Dinamic Oil Hydraulic Winch Accessories — Rope Tensioners, Limit Switches, Load Limiters and ELD

Dinamic Oil hydraulic winch accessories: rope tensioner, electric and hydraulic lowering and rotary limit switches, strain-gauge and load-cell pull limiters, and the ELD electronic load detection system. From Indus Hydraulics, authorised Dinamic Oil distributor, UAE.
Key features
- Product type: Hydraulic winch accessory
- Series: Dinamic Oil B, C1, C2, D, E, ELD, F1, F2
- Execution: Factory-fitted with the winch
- Motor / input: Electric versions on 12–24 V DC control circuits; hydraulic versions in the winch circuit
- Product type
- Hydraulic winch accessory
- Series
- Dinamic Oil B, C1, C2, D, E, ELD, F1, F2
Product description
Dinamic Oil builds a set of accessories into its hydraulic winches and winch drums at the factory, ordered with the winch by its accessory code. They add rope control, end-of-travel protection and load monitoring to the NP, NPA, A, P, CW, S, SE and SRD series and to WDD motor drums.
Indus Hydraulics is an authorised Dinamic Oil distributor and supplies direct from Dinamic Oil's factory in Bomporto, Italy.
Rope control and limit switches
- B — rope tensioner: a pressure roller that keeps the rope tight on the drum so it spools evenly without load.
- C1 / C2 — tensioner with lowering limit switch: stops lowering before the last safety wraps leave the drum, by an electric micro switch (C1) or a hydraulic end-stroke valve (C2).
- F1 / F2 — rotary limit switch: a gear-cam switch for upper and lower travel limits, electric (F1) or hydraulic (F2), on request.
Load limiting and monitoring
- D — strain-gauge pull limiter: a strain-gauge bridge on the winch structure measures its deformation under rope pull; above the set load a solenoid valve stops hoisting while lowering stays possible. Because it measures the structure, not the drum torque, it reads the same on every rope layer.
- E — load cells: two load cells under the winch on its own base plate; the summed signal trips an alarm or stop, or displays the lifted load.
- ELD — electronic load detection: a strain-gauged anti-rotation flange inside the drum measures torque, and a phonic wheel with two proximity sensors counts drum turns and direction, so the system knows the working layer, rope paid out and the actual line pull in real time and shows it on the crane's remote control. It works with analogue and digital signals and a PLC or PC.
Not every accessory fits every series: the table shows where the catalogue shows each one. The pull limiters are available on all series except SRD.
Identification
| Parameter | Value |
|---|---|
| Product type | Hydraulic winch accessory |
| Series | Dinamic Oil B, C1, C2, D, E, ELD, F1, F2 |
| Execution | Factory-fitted with the winch |
Construction
| Parameter | Value |
|---|---|
| Output / mounting | NP, NPA, A, P, CW, S, SE, SRD winches; WDD drums |
| Motor / input | Electric versions on 12–24 V DC control circuits; hydraulic versions in the winch circuit |
Compliance
| Parameter | Value |
|---|---|
| Rating basis | Fitted and load-tested with the winch (UNI ISO 4301/1) |
Supply
| Parameter | Value |
|---|---|
| Made in | Italy (Dinamic Oil S.p.A., Bomporto) |
| Supply | Authorised distributor, direct from the factory |
Shipping & lead time
Sizes & part numbers
8 sizes- Indus part no.IH-DO-WACC-B
- Description
- B — Cable tensioner (rope press roller)
- Mount
- Series NP-NPA-A, P, CW, S-SE, SRD
- Indus part no.IH-DO-WACC-C1
- Description
- C1 — Cable tensioner + electric lower limit switch (lowering rope-end microswitch)
- Mount
- Series NP-NPA-A, P, CW, S-SE, SRD
- Indus part no.IH-DO-WACC-C2
- Description
- C2 — Cable tensioner + hydraulic lower limit switch (hydraulic lowering end stroke)
- Mount
- Series NP-NPA-A, P, CW, S-SE, SRD
- Indus part no.IH-DO-WACC-D
- Description
- D — Cable tensioner + lower limit switch + load limiting device (strain-gauge pull limiter)
- Mount
- —
- Indus part no.IH-DO-WACC-E
- Description
- E — Load cells (load-cell pull limiting system on winch base plate)
- Mount
- —
- Indus part no.IH-DO-WACC-ELD
- Description
- ELD — Electronic load detection system
- Mount
- —
- Indus part no.IH-DO-WACC-F1
- Description
- F1 — Electric rotary (gear cam) limit switch, up/down — on request
- Mount
- —
- Indus part no.IH-DO-WACC-F2
- Description
- F2 — Hydraulic rotary (gear cam) limit switch, up/down — on request
- Mount
- —
Description — What this part number is, as the manufacturer lists it. Mount — Mounting flange or pattern, as published. Ask us for the dimension drawing if you need it stamped.
What are Dinamic Oil hydraulic winch accessories?▾
What do the accessory codes B, C1, C2, D, E, ELD, F1 and F2 mean?▾
What does the B rope tensioner do?▾
What is the difference between the D pull limiter and the ELD system?▾
How does the D strain-gauge pull limiter work?▾
How does the ELD electronic load detection system work?▾
What standard are Dinamic Oil winch accessories fitted and tested to?▾
Do I need a lowering limit switch on a hydraulic winch?▾
Can accessories be added to a winch I already have?▾
What do the E load cells do compared with the D limiter?▾
Are Dinamic Oil winch accessories from Indus Hydraulics genuine?▾
Do you supply Dinamic Oil winch accessories from Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog
Written about this part
Safety & HSE
Crane winch load monitoring: limit switches, pull limiters, load cells and ELD
A crane winch can stop itself at the end of the rope, refuse to lift an overload, or tell the operator exactly what is on the hook. What each kind of winch load protection does, how it measures, and which one a crane needs.
4 min read
Lifting & rigging
Choosing a recovery winch for tow trucks: pull, cable, freewheel and fairlead
A recovery winch is sized on the pull it needs on the layer it works from, then fitted out for the job: freewheel to walk the cable out, a fairlead for angled pulls, and the right cable. How to choose one, with Dinamic Oil’s T series as the worked example.
3 min read



