Skip to content
SUN HYDRAULICSIH-SUN-PR-B

Sun Hydraulics Direct-Acting, Pressure Reducing/Relieving Valve — PRBB, PRDB, PRFB, PRHB, PRJB, Series 0 to 4

Relief, Reducing & Sequence CartridgesEx-stock · delivery in 3 days
Sun Hydraulics PRDB direct-acting pressure reducing/relieving valve, series 1, T-11A cavity — dimension drawing
VIEW 01·Sun Hydraulics PRDB direct-acting pressure reducing/relieving valve, series 1, T-11A cavity — dimension drawing
1 / 3

Sun Hydraulics direct-acting pressure reducing/relieving valve: PRBB, PRDB, PRFB, PRHB, PRJB, series 0 to 4, 5 gpm to 80 gpm (20 L/min to 320 L/min), T-163A, T-11A, T-2A, T-17A, T-19A cavities. Authorised Sun Hydraulics distributor, UAE — supplied direct from Sun.

Key features

  • Valve function: Direct-Acting Pressure Reducing/Relieving Valve
  • Capacity: 5 gpm to 80 gpm (20 L/min to 320 L/min)
  • Max operating pressure: 5000 psi (350 bar)
  • Cavity: T-163A, T-11A, T-2A, T-17A, T-19A
Valve function
Direct-Acting Pressure Reducing/Relieving Valve
Series (frame sizes)
0 to 4
Cavity
T-163A, T-11A, T-2A, T-17A, T-19A
Ships in 24h
Order before 14:00 GST · Jebel Ali
24-month warranty
Manufacturer-backed · genuine parts
Engineering support
A real applications engineer

Product description

A direct-acting reducing/relieving cartridge holds a steady reduced pressure at port 1 from a higher supply at port 2 and, if anything drives port 1 above the setting, relieves it to tank at port 3 at full flow. A damped spool keeps it stable at high reduced pressures.

Sizes and cavities

Sun Hydraulics builds this valve in 5 sizes. The series sets the cavity it screws into and its flow capacity:

  • PRBB — series 0, T-163A cavity, 5 gpm (20 L/min), 0-series
  • PRDB — series 1, T-11A cavity, 10 gpm (40 L/min)
  • PRFB — series 2, T-2A cavity, 20 gpm (80 L/min)
  • PRHB — series 3, T-17A cavity, 40 gpm (160 L/min)
  • PRJB — series 4, T-19A cavity, 80 gpm (320 L/min)

Sun builds its cartridges in frame sizes called series, from the small series 0 to series 4. The series fixes the cavity the valve screws into, so every function in one series shares that cavity, and a larger series carries more flow. Choose the smallest series that passes your flow at an acceptable pressure drop, using the performance curves, then the configuration options for control, setting and seals. If you are replacing a valve, the model code stamped on it gives the series and function directly, and the seal kits listed further down fit that series.

Ratings

  • Maximum operating pressure: 5000 psi (350 bar)
  • Maximum leakage: 2 in³/min. (30 cc/min), 3 in³/min. (50 cc/min), 4 in³/min. (65 cc/min), 5 in³/min. (80 cc/min)

Configuration options

The letters after the base model code choose these options (shown for PRDB; a size may add or drop a choice):

  • Control: L — Standard Screw Adjustment, C — Tamper Resistant - Factory Set, K — Handknob, Y — Tri-Grip Handknob, O — Handknob with Panel Mount, W — Hex Wrench Adjustment
  • Setting range: A — 500 - 3000 psi (35 - 210 bar), 700 psi (50 bar) Standard Setting, W — 750 - 4500 psi (50 - 315 bar), 1000 psi (70 bar) Standard Setting, B — 50 - 1500 psi (3,5 - 105 bar), 200 psi (14 bar) Standard Setting, D — 25 - 800 psi (1,7 - 55 bar), 200 psi (14 bar) Standard Setting, E — 25 - 400 psi (1,7 - 28 bar), 200 psi (14 bar) Standard Setting, S — 25 - 200 psi (1,7 - 14 bar), 100 psi (7 bar) Standard Setting
  • Seal material: N — Buna-N, L — Extended Temp. Buna, V — Viton, E — EPDM
  • Material / coating: /AP — Stainless Steel, Passivated, /LH — Mild Steel, Zinc-Nickel

Option rules: EPDM seals are not allowed on modifier /LH; If the modifier is /AP, the control must be C or L; If the modifier is /LH, the control must be C or L; If the seal is E, the control must be C,K,L,O,W or Y.

Selection notes

  • With no pilot flow, it adds very little leakage to the secondary circuit — a good fit for accumulator circuits.
  • Every spring range is tested at 5,000 psi (350 bar) inlet pressure.
  • Full reverse flow from port 1 to port 2 can close the spool; add a check if reverse flow is needed.

Where it is used

Accumulator circuits, brake and clutch supplies and any branch that must not exceed its pressure.

Installation and seal kits

Valve hex 3/4 in. (19,1 mm), 7/8 in. (22,2 mm), 1 1/8 in. (28,6 mm), 1 1/4 in. (31,8 mm), 1 5/8 in. (41,3 mm); installation torque 20 - 25 lbf ft (27 - 33 Nm), 30 - 35 lbf ft (41 - 47 Nm), 45 - 50 lbf ft (61 - 68 Nm), 150 - 160 lbf ft (203 - 217 Nm), 350 - 375 lbf ft (474 - 508 Nm). Replacement seal kits — series 0: Buna: 990163007, EPDM: 990163014, Viton: 990163006; series 1: Buna: 990011007, EPDM: 990011014, Polyurethane: 990011002, Viton: 990011006; series 2: Buna: 990202007, Polyurethane: 990002002, Viton: 990202006; series 3: Buna: 990017007, EPDM: 990017014, Polyurethane: 990017002, Viton: 990017006; series 4: Buna: 990019007, Polyurethane: 990019002, Viton: 990019006.

Ordering

Indus Hydraulics is an authorised Sun Hydraulics distributor in the UAE and supplies the range direct from Sun Hydraulics. Quote the base model and its configuration letters — for example PRDBLAN — or send us the flow, pressure and duty and we select the valve. We confirm the full ordering code with the quotation.

Identification

ParameterValue
Valve functionDirect-Acting Pressure Reducing/Relieving Valve
Series (frame sizes)0 to 4
CavityT-163A, T-11A, T-2A, T-17A, T-19A

Performance

ParameterValue
Capacity5 gpm to 80 gpm (20 L/min to 320 L/min)
Max operating pressure5000 psi (350 bar)
Setting rangeA — 500 - 3000 psi (35 - 210 bar), 700 psi (50 bar) Standard Setting, W — 750 - 4500 psi (50 - 315 bar), 1000 psi (70 bar) Standard Setting, B — 50 - 1500 psi (3,5 - 105 bar), 200 psi (14 bar) Standard Setting, D — 25 - 800 psi (1,7 - 55 bar), 200 psi (14 bar) Standard Setting, E — 25 - 400 psi (1,7 - 28 bar), 200 psi (14 bar) Standard Setting, S — 25 - 200 psi (1,7 - 14 bar), 100 psi (7 bar) Standard Setting
Max leakage2 in³/min. (30 cc/min), 3 in³/min. (50 cc/min), 4 in³/min. (65 cc/min), 5 in³/min. (80 cc/min)

Configuration

ParameterValue
Control / adjustmentL — Standard Screw Adjustment, C — Tamper Resistant - Factory Set, K — Handknob, Y — Tri-Grip Handknob, O — Handknob with Panel Mount, W — Hex Wrench Adjustment
Seal materialN — Buna-N, L — Extended Temp. Buna, V — Viton, E — EPDM
Material / coating/AP — Stainless Steel, Passivated, /LH — Mild Steel, Zinc-Nickel

Installation

ParameterValue
Valve hex size3/4 in. (19,1 mm), 7/8 in. (22,2 mm), 1 1/8 in. (28,6 mm), 1 1/4 in. (31,8 mm), 1 5/8 in. (41,3 mm)
Installation torque20 - 25 lbf ft (27 - 33 Nm), 30 - 35 lbf ft (41 - 47 Nm), 45 - 50 lbf ft (61 - 68 Nm), 150 - 160 lbf ft (203 - 217 Nm), 350 - 375 lbf ft (474 - 508 Nm)
Seal kitsseries 0: Buna: 990163007, EPDM: 990163014, Viton: 990163006; series 1: Buna: 990011007, EPDM: 990011014, Polyurethane: 990011002, Viton: 990011006; series 2: Buna: 990202007, Polyurethane: 990002002, Viton: 990202006; series 3: Buna: 990017007, EPDM: 990017014, Polyurethane: 990017002, Viton: 990017006; series 4: Buna: 990019007, Polyurethane: 990019002, Viton: 990019006
Weight.30 lb (0,15 kg) to 3.10 lb (1,40 kg)

Shipping & lead time

Lead TimeEx-stock from Dubai — delivered within 3 working days in the UAE. Export orders ship on the lane stated for the destination.

Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations

Also known as

The same part, in the designations used across European and Gulf trade catalogues.

de
Reduzierung
fr
réducteur
es
reductor
it
riduzione
RELATED · OFTEN PAIRED WITH

Engineers viewing this also looked at