Skip to content
SUN HYDRAULICSIH-SUN-CB-H

Sun Hydraulics 10:1 Pilot Ratio Counterbalance Valve — CBAH, CBCH, CBEH, CBGH, CBIH, Series 1 to 4

Counterbalance & Load-Holding ValvesEx-stock · delivery in 3 days
Sun Hydraulics CBCH counterbalance valve, series 1, T-11A cavity — dimension drawing
VIEW 01·Sun Hydraulics CBCH counterbalance valve, series 1, T-11A cavity — dimension drawing
1 / 3

Sun Hydraulics counterbalance valve, 10:1 pilot ratio: CBAH, CBCH, CBEH, CBGH, CBIH, series 1 to 4, 2.5 gpm to 120 gpm (10 L/min to 480 L/min), T-11A, T-2A, T-17A, T-19A cavities. Authorised Sun Hydraulics distributor, UAE — supplied direct from Sun.

Key features

  • Valve function: Counterbalance Valve
  • Capacity: 2.5 gpm to 120 gpm (10 L/min to 480 L/min)
  • Max operating pressure: Max setting 5000 psi (350 bar)
  • Cavity: T-11A, T-2A, T-17A, T-19A
Valve function
Counterbalance Valve
Series (frame sizes)
1 to 4
Cavity
T-11A, T-2A, T-17A, T-19A
Ships in 24h
Order before 14:00 GST · Jebel Ali
24-month warranty
Manufacturer-backed · genuine parts
Engineering support
A real applications engineer

Product description

A counterbalance valve stops an overrunning load from running away and lowers it under control. Flow into the actuator passes freely through an integral check (port 2 to port 1). Flow out of the actuator is held by a direct-acting relief stage set above the load (port 1 to port 2) until pilot pressure at port 3, taken from the opposite side of the actuator, lowers the effective setting in proportion to the pilot ratio. Other names for it are over-centre valve and motion control valve.

Sizes and cavities

Sun Hydraulics builds this valve in 5 sizes. The series sets the cavity it screws into and its flow capacity:

  • CBAH — series 1, T-11A cavity, 2.5 gpm (10 L/min), ultra-restrictive
  • CBCH — series 1, T-11A cavity, 15 gpm (60 L/min), standard capacity
  • CBEH — series 2, T-2A cavity, 30 gpm (120 L/min), standard capacity
  • CBGH — series 3, T-17A cavity, 60 gpm (240 L/min), standard capacity
  • CBIH — series 4, T-19A cavity, 120 gpm (480 L/min), standard capacity

Sun builds its cartridges in frame sizes called series, from the small series 0 to series 4. The series fixes the cavity the valve screws into, so every function in one series shares that cavity, and a larger series carries more flow. Choose the smallest series that passes your flow at an acceptable pressure drop, using the performance curves, then the configuration options for control, setting and seals. If you are replacing a valve, the model code stamped on it gives the series and function directly, and the seal kits listed further down fit that series.

Ratings

  • Pilot ratio: 10:1
  • Maximum setting: 5000 psi (350 bar)
  • Maximum recommended load pressure at maximum setting: 3850 psi (270 bar)
  • Maximum leakage: 5 drops/min. (0,3 cc/min)
  • Reseat: >85% of setting

Configuration options

The letters after the base model code choose these options (shown for CBCH; a size may add or drop a choice):

  • Control: C — Tamper Resistant - Factory Set, L — Standard Screw Adjustment, R — Lockwired Screw Adjustment
  • Setting range: C — 2000 - 5000 psi w/4 psi Check (140 - 350 bar w/ 0,3 bar Check), 3000 psi (210 bar) Standard Setting, D — 1000 - 2500 psi w/4 psi Check (70 - 175 bar w/ 0,3 bar Check), 2000 psi (140 bar) Standard Setting, J — 2000 - 5000 psi w/25 psi Check (140 - 350 bar w/ 1,7 bar Check), 3000 psi (210 bar) Standard Setting, K — 1000 - 2500 psi w/25 psi Check (70 - 175 bar w/ 1,7 bar Check), 2000 psi (140 bar) Standard Setting
  • Seal material: N — Buna-N, V — Viton, E — EPDM
  • Material / coating: /AP — Stainless Steel, Passivated, /LH — Mild Steel, Zinc-Nickel

Option rules: If the modifier is /AP, the control must be C, L or R; If the modifier is /LH, the control must be C or L; If the seal is E, the control must be C or L.

Selection notes

  • Set it at least 1.3 times the highest load-induced pressure.
  • Back-pressure at port 2 adds to the effective setting, multiplied by one plus the pilot ratio — use a vented version where the return line carries back-pressure.
  • Turning the adjusting screw clockwise lowers the setting and releases the load.
  • Reseats above 85% of the setting when standard set.
  • The cartridge can be screwed directly into a cavity machined in the actuator body for extra protection and stiffness.

Where it is used

Booms, jibs and winches on mobile cranes, aerial work platforms and man-lifts, drilling-rig and deck-machinery cylinders, and any actuator that can be driven by its load.

Installation and seal kits

Valve hex 7/8 in. (22,2 mm), 1 1/8 in. (28,6 mm), 1 1/4 in. (31,8 mm), 1 5/8 in. (41,3 mm); installation torque 30 - 35 lbf ft (41 - 47 Nm), 45 - 50 lbf ft (61 - 68 Nm), 150 - 160 lbf ft (203 - 217 Nm), 350 - 375 lbf ft (474 - 508 Nm). Replacement seal kits — series 1: Buna: 990011007, Polyurethane: 990011002, Viton: 990011006, EPDM: 990011014; series 2: Buna: 990202007, Polyurethane: 990002002, Viton: 990202006; series 3: Buna: 990017007, Polyurethane: 990017002, Viton: 990017006; series 4: Buna: 990019007, EPDM: 990019014, Polyurethane: 990019002, Viton: 990019006.

Ordering

Indus Hydraulics is an authorised Sun Hydraulics distributor in the UAE and supplies the range direct from Sun Hydraulics. Quote the base model and its configuration letters — for example CBCHLJN — or send us the flow, pressure and duty and we select the valve. We confirm the full ordering code with the quotation.

Installation

ParameterValue
Valve hex size7/8 in. (22,2 mm), 1 1/8 in. (28,6 mm), 1 1/4 in. (31,8 mm), 1 5/8 in. (41,3 mm)
Installation torque30 - 35 lbf ft (41 - 47 Nm), 45 - 50 lbf ft (61 - 68 Nm), 150 - 160 lbf ft (203 - 217 Nm), 350 - 375 lbf ft (474 - 508 Nm)
Seal kitsseries 1: Buna: 990011007, Polyurethane: 990011002, Viton: 990011006, EPDM: 990011014; series 2: Buna: 990202007, Polyurethane: 990002002, Viton: 990202006; series 3: Buna: 990017007, Polyurethane: 990017002, Viton: 990017006; series 4: Buna: 990019007, EPDM: 990019014, Polyurethane: 990019002, Viton: 990019006
Weight.35 lb (0,15 kg) to 3.00 lb (1,35 kg)

Identification

ParameterValue
Valve functionCounterbalance Valve
Series (frame sizes)1 to 4
CavityT-11A, T-2A, T-17A, T-19A

Configuration

ParameterValue
Control / adjustmentC — Tamper Resistant - Factory Set, L — Standard Screw Adjustment, R — Lockwired Screw Adjustment
Seal materialN — Buna-N, V — Viton, E — EPDM
Material / coating/AP — Stainless Steel, Passivated, /LH — Mild Steel, Zinc-Nickel

Performance

ParameterValue
Capacity2.5 gpm to 120 gpm (10 L/min to 480 L/min)
Max operating pressureMax setting 5000 psi (350 bar)
Pilot ratio10:1
Setting rangeC — 2000 - 5000 psi w/4 psi Check (140 - 350 bar w/ 0,3 bar Check), 3000 psi (210 bar) Standard Setting, D — 1000 - 2500 psi w/4 psi Check (70 - 175 bar w/ 0,3 bar Check), 2000 psi (140 bar) Standard Setting, J — 2000 - 5000 psi w/25 psi Check (140 - 350 bar w/ 1,7 bar Check), 3000 psi (210 bar) Standard Setting, K — 1000 - 2500 psi w/25 psi Check (70 - 175 bar w/ 1,7 bar Check), 2000 psi (140 bar) Standard Setting
Max leakage5 drops/min. (0,3 cc/min)

Shipping & lead time

Lead TimeEx-stock from Dubai — delivered within 3 working days in the UAE. Export orders ship on the lane stated for the destination.

Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations

RELATED · OFTEN PAIRED WITH

Engineers viewing this also looked at