Sun Hydraulics Balanced Load Control Valve — MBIM

Sun Hydraulics balanced load control valve: MBIM, series 4, 120 gpm (480 L/min), T-19A cavity. Authorised Sun Hydraulics distributor, UAE — supplied direct from Sun.
Key features
- Valve function: Balanced Load Control Valve
- Capacity: 120 gpm (480 L/min)
- Max operating pressure: 5000 psi (350 bar)
- Cavity: T-19A
- Valve function
- Balanced Load Control Valve
- Series (frame sizes)
- 4
- Cavity
- T-19A
Product description
A pilot-to-open load control valve with a balanced modulating element and a reverse-flow check. Free flow passes into the actuator through the check (port 2 to port 1); flow out of the actuator is metered by pilot pressure at port 3, and because the element is balanced against load pressure the flow stays steady as the load changes.
Sizes and cavities
Sun Hydraulics builds this valve in 1 size. The series sets the cavity it screws into and its flow capacity:
- MBIM — series 4, T-19A cavity, 120 gpm (480 L/min)
Sun builds its cartridges in frame sizes called series, from the small series 0 to series 4. The series fixes the cavity the valve screws into, so every function in one series shares that cavity, and a larger series carries more flow. Choose the smallest series that passes your flow at an acceptable pressure drop, using the performance curves, then the configuration options for control, setting and seals. If you are replacing a valve, the model code stamped on it gives the series and function directly, and the seal kits listed further down fit that series.
Ratings
- Maximum operating pressure: 5000 psi (350 bar)
- Maximum leakage: See Technical Features
- Check cracking pressure: 25 psi (1,7 bar)
Configuration options
The letters after the base model code choose these options (shown for MBIM; a size may add or drop a choice):
- Control: X — Not Adjustable
- Setting range: E — 75 psi (5 bar), G — 100 psi (7 bar), H — 200 psi (14 bar), I — 300 psi (20 bar), K — 450 psi (33 bar), M — 525 psi (36,7 bar)
- Seal material: N — Buna-N, V — Viton, E — EPDM
- Material / coating: /AP — Stainless Steel, Passivated
Option rules: If the modifier is /AP, the control must be X; If the seal is E, the control must be X.
Selection notes
- It has no relief function, not even thermal relief, so the circuit needs its own protection.
- Performs best metering out, with port 1 to the load and port 2 to tank.
- Back-pressure at port 2 acts directly against the pilot pressure.
- Ordered by minimum control pressure; the lower ranges are not zero-leak.
Where it is used
Meter-out control of large cylinders and motors where speed should follow the pilot signal regardless of load.
Installation and seal kits
Valve hex 1 5/8 in. (41,3 mm); installation torque 350 - 375 lbf ft (474 - 508 Nm).
Ordering
Indus Hydraulics is an authorised Sun Hydraulics distributor in the UAE and supplies the range direct from Sun Hydraulics. Quote the base model and its configuration letters — for example MBIMXKN — or send us the flow, pressure and duty and we select the valve. We confirm the full ordering code with the quotation.
Identification
| Parameter | Value |
|---|---|
| Valve function | Balanced Load Control Valve |
| Series (frame sizes) | 4 |
| Cavity | T-19A |
Installation
| Parameter | Value |
|---|---|
| Valve hex size | 1 5/8 in. (41,3 mm) |
| Installation torque | 350 - 375 lbf ft (474 - 508 Nm) |
Configuration
| Parameter | Value |
|---|---|
| Control / adjustment | X — Not Adjustable |
| Seal material | N — Buna-N, V — Viton, E — EPDM |
| Material / coating | /AP — Stainless Steel, Passivated |
Performance
| Parameter | Value |
|---|---|
| Capacity | 120 gpm (480 L/min) |
| Max operating pressure | 5000 psi (350 bar) |
| Setting range | E — 75 psi (5 bar), G — 100 psi (7 bar), H — 200 psi (14 bar), I — 300 psi (20 bar), K — 450 psi (33 bar), M — 525 psi (36,7 bar) |
| Max leakage | See Technical Features |
Shipping & lead time
Sizes & part numbers
1 size- Sun Hydraulics part no.MBIM
- Series
- 4
- Cavity
- T-19A
- Capacity
- 120 gpm / 480 L/min
- Max pressure
- 5000 psi / 350 bar
Series — Frame size the cartridge is built in, as the maker numbers it; one series shares one cavity size. Cavity — Cavity the cartridge screws into, as the maker designates it. Capacity — Rated flow capacity as published, in US and metric units. Max pressure — Maximum pressure as the maker publishes it, in psi and bar.
Part numbers are the maker’s base model codes. The full ordering code adds letters for the control, setting range, seal and material options, and we confirm it with the quotation. Capacity and pressure are the maker’s published ratings for the cartridge; check them against the cavity body and the rest of the circuit.
What is the Sun Balanced Load Control Valve (MBIM) and what does it do?▾
How do I read the Sun model code for the Sun Balanced Load Control Valve (MBIM)?▾
What sizes and flow capacities does the Sun Balanced Load Control Valve come in?▾
What pressure and setting range does the Sun Balanced Load Control Valve have?▾
Which seal and material options does the Sun Balanced Load Control Valve come with?▾
How is the Sun Balanced Load Control Valve adjusted, and which control options are offered?▾
Which seal kit fits the Sun Balanced Load Control Valve (MBIM)?▾
Which cavity and installation torque does the Sun Balanced Load Control Valve need?▾
Where is the Sun Balanced Load Control Valve used?▾
How does the Sun Balanced Load Control Valve differ from the Sun Vented Balanced Load Control Valve?▾
Does a balanced load control valve protect against over-pressure on the Sun Balanced Load Control Valve?▾
Can I buy the Sun Balanced Load Control Valve from stock in the UAE and get a quotation?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations








