Skip to content
Drilling rig equipment

Shear-pin or reset relief valve: protecting a mud pump with a PRV or an RRV

Oteco makes two relief valves for mud pumps and manifolds. The PRV opens when a calibrated shear pin breaks and must be re-pinned. The RRV snaps open at its set pressure, can be opened by hand and needs no pins. How each works, how the set pressure is chosen, and which to specify.

Written by
Ayush Bhatia, Director
Published
Reading
5 min · 4 sections
Share
Triplex mud pump in a rig pump house with a cylindrical relief valve on its discharge line piped back to the mud tank
Every mud pump discharge carries a relief valve: shear-pin valves are re-pinned after they open, reset valves snap shut again.

At a glance

Key takeaways

  1. The PRV is a shear-pin relief valve. A calibrated pin breaks at the set pressure and the valve opens fully. Oteco gives its accuracy as about ±10 %, and the pin must be replaced after every relief.
  2. The RRV (Type RR) is a manual reset valve with no pins. It snaps fully open at the set pressure, can be opened by hand with a release button, and has an accuracy of about ±5 %.
  3. Set pressure on the PRV is chosen by pin number and by the number of pins. On the RRV it is set on one adjusting nut and read on an indicator.
  4. Oteco states that PRV parts interchange with Cameron-style shear relief valve parts, and that the RRV bonnet assembly interchanges with Cameron Type A and B.
  5. Whichever you fit, the discharge line must be rated for the full inlet pressure and anchored against the reaction force.

A mud pump cannot be allowed to run against a closed line. The relief valve is the last protection between a blocked discharge and a burst manifold, and it has to open when it should, every time. Oteco makes two designs for the job. They protect the same equipment but behave differently after the valve has relieved, and that difference is what you are choosing between.

/01How the PRV (shear-pin) valve works.

In the 2-inch and 3-inch PRV, a calibrated shear pin holds the valve shut. When line pressure reaches the set point the pin breaks and the valve opens fully to relieve the pump. The relief pressure is set by the number and grade of the pins. A metal chart on every valve gives the pin for each set point, and a quick-release safety cover gives fast access to replace the pin afterwards. Oteco pins are precision ground and destructively tested in production, which gives the repeatable set point, about ±10 %. Stems and liner subs are hardened stainless steel.

The pins are colour-coded and sold in packs of ten: #3 brown up to #60 orange. As an example, the 2-inch 21050 relieves at 1,000 psi with a single #16 blue pin and at 2,500 psi with a #60 orange pin; with two pins the range doubles, from 2,000 to 5,000 psi. Oteco warns that nails or improvised pins cannot give an accurate relief pressure, and says to replace the pin after every relief, with the safety cover closed before the pump is restarted (Oteco Engineering Bulletin EB-003).

/02How the RRV (reset) valve works.

The Type RR valve does the same job without a pin. When pressure passes the set point, the valve snaps fully open; it can also be opened by hand with the release button, and the button position shows whether the valve is open or closed. The set pressure is read on an indicator (psi, bar or kPa scales) and adjusted by turning one nut on top. Vibration does not move the setting, and the fully enclosed bonnet keeps its grease. The piston is stainless steel and the subs are cadmium plated.

The RRV comes in 2-inch and 3-inch versions for 400 to 5,000 psi, and a heavy 3-inch for 3,000 to 8,000 psi and 4,000 to 10,000 psi. Oteco states that this high-pressure design was verified at an independent laboratory and on pumps from 700 to 3,000 hp.

/03Side by side.

Oteco PRV and RRV compared (from the Oteco brochures)
FeaturePRV (shear pin)RRV (Type RR reset)
Sizes2 and 3 in2 and 3 in
Set range, nominal125 to 10,000 psi across the models400 to 10,000 psi across the models
How it is setBy pin number and number of pinsOne adjusting nut, read on an indicator
AccuracyAbout ±10 %About ±5 %
After it relievesFit a new pin, close the coverReset it; no pins to replace
Manual openingNoYes, release button
Flow areaNot published1.8 in² (2 in), 4.2 in² (3 in, 5,000 psi), 4.9 in² (3 in, 8,000 psi)
TemperatureNameplate example: 250 °F maximum−20 °F to 250 °F
Published interchangeCameron-style shear relief valve partsBonnet assembly: Cameron Type A and B

Cameron is a trademark of its owner. Oteco also rebuilds or exchanges worn Oteco, Cameron Type A and Type B reset relief valve bonnet assemblies.

/04Which one to specify.

  • Choose the PRV where a low-cost, simple valve is wanted and the crew is used to re-pinning. Its pressure range covers 125 to 10,000 psi, including low-pressure models, and spare parts and kits are listed for every model.
  • Choose the RRV where you want to avoid a pin change after each trip, want tighter accuracy, or want to open the valve by hand. Its set pressure can be read and adjusted on site.
  • High-pressure pumps up to 10,000 psi: both families have models here. Compare the set ranges in the listings against your pump’s working pressure.
  • Approvals: Oteco states DNV type approval on selected PRV union models, and ABS design assessment and DNV approval on selected RRV models. Check the model number against the approval you need, because it applies to named models, not the whole range.

Hammer-union versions have a Figure 1502 female inlet and male outlet, made to mate with FMC Weco unions (Oteco Engineering Bulletin EB-004). Weco is a trademark of its owner. For the wider picture of relief valve types see oilfield pressure relief valves.

Common questions

Do I replace the shear pin after every relief?
Yes. Oteco says to replace the pin after every relief, with the safety cover closed before the pump is restarted (Engineering Bulletin EB-003).
What is in a PRV repair kit?
A minor repair kit holds a stem cushion, a piston and an O-ring. A major kit adds the stem. Kits are listed by model.
Can I use ordinary pins or nails in a PRV?
No. Oteco warns that improvised pins cannot give an accurate relief pressure. Use Oteco pins of the right number for the set point on the valve’s chart.
Can a reset relief valve be opened by hand?
Yes. The RRV has a release button, and the button position also shows whether the valve is open or closed.
Do you supply rebuilt RRVs?
Oteco offers rebuilt exchange valves, listed among the RRV spare parts, and rebuilds worn Oteco, Cameron Type A and Type B bonnet assemblies.

PRV and RRV valves, pins and kits

What next

  1. 01
  2. 02

Specifying a relief valve?

Send the pump pressure, set point, size and end connections, or the Oteco part number. We keep Oteco stock at our warehouse in Dubai, UAE, and ship worldwide.

Plant-down? Call +971 52 2477942 — 24/7

Keep reading

More on Drilling rig equipment

All articles in this topic
Triplex mud pump fluid end with a spherical pulsation dampener on the discharge, a technician removing a valve cover

Mud pump valves, seats and pulsation dampener diaphragms

5 min read

Back to Blog