Connecting Link for Pennant Lines

Connecting Link for Pennant Lines. Indus part number.
Key features
- Product type: Connecting Link for Pennant Lines
- Size range: 400 t MBL
Product description
Connecting link for joining pennant wires.
Configuration
Supplied as one configuration: 400 t MBL. Its Indus part number is in the table below.
Proof and breaking loads are as published for each size. They are test values, not working loads.
Dimensions are typical and can vary slightly between production runs; the drawing sent with the quotation is final.
Specifying
State the chain or wire size the connector joins, the load you need and the certificate required.
Ordering
Quote the Indus part number from the size table, or send the size and rating you need.
Identification
| Parameter | Value |
|---|---|
| Product type | Connecting Link for Pennant Lines |
| Sizes | 1 |
Dimensions
| Parameter | Value |
|---|---|
| Size range | 400 t MBL |
Shipping & lead time
Sizes & part numbers
1 size- Indus part no.IH-MR-CN-CLK-400T
- Size
- 400 t MBL
- Proof load (t)
- 200
- Min breaking load (t)
- 400
- A (mm)
- 560
- B (mm)
- 363
- C (mm)
- 108
- D (mm)
- 76.2
- E (mm)
- 103
- F (mm)
- 58
- R (mm)
- 76.2
Size — Nominal size as the manufacturer states it. Proof load — Proof or test load the manufacturer applies to the part. A test figure — never a working limit. Min breaking load — Minimum breaking load. A test figure — never lift to it. A — Dimension A on the manufacturer dimension drawing. B — Dimension B on the manufacturer dimension drawing. C — Dimension C on the manufacturer dimension drawing. D — Dimension D on the manufacturer dimension drawing. E — Dimension E on the manufacturer dimension drawing. F — Dimension F on the manufacturer dimension drawing. R — Dimension R on the manufacturer dimension drawing. Ask us for the dimension drawing if you need it stamped.
WLL is the most the part may carry in service. Proof and breaking loads are test figures — never lift to them. Each load is shown in the unit the manufacturer rates the part in, and a size ships with the manufacturer’s test certificate.
This range is published with a breaking load only, not a working load limit. Tell us the duty before using it to lift, and we will confirm a rating or recommend a rated part.
What is the Connecting Link for Pennant Lines used for?▾
Which sizes of Connecting Link for Pennant Lines are available?▾
How do I size the Connecting Link for Pennant Lines for a mooring?▾
What load does the Connecting Link for Pennant Lines carry?▾
How do I order the Connecting Link for Pennant Lines?▾
How does the Connecting Link for Pennant Lines compare with the Swivel Connecting Link?▾
What do the letters in the Connecting Link for Pennant Lines size table mean?▾
Which certificate can I get for the Connecting Link for Pennant Lines?▾
What is the Connecting Link for Pennant Lines connected with in a mooring?▾
How should the Connecting Link for Pennant Lines be inspected and installed?▾
What are the typical uses of the Connecting Link for Pennant Lines?▾
Can I buy the Connecting Link for Pennant Lines ex-stock from Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog
Written about this range
Anchor chain & mooring
Offshore mooring components: H-links, pear links, triangle plates, LTM shackles and swivels
A mooring line is chain, wire or rope joined by connectors, each one rated to the line’s grade. What the H-link, pear link and pear shackle, triangle plate, LTM joining and end shackles, installation links, swivels and chasers do, and where each sits in a mooring leg.
5 min read
Anchor chain & mooring
Offshore mooring chain grades ORQ, R3, R3S, R4, R4S and R5: strength, toughness and loads
The six offshore mooring chain grades compared: tensile and yield strength, elongation, reduction of area and Charpy impact energy for each, the IACS test-load constants, what 76 mm chain carries in every grade, and how the R grades differ from ship anchor chain grade U3.
4 min read
Anchor chain & mooring
Chain locker volume: how much space anchor chain needs, with a formula and table
A chain locker must hold the whole cable with room for it to pile and run free. The formula classification practice uses, the volume per 100 m and per shot for every chain size from 12.5 to 162 mm, a worked example, and the rules for the locker itself.
4 min read








