Sun Hydraulics 2.3:1 Pilot Ratio Counterbalance Valve — CBBL to CBIL, Series 1 to 4

Sun Hydraulics counterbalance valve, 2.3:1 pilot ratio: CBBL to CBIL, series 1 to 4, 10 gpm to 120 gpm (40 L/min to 480 L/min), T-11A, T-2A, T-17A, T-19A cavities. Authorised Sun Hydraulics distributor, UAE — supplied direct from Sun.
Key features
- Valve function: Counterbalance Valve
- Capacity: 10 gpm to 120 gpm (40 L/min to 480 L/min)
- Max operating pressure: Max setting 5000 psi (350 bar)
- Cavity: T-11A, T-2A, T-17A, T-19A
- Valve function
- Counterbalance Valve
- Series (frame sizes)
- 1 to 4
- Cavity
- T-11A, T-2A, T-17A, T-19A
Product description
A counterbalance valve stops an overrunning load from running away and lowers it under control. Flow into the actuator passes freely through an integral check (port 2 to port 1). Flow out of the actuator is held by a direct-acting relief stage set above the load (port 1 to port 2) until pilot pressure at port 3, taken from the opposite side of the actuator, lowers the effective setting in proportion to the pilot ratio. Other names for it are over-centre valve and motion control valve.
Sizes and cavities
Sun Hydraulics builds this valve in 7 sizes. The series sets the cavity it screws into and its flow capacity:
- CBBL — series 1, T-11A cavity, 10 gpm (40 L/min), semi-restrictive
- CBCL — series 1, T-11A cavity, 15 gpm (60 L/min), standard capacity
- CBDL — series 2, T-2A cavity, 20 gpm (80 L/min), semi-restrictive
- CBEL — series 2, T-2A cavity, 30 gpm (120 L/min), standard capacity
- CBFL — series 3, T-17A cavity, 40 gpm (160 L/min), semi-restrictive
- CBGL — series 3, T-17A cavity, 60 gpm (240 L/min), standard capacity
- CBIL — series 4, T-19A cavity, 120 gpm (480 L/min), standard capacity
Sun builds its cartridges in frame sizes called series, from the small series 0 to series 4. The series fixes the cavity the valve screws into, so every function in one series shares that cavity, and a larger series carries more flow. Choose the smallest series that passes your flow at an acceptable pressure drop, using the performance curves, then the configuration options for control, setting and seals. If you are replacing a valve, the model code stamped on it gives the series and function directly, and the seal kits listed further down fit that series.
Ratings
- Pilot ratio: 2.3:1
- Maximum setting: 5000 psi (350 bar)
- Maximum recommended load pressure at maximum setting: 3850 psi (270 bar)
- Maximum leakage: 5 drops/min. (0,3 cc/min)
- Reseat: >85% of setting
Configuration options
The letters after the base model code choose these options (shown for CBCL; a size may add or drop a choice):
- Control: L — Standard Screw Adjustment, C — Tamper Resistant - Factory Set, R — Lockwired Screw Adjustment
- Setting range: J — 2000 - 5000 psi w/25 psi Check (140 - 350 bar w/ 1,7 bar Check), 3000 psi (210 bar) Standard Setting, C — 2000 - 5000 psi w/4 psi Check (140 - 350 bar w/ 0,3 bar Check), 3000 psi (210 bar) Standard Setting, D — 1000 - 2500 psi w/4 psi Check (70 - 175 bar w/ 0,3 bar Check), 2000 psi (140 bar) Standard Setting, K — 1000 - 2500 psi w/25 psi Check (70 - 175 bar w/ 1,7 bar Check), 2000 psi (140 bar) Standard Setting
- Seal material: N — Buna-N, V — Viton, E — EPDM
- Material / coating: /AP — Stainless Steel, Passivated, /LH — Mild Steel, Zinc-Nickel
Option rules: If the modifier is /AP, the control must be C, L or R; If the modifier is /LH, the control must be L; If the seal is E, the control must be C or L.
Selection notes
- Set it at least 1.3 times the highest load-induced pressure.
- Back-pressure at port 2 adds to the effective setting, multiplied by one plus the pilot ratio — use a vented version where the return line carries back-pressure.
- Turning the adjusting screw clockwise lowers the setting and releases the load.
- Reseats above 85% of the setting when standard set.
- The cartridge can be screwed directly into a cavity machined in the actuator body for extra protection and stiffness.
Where it is used
Booms, jibs and winches on mobile cranes, aerial work platforms and man-lifts, drilling-rig and deck-machinery cylinders, and any actuator that can be driven by its load.
Installation and seal kits
Valve hex 7/8 in. (22,2 mm), 1 1/8 in. (28,6 mm), 1 1/4 in. (31,8 mm), 1 5/8 in. (41,3 mm); installation torque 30 - 35 lbf ft (41 - 47 Nm), 45 - 50 lbf ft (61 - 68 Nm), 150 - 160 lbf ft (203 - 217 Nm), 350 - 375 lbf ft (474 - 508 Nm). Replacement seal kits — series 1: Buna: 990011007, Polyurethane: 990011002, Viton: 990011006, EPDM: 990011014; series 2: Buna: 990202007, Polyurethane: 990002002, Viton: 990202006; series 3: Buna: 990017007, Polyurethane: 990017002, Viton: 990017006, EPDM: 990017014; series 4: Buna: 990019007, Polyurethane: 990019002, Viton: 990019006.
Ordering
Indus Hydraulics is an authorised Sun Hydraulics distributor in the UAE and supplies the range direct from Sun Hydraulics. Quote the base model and its configuration letters — for example CBCLLJN — or send us the flow, pressure and duty and we select the valve. We confirm the full ordering code with the quotation.
Installation
| Parameter | Value |
|---|---|
| Valve hex size | 7/8 in. (22,2 mm), 1 1/8 in. (28,6 mm), 1 1/4 in. (31,8 mm), 1 5/8 in. (41,3 mm) |
| Installation torque | 30 - 35 lbf ft (41 - 47 Nm), 45 - 50 lbf ft (61 - 68 Nm), 150 - 160 lbf ft (203 - 217 Nm), 350 - 375 lbf ft (474 - 508 Nm) |
| Seal kits | series 1: Buna: 990011007, Polyurethane: 990011002, Viton: 990011006, EPDM: 990011014; series 2: Buna: 990202007, Polyurethane: 990002002, Viton: 990202006; series 3: Buna: 990017007, Polyurethane: 990017002, Viton: 990017006, EPDM: 990017014; series 4: Buna: 990019007, Polyurethane: 990019002, Viton: 990019006 |
| Weight | .40 lb (0,20 kg) to 3.00 lb (1,35 kg) |
Identification
| Parameter | Value |
|---|---|
| Valve function | Counterbalance Valve |
| Series (frame sizes) | 1 to 4 |
| Cavity | T-11A, T-2A, T-17A, T-19A |
Configuration
| Parameter | Value |
|---|---|
| Control / adjustment | L — Standard Screw Adjustment, C — Tamper Resistant - Factory Set, R — Lockwired Screw Adjustment |
| Seal material | N — Buna-N, V — Viton, E — EPDM |
| Material / coating | /AP — Stainless Steel, Passivated, /LH — Mild Steel, Zinc-Nickel |
Performance
| Parameter | Value |
|---|---|
| Capacity | 10 gpm to 120 gpm (40 L/min to 480 L/min) |
| Max operating pressure | Max setting 5000 psi (350 bar) |
| Pilot ratio | 2.3:1 |
| Setting range | J — 2000 - 5000 psi w/25 psi Check (140 - 350 bar w/ 1,7 bar Check), 3000 psi (210 bar) Standard Setting, C — 2000 - 5000 psi w/4 psi Check (140 - 350 bar w/ 0,3 bar Check), 3000 psi (210 bar) Standard Setting, D — 1000 - 2500 psi w/4 psi Check (70 - 175 bar w/ 0,3 bar Check), 2000 psi (140 bar) Standard Setting, K — 1000 - 2500 psi w/25 psi Check (70 - 175 bar w/ 1,7 bar Check), 2000 psi (140 bar) Standard Setting |
| Max leakage | 5 drops/min. (0,3 cc/min) |
Shipping & lead time
Sizes & part numbers
7 sizes- Sun Hydraulics part no.CBBL
- Description
- Semi-restrictive
- Series
- 1
- Cavity
- T-11A
- Capacity
- 10 gpm / 40 L/min
- Sun Hydraulics part no.CBCL
- Description
- Standard capacity
- Series
- 1
- Cavity
- T-11A
- Capacity
- 15 gpm / 60 L/min
- Sun Hydraulics part no.CBDL
- Description
- Semi-restrictive
- Series
- 2
- Cavity
- T-2A
- Capacity
- 20 gpm / 80 L/min
- Sun Hydraulics part no.CBEL
- Description
- Standard capacity
- Series
- 2
- Cavity
- T-2A
- Capacity
- 30 gpm / 120 L/min
- Sun Hydraulics part no.CBFL
- Description
- Semi-restrictive
- Series
- 3
- Cavity
- T-17A
- Capacity
- 40 gpm / 160 L/min
- Sun Hydraulics part no.CBGL
- Description
- Standard capacity
- Series
- 3
- Cavity
- T-17A
- Capacity
- 60 gpm / 240 L/min
- Sun Hydraulics part no.CBIL
- Description
- Standard capacity
- Series
- 4
- Cavity
- T-19A
- Capacity
- 120 gpm / 480 L/min
Description — What this part number is, as the manufacturer lists it. Series — Frame size the cartridge is built in, as the maker numbers it; one series shares one cavity size. Cavity — Cavity the cartridge screws into, as the maker designates it. Capacity — Rated flow capacity as published, in US and metric units.
Part numbers are the maker’s base model codes. The full ordering code adds letters for the control, setting range, seal and material options, and we confirm it with the quotation. Capacity and pressure are the maker’s published ratings for the cartridge; check them against the cavity body and the rest of the circuit.
What is the Sun 2.3:1 Pilot Ratio Counterbalance Valve (CBBL, CBCL, CBDL and others) and what does it do?▾
How do I read the Sun model code for the Sun 2.3:1 Pilot Ratio Counterbalance Valve (CBBL, CBCL, CBDL and others)?▾
What sizes and flow capacities does the Sun 2.3:1 Pilot Ratio Counterbalance Valve come in?▾
What pressure and setting range does the Sun 2.3:1 Pilot Ratio Counterbalance Valve have?▾
Which seal and material options does the Sun 2.3:1 Pilot Ratio Counterbalance Valve come with?▾
How is the Sun 2.3:1 Pilot Ratio Counterbalance Valve adjusted, and which control options are offered?▾
Which seal kit fits the Sun 2.3:1 Pilot Ratio Counterbalance Valve (CBBL, CBCL, CBDL and others)?▾
Which cavity and installation torque does the Sun 2.3:1 Pilot Ratio Counterbalance Valve need?▾
Where is the Sun 2.3:1 Pilot Ratio Counterbalance Valve used?▾
How does the Sun 2.3:1 Pilot Ratio Counterbalance Valve differ from the Sun 2:1 Pilot Ratio Counterbalance Valve?▾
Will the Sun 2.3:1 Pilot Ratio Counterbalance Valve stop the load drifting?▾
Can I buy the Sun 2.3:1 Pilot Ratio Counterbalance Valve from stock in the UAE and get a quotation?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations








