Telescopic Spreader Beams — 4 t to 16 t, EN 13155

Telescopic spreader beams rated 4, 8, 12 and 16 t that slide to length and pin, for jobs where the span changes from lift to lift. Ten standard span ranges from 1.5 m to 6 m; other lengths and capacities to order.
Key features
- Product type: Telescopic spreader beam
- Pattern / standard: EN 13155
- Size range: Span 1.5–6 m standard; 1–10 m to order
- Working load limit: 4–16 t standard; 1–34 t to order
- Product type
- Telescopic spreader beam
- Material
- Steel, telescopic sections with pinned adjustment
Product description
A spreader beam with an inner section that slides inside the outer one and pins at drilled adjustment holes. Changing the span takes a pin, not a spanner, so it is the quickest beam to reset when one rig handles loads of different lengths. It is slightly heavier than a modular beam of the same capacity.
Standard sizes
| WLL | Span | Self weight | Adjustment step | Top shackles | Bottom shackles |
|---|---|---|---|---|---|
| 4 t | 1.5–2.5 m | 30 kg | 125 mm | 6.5 t | 4.75 t |
| 4 t | 2.5–4 m | 45 kg | 250 mm | 6.5 t | 4.75 t |
| 8 t | 1.5–2.5 m | 35 kg | 125 mm | 6.5 t | 4.75 t |
| 8 t | 2.5–4 m | 50 kg | 250 mm | 6.5 t | 4.75 t |
| 12 t | 1.5–2.5 m | 50 kg | 125 mm | 12 t | 8.5 t |
| 12 t | 2.5–4 m | 80 kg | 250 mm | 12 t | 8.5 t |
| 12 t | 4–6 m | 120 kg | 250 mm | 12 t | 8.5 t |
| 16 t | 1.5–2.5 m | 55 kg | 125 mm | 12 t | 8.5 t |
| 16 t | 2.5–4 m | 85 kg | 250 mm | 12 t | 8.5 t |
| 16 t | 4–6 m | 125 kg | 250 mm | 12 t | 8.5 t |
The WLL applies across the whole span range of each beam. The top shackles connect the beam to the top slings, and the bottom shackles take the load.
Built to order
Beyond the standard sizes, telescopic beams are built from 1 m to 10 m long and from 1 t to 34 t, with adjustment holes drilled where the job needs them, anywhere from 50 mm to 1000 mm apart.
Rules for use
- Load the beam only at its two end points through the bottom shackles.
- Keep the top sling angle at 45° to the vertical or less.
- Make sure the adjustment pin is fully home and secured before every lift.
Ordering
Quote the part number from the table, or send the load weight and the range of spans you need to cover, and we will propose the beam and its rigging.
Identification
| Parameter | Value |
|---|---|
| Product type | Telescopic spreader beam |
| Pattern / standard | EN 13155 |
| Sizes | 10 |
Performance
| Parameter | Value |
|---|---|
| Working load limit | 4–16 t standard; 1–34 t to order |
| Sling angle | 45° to vertical, maximum |
Dimensions
| Parameter | Value |
|---|---|
| Size range | Span 1.5–6 m standard; 1–10 m to order |
| Adjustment step | 125 mm or 250 mm standard; 50–1000 mm to order |
Construction
| Parameter | Value |
|---|---|
| Material | Steel, telescopic sections with pinned adjustment |
Compliance
| Parameter | Value |
|---|---|
| Certification | Declaration of conformity; user instructions |
Shipping & lead time
Sizes & part numbers
10 sizes- Indus part no.IH-LR-BH-TSB-4-1525
- Span
- 1.5–2.5 m
- WLL (t)
- 4
- Weight (kg)
- 30
- Indus part no.IH-LR-BH-TSB-4-2540
- Span
- 2.5–4 m
- WLL (t)
- 4
- Weight (kg)
- 45
- Indus part no.IH-LR-BH-TSB-8-1525
- Span
- 1.5–2.5 m
- WLL (t)
- 8
- Weight (kg)
- 35
- Indus part no.IH-LR-BH-TSB-8-2540
- Span
- 2.5–4 m
- WLL (t)
- 8
- Weight (kg)
- 50
- Indus part no.IH-LR-BH-TSB-12-1525
- Span
- 1.5–2.5 m
- WLL (t)
- 12
- Weight (kg)
- 50
- Indus part no.IH-LR-BH-TSB-12-2540
- Span
- 2.5–4 m
- WLL (t)
- 12
- Weight (kg)
- 80
- Indus part no.IH-LR-BH-TSB-12-4060
- Span
- 4–6 m
- WLL (t)
- 12
- Weight (kg)
- 120
- Indus part no.IH-LR-BH-TSB-16-1525
- Span
- 1.5–2.5 m
- WLL (t)
- 16
- Weight (kg)
- 55
Show all 10 sizesShow fewer sizes
- Indus part no.IH-LR-BH-TSB-16-2540
- Span
- 2.5–4 m
- WLL (t)
- 16
- Weight (kg)
- 85
- Indus part no.IH-LR-BH-TSB-16-4060
- Span
- 4–6 m
- WLL (t)
- 16
- Weight (kg)
- 125
Span — Distance between the lifting points the load hangs from, as the load chart prints it. WLL — Working load limit — the most the part may carry in service, as the manufacturer rates it. Weight — Weight as the manufacturer publishes it. Ask us for the dimension drawing if you need it stamped.
WLL is the most the part may carry in service. Proof and breaking loads are test figures — never lift to them. Each load is shown in the unit the manufacturer rates the part in, and a size ships with the manufacturer’s test certificate.
What is a telescopic spreader beam used for?▾
How are the Telescopic Spreader Beams — 4 t to 16 t part numbers such as IH-LR-BH-TSB-4-1525 organised?▾
What spans and capacities do the Telescopic Spreader Beams — 4 t to 16 t cover?▾
How fine is the adjustment on the Telescopic Spreader Beams — 4 t to 16 t?▾
What is the working load limit of the Telescopic Spreader Beams — 4 t to 16 t?▾
What are the Telescopic Spreader Beams — 4 t to 16 t made of?▾
What standard and documents apply to the Telescopic Spreader Beams — 4 t to 16 t?▾
Which shackles and slings suit the Telescopic Spreader Beams — 4 t to 16 t?▾
How should the Telescopic Spreader Beams — 4 t to 16 t be rigged?▾
Telescopic or modular spreader beam: how do the Telescopic Spreader Beams — 4 t to 16 t compare?▾
Can you ship the Telescopic Spreader Beams — 4 t to 16 t outside the UAE?▾
What is the lead time on the Telescopic Spreader Beams — 4 t to 16 t?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog
Written about this part
Lifting & rigging
Spreader beam vs lifting beam: how each carries the load, and how to choose
A lifting beam hangs from one top point and carries the load in bending. A spreader beam hangs from two top slings and only holds them apart, in compression. That one difference decides the weight of the beam, the headroom it needs and the loads it suits.
7 min read
Lifting & rigging
Sling angle compression force: why an angled sling pulls harder, and what it does to the load
An angled sling has to pull sideways as well as up, so it always carries more than its share of the weight. The sideways part squeezes the load between the lifting points. How to find both forces with one triangle, the mistake that doubles the compression, and how a spreader beam takes it out of the load.
6 min read
Lifting & rigging
Bolted flange vs end cap spreader beams: two modular systems, and why rules decide between them
Modular spreader beams come in two families. Bolted-flange systems join end units and fixed-length struts with flange bolts; end-cap systems pin two end fittings into a length of pipe. How each is built, what each does well, and why the question of who supplies the pipe matters more than the engineering.
6 min read








