Skip to content
SUN HYDRAULICSIH-SUN-MW-G

Sun Hydraulics Vented 4.5:1 Pilot Ratio Load-Reactive Load Control Valve — MWEG, MWGG, MWIG, Series 2 to 4

Counterbalance & Load-Holding ValvesEx-stock · delivery in 3 days
Sun Hydraulics MWIG load-reactive load control valve, series 4, T-24A cavity — dimension drawing
VIEW 01·Sun Hydraulics MWIG load-reactive load control valve, series 4, T-24A cavity — dimension drawing
1 / 3

Sun Hydraulics load-reactive load control valve, 4.5:1 pilot ratio: MWEG, MWGG, MWIG, series 2 to 4, 30 gpm to 120 gpm (120 L/min to 480 L/min), T-22A, T-23A, T-24A cavities. Authorised Sun Hydraulics distributor, UAE — supplied direct from Sun.

Key features

  • Valve function: Load-Reactive Load Control Valve
  • Capacity: 30 gpm to 120 gpm (120 L/min to 480 L/min)
  • Max operating pressure: 5000 psi (350 bar)
  • Cavity: T-22A, T-23A, T-24A
Valve function
Load-Reactive Load Control Valve
Series (frame sizes)
2 to 4
Cavity
T-22A, T-23A, T-24A
Ships in 24h
Order before 14:00 GST · Jebel Ali
24-month warranty
Manufacturer-backed · genuine parts
Engineering support
A real applications engineer

Product description

A 3-port load control valve that works like a counterbalance valve: an integral check gives free flow into the actuator (port 2 to port 1) and a pilot-assisted relief stage holds the load (port 1 to port 2) until pilot pressure at port 3 lowers its setting by the pilot ratio. It seats as a poppet for tight holding and meters as a spool for smooth lowering.

Sizes and cavities

Sun Hydraulics builds this valve in 3 sizes. The series sets the cavity it screws into and its flow capacity:

  • MWEG — series 2, T-22A cavity, 30 gpm (120 L/min)
  • MWGG — series 3, T-23A cavity, 60 gpm (240 L/min)
  • MWIG — series 4, T-24A cavity, 120 gpm (480 L/min)

Sun builds its cartridges in frame sizes called series, from the small series 0 to series 4. The series fixes the cavity the valve screws into, so every function in one series shares that cavity, and a larger series carries more flow. Choose the smallest series that passes your flow at an acceptable pressure drop, using the performance curves, then the configuration options for control, setting and seals. If you are replacing a valve, the model code stamped on it gives the series and function directly, and the seal kits listed further down fit that series.

Ratings

  • Pilot ratio: 4.5:1
  • Maximum operating pressure: 5000 psi (350 bar)
  • Maximum leakage: 5 drops/min. (0,3 cc/min)
  • Reseat: ≥77% of setting
  • Check cracking pressure: 25 psi (1,7 bar)

Configuration options

The letters after the base model code choose these options (shown for MWIG; a size may add or drop a choice):

  • Control: L — Standard Screw Adjustment
  • Setting range: H — 1000 - 4000 psi (70 - 280 bar), 3000 psi (210 bar) Standard Setting, J — 2000 - 5000 psi (140 - 350 bar), 3000 psi (210 bar) Standard Setting
  • Seal material: N — Buna-N, V — Viton
  • Material / coating: /AP — Stainless Steel, Passivated, /LH — Mild Steel, Zinc-Nickel

Option rules: If the modifier is /AP, the control must be L; If the modifier is /LH, the control must be L.

Selection notes

  • Set it at least 1.3 times the highest load-induced pressure, or 1.5 times where the setting is below 2,000 psi (140 bar).
  • Back-pressure at port 2 adds to the effective setting, multiplied by one plus the pilot ratio — the vented versions avoid this.
  • Turning the adjusting screw clockwise lowers the setting.

Where it is used

Load holding on large cylinders and motors in mobile and industrial machines, where higher flow is needed.

Installation and seal kits

Valve hex 1 1/8 in. (28,6 mm), 1 1/4 in. (31,8 mm), 1 5/8 in. (41,3 mm); installation torque 45 - 50 lbf ft (61 - 68 Nm), 150 - 160 lbf ft (203 - 217 Nm), 350 - 375 lbf ft (474 - 508 Nm). Replacement seal kits — series 2: Buna: 990022007, Polyurethane: 990022002, Viton: 990022006; series 3: Buna: 990023007, Polyurethane: 990023002, Viton: 990023006; series 4: Buna: 990024007, Polyurethane: 990024002, Viton: 990024006.

Ordering

Indus Hydraulics is an authorised Sun Hydraulics distributor in the UAE and supplies the range direct from Sun Hydraulics. Quote the base model and its configuration letters — for example MWIGLHN — or send us the flow, pressure and duty and we select the valve. We confirm the full ordering code with the quotation.

Performance

ParameterValue
Capacity30 gpm to 120 gpm (120 L/min to 480 L/min)
Max operating pressure5000 psi (350 bar)
Pilot ratio4.5:1
Setting rangeH — 1000 - 4000 psi (70 - 280 bar), 3000 psi (210 bar) Standard Setting, J — 2000 - 5000 psi (140 - 350 bar), 3000 psi (210 bar) Standard Setting
Max leakage5 drops/min. (0,3 cc/min)

Installation

ParameterValue
Valve hex size1 1/8 in. (28,6 mm), 1 1/4 in. (31,8 mm), 1 5/8 in. (41,3 mm)
Installation torque45 - 50 lbf ft (61 - 68 Nm), 150 - 160 lbf ft (203 - 217 Nm), 350 - 375 lbf ft (474 - 508 Nm)
Seal kitsseries 2: Buna: 990022007, Polyurethane: 990022002, Viton: 990022006; series 3: Buna: 990023007, Polyurethane: 990023002, Viton: 990023006; series 4: Buna: 990024007, Polyurethane: 990024002, Viton: 990024006

Identification

ParameterValue
Valve functionLoad-Reactive Load Control Valve
Series (frame sizes)2 to 4
CavityT-22A, T-23A, T-24A

Configuration

ParameterValue
Control / adjustmentL — Standard Screw Adjustment
Seal materialN — Buna-N, V — Viton
Material / coating/AP — Stainless Steel, Passivated, /LH — Mild Steel, Zinc-Nickel

Shipping & lead time

Lead TimeEx-stock from Dubai — delivered within 3 working days in the UAE. Export orders ship on the lane stated for the destination.

Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations

RELATED · OFTEN PAIRED WITH

Engineers viewing this also looked at