipment number 1,790 to 10,000
Equipment numberAnchor kgHHP anchor kgTotal chain mGrade 1 mmGrade 2 mmGrade 3 mm
1790–19295,6104,210577.5766658
1930–20796,0004,500577.5786860
2080–22296,4504,840605817062
2230–23796,9005,175605847364
2380–25297,3505,515605877666
2530–26997,8005,850632.5907868
2700–28698,3006,225632.5928170
2870–30398,7006,525632.5958473
3040–32099,3006,975660978476
3210–33999,9007,4256601008778
3400–359910,5007,8756601029078
3600–379911,1008,325687.51059281
3800–399911,7008,775687.51079584
4000–419912,3009,225687.51119787
4200–439912,9009,67571511410087
4400–459913,50010,12571511710290
4600–479914,10010,57571512010592
4800–499914,70011,025742.512210795
5000–519915,40011,550742.512411197
5200–549916,10012,075742.512711197
5500–579916,90012,675742.5130114100
5800–609917,80013,350742.5132117102
6100–649918,80014,100742.5137120107
6500–689920,00015,000770—124111
6900–739921,50016,125770—127114
7400–789923,00017,250770—132117
7900–839924,50018,375770—137122
8400–889926,00019,500770—142127
8900–939927,50020,625770—147132
9400–1000029,00021,750770—152132

/03Using it.

Take a ship with an equipment number of 1,000. It falls in the 980–1,059 row:

  • Anchors: 3,060 kg each, or 2,295 kg if HHP anchors are fitted — see marine anchors.
  • Chain length: 495 m in total — eighteen 27.5 m shots, split between the port and starboard cables.
  • Chain size: 56 mm in grade 1, 50 mm in grade 2 or 44 mm in grade 3. Grade 2 is the usual choice; grade 3 saves weight and locker space.

Then check the result against the anchor chain size chart for its test loads and the weight chart for what the windlass will lift. Every length in the table is a whole number of 27.5 m shots, and every anchor is proof tested to a load set by its mass — see anchor proof load testing.

Common questions

What is an equipment number used for?
To size a ship’s anchoring equipment under the class rules: anchor mass, total chain length and chain diameter.
What chain size does an equipment number of 2,000 need?
The 1,930–2,079 row gives 78 mm in grade 1, 68 mm in grade 2 or 60 mm in grade 3, with 577.5 m of chain and 6,000 kg anchors.
How much lighter can a high-holding-power anchor be?
In this table the HHP anchor mass is 75% of the ordinary anchor mass at every row.
Does a higher chain grade change the length?
No. The grade changes the diameter; the total length depends only on the equipment number.
Where do I find my ship’s equipment number?
In the ship’s class documentation, usually with its equipment letter. The anchor and chain certificates should match it.

Anchors and chain to the equipment table

What next

  1. 01
  2. 02

Know the equipment number?

Send it with the chain grade you want. We will quote the anchors, chain cable, shackles and forerunners as one package, with class certificates.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Anchor chain & mooring

All articles in this topic
Back to Blog