Dinamic Oil RW Planetary Winch Drives — 7,380 to 32,530 Nm, DNV Type Approved

Dinamic Oil RW rotating-case planetary winch drives, 2 or 3 stages, 7,380 Nm to 32.53 kNm FEM torque, DNV type approved, built in Italy. From Indus Hydraulics, authorised Dinamic Oil distributor, UAE.
Key features
- Product type: Planetary winch drive (rotating case)
- Series: Dinamic Oil RW
- Execution: In-drum, single support bearing
- Reduction stages: 2 or 3
- Output torque: T2 FEM 7,380 to 32,530 Nm (M5-L2-T5, 25 rpm)
- Reduction ratio: 13.40 to 226.66:1
- Motor / input: Hydraulic motor, SAE B / C / D flange; electric or input shaft on request
- Brake: Negative multi-disc, FW (to 1,600 Nm) or FY (to 3,600 Nm), freewheel option
- Type approval: DNV TAS00001JK (all RW sizes, to 2029-01-01)
- Product type
- Planetary winch drive (rotating case)
- Series
- Dinamic Oil RW
- Execution
- In-drum, single support bearing
- Reduction stages
- 2 or 3
- Type approval
- DNV TAS00001JK (all RW sizes, to 2029-01-01)
Product description
RW winch drives cover the torques below the WD range — from about 7 kNm to 33 kNm FEM — in two-stage builds, whose lower ratios suit electric motors, and three-stage builds for hydraulic motors. Like the WD, the RW is a rotating-case gearbox that mounts inside the drum.
Indus Hydraulics is an authorised Dinamic Oil distributor and supplies direct from Dinamic Oil's factory in Bomporto, Italy.
Ratings
The table gives each size's highest FEM torque (T2 FEM, class M5-L2-T5 at 25 rpm, to FEM 1.001) and highest maximum dynamic torque across its ratios, with the ratio range. Torque varies with ratio: the per-ratio values, the bearing ratings of the rotating flange and the flange dimensions are in Dinamic Oil's winch-drive catalogue. For another FEM class, multiply the FEM torque by the catalogue's coefficient c — for example, class L3-T4 at 12 rpm takes 0.90.
Approvals
Every RW size in the catalogue — RW 512 to RW 2522 and RW 513 to RW 1023 — is covered by DNV type approval TAS00001JK for shipboard and offshore lifting appliances, life-saving appliance (davit) winches and drilling facilities, valid to January 2029.
Selection
Pick the size whose ratio is close to the one the winch needs and whose FEM torque, multiplied by the class coefficient, is above the application torque. Then check the rotating-flange bearing: its static rating must cover the drum load, and its life (Lh10) must meet the FEM class. Peak dynamic and static torques must stay below the table maxima, and for continuous input speeds above 1,500 rpm Dinamic Oil recommends its high-speed brake versions.
Custom builds
For heavier winches Dinamic Oil builds made-to-measure rotating-case drives up to 3,000,000 Nm, in-line or right-angle, with one or several motor inputs. Tell us the torque, ratio and motor arrangement and we will put the request to the factory.
Lubrication and service
Oil bath, ISO VG 220 to 320 EP gear oil. First change after 150 operating hours, then at the catalogue interval or at least every two years. Standard ambient range −20 °C to +40 °C.
Options and accessories
- Brakes: FW negative multi-disc brakes from 230 to 1,600 Nm and FY brakes from 1,840 to 3,600 Nm static torque, SAE B, C or D motor flanges; low-opening-pressure versions for brakes controlled from the charge pump; special-lubrication versions for continuous input above 1,500 rpm; optional freewheel (sprag clutch) against load drop while hoisting. See brakes for winch drives.
- Configurations: without brake, set up for an electric motor, or with a high-speed input shaft; other motor inputs on demand.
- Drum (WDD): smooth, standard grooved or Lebus-type grooved, length and diameter to order; rope anchored with clamps or a wedge lock; clockwise or counterclockwise, overshot or underpull.
- Winch accessories: every accessory of the hydraulic winch range — rope tensioner, limit switches, load limiters and the ELD load detection system. See hydraulic winch accessories.
- Certification: DNV type approval on RW and three-stage WD; product certificates or design approval from other societies on request.
Identification
| Parameter | Value |
|---|---|
| Product type | Planetary winch drive (rotating case) |
| Series | Dinamic Oil RW |
| Execution | In-drum, single support bearing |
Performance
| Parameter | Value |
|---|---|
| Reduction stages | 2 or 3 |
| Output torque | T2 FEM 7,380 to 32,530 Nm (M5-L2-T5, 25 rpm) |
| Reduction ratio | 13.40 to 226.66:1 |
Construction
| Parameter | Value |
|---|---|
| Motor / input | Hydraulic motor, SAE B / C / D flange; electric or input shaft on request |
| Brake | Negative multi-disc, FW (to 1,600 Nm) or FY (to 3,600 Nm), freewheel option |
| Lubrication | Oil bath, ISO VG 220–320 EP gear oil; first change after 150 h, then by the catalogue interval or at least every 2 years |
Compliance
| Parameter | Value |
|---|---|
| Rating basis | FEM 1.001; ISO 6336 / ISO 281 |
| Type approval | DNV TAS00001JK (all RW sizes, to 2029-01-01) |
Supply
| Parameter | Value |
|---|---|
| Made in | Italy (Dinamic Oil S.p.A., Bomporto) |
| Supply | Authorised distributor, direct from the factory |
Shipping & lead time
Sizes & part numbers
10 sizes- Indus part no.IH-DO-RW-512
- Description
- RW 512
- Stages
- 2
- Output torque (Nm)
- 7,380
- Peak torque (Nm)
- 12,500
- Weight (kg)
- 75
- Ratio
- 13.79 – 43.64
- Indus part no.IH-DO-RW-513
- Description
- RW 513
- Stages
- 3
- Output torque (Nm)
- 7,800
- Peak torque (Nm)
- 12,900
- Weight (kg)
- 85
- Ratio
- 42.60 – 189.30
- Indus part no.IH-DO-RW-612
- Description
- RW 612
- Stages
- 2
- Output torque (Nm)
- 9,800
- Peak torque (Nm)
- 16,200
- Weight (kg)
- 90
- Ratio
- 13.40 – 33.13
- Indus part no.IH-DO-RW-613
- Description
- RW 613
- Stages
- 3
- Output torque (Nm)
- 10,300
- Peak torque (Nm)
- 16,200
- Weight (kg)
- 100
- Ratio
- 49.11 – 201.89
- Indus part no.IH-DO-RW-812
- Description
- RW 812
- Stages
- 2
- Output torque (Nm)
- 11,750
- Peak torque (Nm)
- 18,000
- Weight (kg)
- 130
- Ratio
- 14.14 – 42.74
- Indus part no.IH-DO-RW-813
- Description
- RW 813
- Stages
- 3
- Output torque (Nm)
- 12,400
- Peak torque (Nm)
- 20,800
- Weight (kg)
- 140
- Ratio
- 43.60 – 207.31
- Indus part no.IH-DO-RW-1022
- Description
- RW 1022
- Stages
- 2
- Output torque (Nm)
- 16,600
- Peak torque (Nm)
- 26,880
- Weight (kg)
- 145
- Ratio
- 14.14 – 42.74
- Indus part no.IH-DO-RW-1023
- Description
- RW 1023
- Stages
- 3
- Output torque (Nm)
- 18,150
- Peak torque (Nm)
- 30,000
- Weight (kg)
- 155
- Ratio
- 43.60 – 226.66
Show all 10 sizesShow fewer sizes
- Indus part no.IH-DO-RW-1532
- Description
- RW 1532
- Stages
- 2
- Output torque (Nm)
- 22,650
- Peak torque (Nm)
- 37,200
- Weight (kg)
- 195
- Ratio
- 17.90 – 45.73
- Indus part no.IH-DO-RW-2522
- Description
- RW 2522
- Stages
- 2
- Output torque (Nm)
- 32,530
- Peak torque (Nm)
- 53,000
- Weight (kg)
- 275
- Ratio
- 17.51 – 41.81
Description — What this part number is, as the manufacturer lists it. Stages — Number of planetary reduction stages, as published. Output torque — Rated output torque, as the manufacturer publishes it. A circuit is limited by its lowest-rated component. The page states which rating it is. Peak torque — Maximum (peak) output torque, as the manufacturer publishes it. A circuit is limited by its lowest-rated component. Weight — Weight as the manufacturer publishes it. Ratio — Reduction ratio, or the range of ratios the model is built in, as published.
What is the Dinamic Oil RW Planetary Winch Drives used for?▾
How do I read a Dinamic Oil model number such as RW 513?▾
Which sizes of Dinamic Oil RW Planetary Winch Drives are available?▾
How do I select an RW Planetary Winch Drives winch drive size?▾
What torque rating do the Dinamic Oil RW Planetary Winch Drives carry and on what basis?▾
What oil and brakes do the Dinamic Oil RW Planetary Winch Drives use?▾
Are the Dinamic Oil RW Planetary Winch Drives DNV type approved?▾
What does the drum need to go with the Dinamic Oil RW Planetary Winch Drives?▾
How do I run the Dinamic Oil RW Planetary Winch Drives in Gulf summer heat?▾
How does the Dinamic Oil RW differ from the WD winch drive?▾
Are the Dinamic Oil RW Planetary Winch Drives genuine Dinamic Oil units and can you export them?▾
Do you keep the Dinamic Oil RW Planetary Winch Drives in stock in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog
Written about this part
Lifting & rigging
Winch drive, motor drum or complete winch: which to buy for a crane or offshore winch
Crane and winch builders can buy the drive, the drive already built into its drum, or the whole winch. What each one leaves you to design, how a rotating-case winch drive is rated under FEM, and where class approval comes in.
3 min read
Specification & standards
DNV type approval for crane and winch gearboxes: what it covers and what it does not
A DNV type approval or an ABS product design assessment on a gearbox saves weeks on a classed crane or winch — if you know what it covers. What type approval, PDA and works recognition mean, what they leave to the project, and which Dinamic Oil drives carry them.
3 min read


