Permanent Chaser

Permanent Chaser, in 2 sizes. Indus part numbers.
Key features
- Product type: Permanent Chaser
- Size range: 130 t SWL to 250 t SWL
- Working load limit: 130–250 t
Product description
Permanent chain chaser left on the mooring line.
Sizes
2 sizes, from 130 t SWL to 250 t SWL. Every size has its own Indus part number in the table below. The letters in the table match the dimension drawing.
Safe working loads are as the maker publishes them. A working load is not a breaking load; never load a fitting past its WLL.
Dimensions are typical and can vary slightly between production runs; the drawing sent with the quotation is final.
Specifying
State the SWL and the chain or wire size the tool works on.
Ordering
Quote the Indus part number from the size table, or send the size and rating you need.
Identification
| Parameter | Value |
|---|---|
| Product type | Permanent Chaser |
| Sizes | 2 |
Dimensions
| Parameter | Value |
|---|---|
| Size range | 130 t SWL to 250 t SWL |
Performance
| Parameter | Value |
|---|---|
| Working load limit | 130–250 t |
Shipping & lead time
Sizes & part numbers
2 sizes- Indus part no.IH-MR-AH-PCH-130T
- Size
- 130 t SWL
- WLL (t)
- 130
- Proof load (t)
- 250
- A (mm)
- 1,867
- B (mm)
- 1,245
- C (mm)
- 1,130
- D (mm)
- 838
- E (mm)
- 130
- F (mm)
- 330
- G (mm)
- 203
- H (mm)
- 102
- Indus part no.IH-MR-AH-PCH-250T
- Size
- 250 t SWL
- WLL (t)
- 250
- Proof load (t)
- 350
- A (mm)
- 2,040
- B (mm)
- 1,301
- C (mm)
- 1,130
- D (mm)
- 838
- E (mm)
- 191
- F (mm)
- 406
- G (mm)
- 261
- H (mm)
- 144
Size — Nominal size as the manufacturer states it. WLL — Working load limit — the most the part may carry in service, as the manufacturer rates it. Proof load — Proof or test load the manufacturer applies to the part. A test figure — never a working limit. A — Dimension A on the manufacturer dimension drawing. B — Dimension B on the manufacturer dimension drawing. C — Dimension C on the manufacturer dimension drawing. D — Dimension D on the manufacturer dimension drawing. E — Dimension E on the manufacturer dimension drawing. F — Dimension F on the manufacturer dimension drawing. G — Dimension G on the manufacturer dimension drawing. H — Dimension H on the manufacturer dimension drawing. Ask us for the dimension drawing if you need it stamped.
WLL is the most the part may carry in service. Proof and breaking loads are test figures — never lift to them. Each load is shown in the unit the manufacturer rates the part in, and a size ships with the manufacturer’s test certificate.
What is Permanent Chaser used for?▾
What sizes does Permanent Chaser come in?▾
How do I choose the right size of Permanent Chaser?▾
What SWL does Permanent Chaser have?▾
What material and finish is Permanent Chaser supplied in?▾
What standard and documents apply to Permanent Chaser?▾
What does Permanent Chaser connect to or work with?▾
How should Permanent Chaser be inspected and looked after?▾
What job is Permanent Chaser used for?▾
How does Permanent Chaser differ from J-Chaser?▾
How are Permanent Chaser shipped, and can they be exported from Dubai?▾
Do you keep Permanent Chaser in stock in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog






