R1 1SC Compact Single Wire Braid Hose
Compact single-wire-braid hose with half the bend radius of EN 853 1SN — for tight routing in mobile equipment. 1/4" – 1-1/4" (DN6 – DN31).
Key features
- Applicable Standard: EN 857 1SC
- Construction Type: compact-1-wire
- Bore Size Range: 1/4" – 1-1/4" (DN6 – DN31)
- Max Working Pressure: 225 bar
- Min Burst Pressure: 900 bar
- Min Operating Temperature: -40 °C
- Max Operating Temperature: 100 °C
- Reinforcement: One layer of high-tensile steel wire braid
- Applicable Standard
- EN 857 1SC
- Construction Type
- compact-1-wire
- Bore Size Range
- 1/4" – 1-1/4" (DN6 – DN31)
- Max Working Pressure
- 225 bar
- Min Burst Pressure
- 900 bar
- Min Operating Temperature
- -40 °C
Product description
The R1 1SC Compact Single Wire Braid Hose Compact single-wire-braid hose with half the bend radius of EN 853 1SN — for tight routing in mobile equipment. Conforms to EN 857 1SC.
Construction
- Tube: Synthetic rubber (NBR), oil-resistant
- Reinforcement: One layer of high-tensile steel wire braid
- Cover: Synthetic rubber, abrasion- and weather-resistant, wrapped
Performance
Working pressures up to 225 bar at -04, falling to 105 bar at -12, with a minimum burst of 900 bar (safety factor 4:1). Continuous service from -40°C to 100°C, with the upper limit reduced for aggressive fluids — ask for a fluid compatibility chart if needed.
Applications
- Tight routing on mobile hydraulics where space is constrained
- Skid-steer loaders, mini-excavators, telehandlers
- Replacement of larger-OD R1 1SN where space saving is critical
Compliance
- EN 857 1SC
Also available in
The same EN 857 1SC grade is stocked in Eaton Winner and Parker Hannifin in addition to the Indus reference shown here. Tell us your brand preference on the RFQ and we will quote accordingly.
Companion grades
For higher pressures in compact construction see 2SC. For standard EN 853 dimensions see R1 1SN.
Identification
| Parameter | Value |
|---|---|
| Applicable Standard | EN 857 1SC |
| Construction Type | compact-1-wire |
Dimensions
| Parameter | Value |
|---|---|
| Bore Size Range | 1/4" – 1-1/4" (DN6 – DN31) |
| Min Bend Radius | 50–180 mm by bore (50 mm at -04, 180 mm at -12) |
| Outside Diameter Range | 12.2–26.5 mm (-04 to -12) |
Performance
| Parameter | Value |
|---|---|
| Max Working Pressure | 225 bar |
| Min Burst Pressure | 900 bar |
| Working Pressure Range | 225 bar at -04 down to 105 bar at -12 |
| Safety Factor | 4:1 |
| Min Operating Temperature | -40 °C |
| Max Operating Temperature | 100 °C |
Construction
| Parameter | Value |
|---|---|
| Reinforcement | One layer of high-tensile steel wire braid |
| Tube (Inner) Material | Synthetic rubber (NBR), oil-resistant |
| Cover Material | Synthetic rubber, abrasion- and weather-resistant |
| Cover Finish | wrapped |
Compliance
| Parameter | Value |
|---|---|
| Conductivity | non-conductive |
Commercial
| Parameter | Value |
|---|---|
| Sold By | per-metre |
Shipping & lead time
What standard does this hose comply with?▾
What is the maximum working pressure?▾
What temperature range is supported?▾
What bore sizes are available?▾
Is this hose conductive?▾
What end fittings are recommended?▾
How is this hose sold?▾
What is the typical lead time?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 126 destinations
From the blog
Written about this part
Failure analysis
Why hydraulic hoses fail: six modes, and what each one leaves behind
A failed hose usually tells you why it failed. Abrasion, kinking, heat, cold-set, wrong routing and fitting problems each leave a different signature — and each has a different fix.
4 min read
Assembly, crimping & certification
Getting a hydraulic hose made: what to bring and what we measure
Bring the old hose if you have it. If you do not, four measurements and two photographs will get the assembly built correctly first time.
3 min read
Maintenance & reliability
Hydraulic hose inspection: what to look for, and what it means
A walk-round that takes ten minutes finds most of what is about to fail. What to look at, what each finding actually indicates, and where the judgement calls are.
2 min read
Engineers viewing this also looked at
R1 1SN Single Wire Braid Hydraulic Hose
R12 Four-Spiral High-Pressure Hose
R13 Multi-Spiral Very-High-Pressure Hose
R14 PTFE Hydraulic Hose
R15 Six-Spiral Ultra-High-Pressure Hose
R17 Compact High-Pressure Hose
R2 2SN Double Wire Braid Hydraulic Hose
