Drag Hose Fitting

Drag Hose Fitting — hard-anodised aluminium umbilical slurry fitting for agricultural drag hose, held by a hose clamp. Sizes 4", 5", 6", 8" and 10". Fitting: Aluminum with Hard Anodized. Supplied by Sunpool (Taiwan); RFQ-only via Indus Hydraulics authorised distribution.
Key features
- Coupling Family: KC Nipple / Industrial Hose Fitting
- Coupling Type / Variant: KC Nipple & Hose Fitting — Drag Hose Fitting
- Size Range: 4", 5", 6", 8", & 10"
- Coupling Family
- KC Nipple / Industrial Hose Fitting
- Coupling Type / Variant
- KC Nipple & Hose Fitting — Drag Hose Fitting
- Size Range
- 4", 5", 6", 8", & 10"
Product description
The Drag Hose Fitting is a KC Nipple / Industrial Hose Fitting from the Sunpool (Taiwan) industrial coupling range. Indus Hydraulics is an authorised distributor in the UAE.
Configuration
- Coupling family: KC Nipple / Industrial Hose Fitting
- Coupling type: KC Nipple & Hose Fitting — Drag Hose Fitting
Specifications
- Size range: 4", 5", 6", 8" and 10"
- Material: Fitting: Aluminum with Hard Anodized
- Working pressure: Not published by Sunpool. Give us your working pressure and medium and we will check it with the manufacturer.
Manufacturer notes
- Hy flow umbilical slurry coupling for drag hose.
- Designed for agriculture drag hose.
- Can be easily removed or joined to the hose by hose clamp without specialist tools.
About the family
KC (king combination) nipples are hose tails: a serrated shank that goes inside the hose, and a threaded, grooved or flanged end that connects to pipe or another fitting. The hose is held on the tail by a clamp, ferrule or sleeve, and that is what sets how much pressure the joint holds. Sunpool makes standard KC nipples from 1/2" to 12" in plated carbon steel, SS304 and SS316; heavy-duty versions with a thicker wall and a longer tail for crimping with a ferrule, with or without a welded #150 flange; grooved nipples for rigid grooved couplings; and hose menders. The same shelf carries large-bore fittings for agricultural drag hose and frac-water lines, a Figure 206 hammer-union hose coupling and suction hose couplings.
Selection and service notes
The clamp, ferrule or sleeve over the hose usually limits the assembly, not the nipple: rate the joint at its weakest part. Sunpool rates its heavy-duty KC nipples and flanges at 300 psi and publishes no rating for the rest. Specify the end thread and give the hose outside diameter for the ferrule or sleeve.
How to order
Specify the size, the body material where more than one is listed, and any thread, tail or gasket variant on the RFQ. Indus engineering will confirm the manufacturer part number against your application.
Further reading: KC nipples, shank couplings and hose menders.
Sunpool sizes
Sunpool lists this part in 4", 5", 6", 8" and 10".
Sizes from Sunpool’s catalogue page for this part, checked 7 October 2026.
Identification
| Parameter | Value |
|---|---|
| Coupling Family | KC Nipple / Industrial Hose Fitting |
| Coupling Type / Variant | KC Nipple & Hose Fitting — Drag Hose Fitting |
Dimensions
| Parameter | Value |
|---|---|
| Size Range | 4", 5", 6", 8", & 10" |
Construction
| Parameter | Value |
|---|---|
| Materials Available | Fitting: Aluminum with Hard Anodized |
Notes
| Parameter | Value |
|---|---|
| Notes | Hy flow umbilical slurry coupling for drag hose. Designed for agriculture drag hose. Can be easily removed or joined to the hose by hose clamp without specialist tools. |
Shipping & lead time
Sizes & part numbers
5 sizes- Indus part no.IH-KC-DRAG-HOSE-FITTING-400
- Nominal size
- 4"
- Indus part no.IH-KC-DRAG-HOSE-FITTING-500
- Nominal size
- 5"
- Indus part no.IH-KC-DRAG-HOSE-FITTING-600
- Nominal size
- 6"
- Indus part no.IH-KC-DRAG-HOSE-FITTING-800
- Nominal size
- 8"
- Indus part no.IH-KC-DRAG-HOSE-FITTING-1000
- Nominal size
- 10"
What is the drag hose fitting used for?▾
How do I read the drag hose fitting part numbers?▾
What sizes does the drag hose fitting come in?▾
What working pressure does the drag hose fitting have?▾
What is the drag hose fitting made of?▾
Does Indus supply test certificates with the drag hose fitting?▾
What does the drag hose fitting connect to?▾
How do I fit the drag hose fitting to a hose?▾
Where is the drag hose fitting typically used?▾
How does the drag hose fitting differ from the umbilical slurry coupling set?▾
Where is the drag hose fitting made, and is it stocked?▾
Is the drag hose fitting in stock in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
The same part, in the designations used across European and Gulf trade catalogues.
- de
- KC-Kupplung
- fr
- raccord KC
- es
- acoplamiento KC
- it
- raccordo KC
From the blog
Written about this range
Industrial hose
KC nipples and shank couplings: the plain hose end, and how to make it hold
A serrated tail, a thread or a flange, and a clamp: KC nipples, shank couplings, pin-lug couplings and menders are the simplest hose ends there are. Which one to use, and the clamp that decides the rating.
5 min read
Industrial hose
Flanged hose connections: ASME B16.5 flange types, classes and faces on industrial hose
Where a hose meets fixed pipework, it usually meets a flange. The flange types we stock, what Class 150 and 300 mean, RF against FF against RTJ, and the stub-end trick that lets the bolt holes line up.
5 min read
Industrial hose
How to repair lay flat hose: cutting out, re-coupling and menders
A cut, a burst fold or a crushed coupling does not have to mean a new hose. Most lay flat damage is repaired by cutting out the bad section and re-coupling, or — on low-pressure lines — joining the ends with a mender. When to repair and when to scrap, how to make each repair properly, and the extra rules that apply to fire hose.
4 min read








