Dinamic Oil GB Heavy-Duty Slewing Gearboxes — 195,000 to 460,000 Nm

Dinamic Oil GB slewing gearboxes: 4 frame sizes, nominal output torque 195,000 to 460,000 Nm, pinion or splined output, static brakes for open or closed circuits. Built in Italy. From Indus Hydraulics, authorised Dinamic Oil distributor, UAE.
Key features
- Product type: Slewing gearbox (planetary)
- Series: Dinamic Oil GB
- Execution: Planetary, reinforced output support for pinion drive
- Reduction stages: 3, 4
- Output torque: T2 FEM 195,000 to 460,000 Nm (M5, 15 rpm)
- Reduction ratio: 50 to 1,508:1
- Motor / input: Hydraulic (orbital, axial piston) or electric motor
- Brake: Static negative: low opening pressure or dry version
- Type approval: Design approval on demand (DNV, ABS, RINA, BV, LR, CCS)
- Product type
- Slewing gearbox (planetary)
- Series
- Dinamic Oil GB
- Execution
- Planetary, reinforced output support for pinion drive
- Reduction stages
- 3, 4
- Type approval
- Design approval on demand (DNV, ABS, RINA, BV, LR, CCS)
Product description
The GB slewing gearboxes extend the slewing range above the RE sizes: four frames, GB 12010 to GB 26000, with nominal output torques up to 460,000 Nm in three or four stages, for large offshore and deck cranes, harbour and dockyard cranes and tunnel boring machines. Dinamic Oil builds slewing solutions to order up to about 2,000,000 Nm.
Indus Hydraulics is an authorised Dinamic Oil distributor and supplies direct from Dinamic Oil's factory in Bomporto, Italy.
Ratings
The table gives each size's nominal output torque T2 FEM — Dinamic Oil's figure for F.E.M. class M5 (L2-T5) at 15 rpm output, an indicative value confirmed per application — and the ratio range for each number of stages. The output support has its own static and dynamic torque limits in the catalogue: the lower of the support limit and the gearset's T2max governs, and the static limit must never be exceeded.
Supports and pinions
Supports, shafts and pinions for the GB sizes are not tabulated in the catalogue — they are designed with the order. Send the slewing-ring data (module, number of teeth, profile shift, face width), the radial load and the mounting space, and Dinamic Oil's technical department sizes the output.
Selection
Size the drive on the slewing torque — the ring's friction, wind and inertia loads, divided by the ring-to-pinion ratio and the number of drives on the ring — then check it against T2 FEM for the duty class, and the start-up and braking peaks against the output support's dynamic limit. Large rings often use two or more drives sharing the load.
Approvals
Design approval by DNV, ABS, RINA, Bureau Veritas, Lloyd's Register or CCS is available on demand.
Inputs, brakes and lubrication
Inputs for hydraulic (orbital or axial piston) and electric motors are the same as Dinamic Oil's planetary gearbox range. Static negative brakes come in a low-opening-pressure version for closed-loop circuits and a dry version for high-speed motors. Oil or grease lubrication is available; standard ambient range up to +40 °C.
Options and accessories
- Brakes: static negative brakes in a low-opening-pressure version for closed-loop circuits and a dry version for high-speed motors. See brakes for planetary gearboxes.
- Inputs: hydraulic orbital or axial piston motors, or electric motors, through the planetary range's adapters.
- Outputs: splined or integral pinions, splined or cylindrical shafts; eccentric supports for backlash adjustment; pinions made to your ring-gear data.
- Lubrication: oil or grease.
Identification
| Parameter | Value |
|---|---|
| Product type | Slewing gearbox (planetary) |
| Series | Dinamic Oil GB |
| Execution | Planetary, reinforced output support for pinion drive |
Performance
| Parameter | Value |
|---|---|
| Reduction stages | 3, 4 |
| Output torque | T2 FEM 195,000 to 460,000 Nm (M5, 15 rpm) |
| Reduction ratio | 50 to 1,508:1 |
Construction
| Parameter | Value |
|---|---|
| Motor / input | Hydraulic (orbital, axial piston) or electric motor |
| Brake | Static negative: low opening pressure or dry version |
| Output / mounting | Pinion (splined or integral) or splined / cylindrical shaft; flanged or eccentric support |
| Lubrication | Oil or grease |
Compliance
| Parameter | Value |
|---|---|
| Rating basis | F.E.M. M5 (L2-T5) at 15 rpm, indicative |
| Type approval | Design approval on demand (DNV, ABS, RINA, BV, LR, CCS) |
Supply
| Parameter | Value |
|---|---|
| Made in | Italy (Dinamic Oil S.p.A., Bomporto) |
| Supply | Authorised distributor, direct from the factory |
Shipping & lead time
Sizes & part numbers
4 sizes- Indus part no.IH-DO-SLG-12010
- Description
- GB 12010
- Output torque (Nm)
- 195,000
- Ratio
- 3-stage 53–222; 4-stage 210–1,508
- Indus part no.IH-DO-SLG-16000
- Description
- GB 16000
- Output torque (Nm)
- 297,000
- Ratio
- 3-stage 50–165; 4-stage 181–1,241
- Indus part no.IH-DO-SLG-21000
- Description
- GB 21000
- Output torque (Nm)
- 360,000
- Ratio
- 3-stage 58–140; 4-stage 233–766
- Indus part no.IH-DO-SLG-26000
- Description
- GB 26000
- Output torque (Nm)
- 460,000
- Ratio
- 3-stage 58–108; 4-stage 210–745
Description — What this part number is, as the manufacturer lists it. Output torque — Rated output torque, as the manufacturer publishes it. A circuit is limited by its lowest-rated component. The page states which rating it is. Ratio — Reduction ratio, or the range of ratios the model is built in, as published.
What is the Dinamic Oil GB Heavy-Duty Slewing Gearboxes used for?▾
How do I read a Dinamic Oil model such as GB 21000?▾
Which sizes and torques do the Dinamic Oil GB Heavy-Duty Slewing Gearboxes cover?▾
What is T2 FEM on the Dinamic Oil GB Heavy-Duty Slewing Gearboxes?▾
What torque rating and basis do the Dinamic Oil GB Heavy-Duty Slewing Gearboxes have?▾
What brakes and lubrication do the Dinamic Oil GB Heavy-Duty Slewing Gearboxes use?▾
Do the Dinamic Oil GB Heavy-Duty Slewing Gearboxes carry a class approval?▾
What outputs and supports fit the Dinamic Oil GB Heavy-Duty Slewing Gearboxes?▾
Can the pinion backlash of the Dinamic Oil GB Heavy-Duty Slewing Gearboxes be adjusted?▾
How do the GB slewing gearboxes compare with the RE range?▾
Are the Dinamic Oil GB Heavy-Duty Slewing Gearboxes genuine Dinamic Oil units and can you export them?▾
Do you keep the Dinamic Oil GB Heavy-Duty Slewing Gearboxes in stock in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog

