R6 Single Fibre Braid Low-Pressure Hose

Single-fibre-braid low-pressure hose for fuel, oil, air, and mild hydraulic service. 1/4" – 1" (DN6 – DN25).
Key features
- Applicable Standard: SAE 100R6
- Construction Type: fiber-braid-thermoplastic
- Bore Size Range: 1/4" – 1" (DN6 – DN25)
- Max Working Pressure: 28 bar
- Min Burst Pressure: 112 bar
- Min Operating Temperature: -40 °C
- Max Operating Temperature: 100 °C
- Reinforcement: One textile braid
- Applicable Standard
- SAE 100R6
- Construction Type
- fiber-braid-thermoplastic
- Bore Size Range
- 1/4" – 1" (DN6 – DN25)
- Max Working Pressure
- 28 bar
- Min Burst Pressure
- 112 bar
- Min Operating Temperature
- -40 °C
Product description
The R6 Single Fibre Braid Low-Pressure Hose Single-fibre-braid low-pressure hose for fuel, oil, air, and mild hydraulic service. Conforms to SAE 100R6.
Construction
- Tube: Synthetic rubber (NBR), oil-resistant
- Reinforcement: One textile braid
- Cover: Synthetic rubber, weather-resistant, wrapped
Performance
Working pressures up to 28 bar at -04, falling to 20 bar at -16, with a minimum burst of 112 bar (safety factor 4:1). Continuous service from -40°C to 100°C, with the upper limit reduced for aggressive fluids — ask for a fluid compatibility chart if needed.
Applications
- Fuel and lubricating oil transfer
- Compressed-air lines on light-duty equipment
- Anti-static drain lines on agricultural machinery
Compliance
- SAE 100R6
Also available in
The same SAE 100R6 grade is stocked in Eaton Aeroquip and Parker Hannifin in addition to the Eaton Winner reference shown here. Tell us your brand preference on the RFQ and we will quote accordingly.
Companion grades
For higher hydraulic pressures see R3 (two-fibre) or step up to R1 1SN (wire braid).
Identification
| Parameter | Value |
|---|---|
| Applicable Standard | SAE 100R6 |
| Construction Type | fiber-braid-thermoplastic |
Dimensions
| Parameter | Value |
|---|---|
| Bore Size Range | 1/4" – 1" (DN6 – DN25) |
| Min Bend Radius | 65–170 mm by bore (65 mm at -04, 170 mm at -16) |
| Outside Diameter Range | 12.3–33.2 mm (-04 to -16) |
Performance
| Parameter | Value |
|---|---|
| Max Working Pressure | 28 bar |
| Min Burst Pressure | 112 bar |
| Safety Factor | 4:1 |
| Working Pressure Range | 28 bar at -04 down to 20 bar at -16 |
| Min Operating Temperature | -40 °C |
| Max Operating Temperature | 100 °C |
Construction
| Parameter | Value |
|---|---|
| Reinforcement | One textile braid |
| Tube (Inner) Material | Synthetic rubber (NBR), oil-resistant |
| Cover Material | Synthetic rubber, weather-resistant |
| Cover Finish | wrapped |
Compliance
| Parameter | Value |
|---|---|
| Conductivity | non-conductive |
Commercial
| Parameter | Value |
|---|---|
| Sold By | per-metre |
Shipping & lead time
What is R6 Single Fibre Braid Low-Pressure Hose used for?▾
Which sizes does R6 Single Fibre Braid Low-Pressure Hose come in?▾
How do I order R6 Single Fibre Braid Low-Pressure Hose by size and length?▾
What is the working pressure of R6 Single Fibre Braid Low-Pressure Hose?▾
What temperatures and fluids can R6 Single Fibre Braid Low-Pressure Hose handle?▾
What standard does R6 Single Fibre Braid Low-Pressure Hose conform to?▾
What end fittings go on R6 Single Fibre Braid Low-Pressure Hose?▾
What is the minimum bend radius of R6 Single Fibre Braid Low-Pressure Hose and how do I route it?▾
What applications is R6 Single Fibre Braid Low-Pressure Hose recommended for?▾
R6 Single Fibre Braid Low-Pressure Hose or R1 1SN Single Wire Braid Hydraulic Hose: which should I choose?▾
Where does R6 Single Fibre Braid Low-Pressure Hose come from and how is it shipped?▾
Do you stock R6 Single Fibre Braid Low-Pressure Hose in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog
Written about this range
Machine down
Detaching a hose on a modern machine: guards, clips and the ones that fight back
On a machine built in the last fifteen years, getting to the hose takes longer than changing it. Most of that time is spent undoing things nobody photographed.
5 min read
Procurement & export
Bulk hose by the metre, or finished assemblies?
Buying hose on a reel and crimping your own looks cheaper and sometimes is. The decision turns on whether you can state a crimp diameter and prove you hit it.
3 min read
Failure analysis
Cover blistering and pinholes: usually permeation, not a defect
A bubble under the cover looks like a manufacturing fault and normally is not. It is gas that got through the tube and could not get out through the cover — which tells you something specific about the fluid and the duty.
4 min read







