Ferritic and Martensitic Stainless Tubes

Ferritic and martensitic stainless tubes to ASTM A268, including TP405, TP410 and super-ferritic grades, for heat exchangers where chloride stress-corrosion cracking rules out the austenitic grades. Made to ASTM A268 / ASME SA-268, ASTM A803, DIN 17456. Supplied from Dubai with an Indus part number for each size and mill test certificates on request.
Key features
- Product type: Ferritic and Martensitic Stainless Tubes
- Construction: Seamless, cold drawn or hot finished
- Standards: ASTM A268 / ASME SA-268, ASTM A803, DIN 17456
- Base tube material: TP405; TP409; TP410; TP430; TP439; 26-3-3
- Outside diameter: 19.05–25.4 mm
- Wall thickness: 1.65–2.11 mm
- Product type
- Ferritic and Martensitic Stainless Tubes
- Construction
- Seamless, cold drawn or hot finished
- Base tube material
- TP405; TP409; TP410; TP430; TP439; 26-3-3
Product description
Ferritic and martensitic stainless tubes to ASTM A268, including TP405, TP410 and super-ferritic grades, for heat exchangers where chloride stress-corrosion cracking rules out the austenitic grades.
Specification
- ASTM A268 scope: Seamless and welded nominal-wall ferritic/martensitic stainless tube for general corrosion and high-temperature service; TP410 and S41500 hardenable; high-Cr ferritics prone to notch brittleness on slow cooling; TP439 used for hot-water tanks without PWHT
- Final heat treatment (A268): Reheat to 650 °C (1200 °F) or higher and cool as suited to grade; S41500 at 510 °C (950 °F) or higher
- Dimensional tolerances (A268): OD ±0.13 mm below 38.1 mm; ±0.25 mm 38.1–88.9 mm; wall ±15 % below 12.7 mm OD, ±10 % above; cut length +3/−0 mm (to 7.3 m)
- Super-ferritic S44660 (26-3-3): Tensile 585 MPa, yield 450 MPa, elongation 20 %; hardness 265 HBW / 25 HRC max
Standards
ASTM A268 / ASME SA-268, ASTM A803, DIN 17456. Equivalent grades across ASTM, EN, DIN, JIS and GB/T standards are indicative; we check them against each tender.
Materials
- Tube: TP405; TP409; TP410; TP430; TP439; 26-3-3
Testing and documents
- Flattening/flare/hardness/tension per A268 and A1016
- Hydro or electric NDE per A1016
- Mill test certificate to EN 10204 3.1 on request; third-party inspection can be arranged against your inspection and test plan
Where it is used
- Feedwater heaters (TP439 under A803)
Sizes
2 sizes, each under its own Indus part number in the size table. The table gives the range as limits; any size inside it is made to order.
Ordering
Quote the Indus part number from the size table, or send the standard and grade, the outside diameter and wall (BWG or millimetres, minimum or average wall), the length and the quantity. We quote with the mill certificates and the inspection you need.
Identification
| Parameter | Value |
|---|---|
| Product type | Ferritic and Martensitic Stainless Tubes |
| Construction | Seamless, cold drawn or hot finished |
Compliance
| Parameter | Value |
|---|---|
| Standards | ASTM A268 / ASME SA-268, ASTM A803, DIN 17456 |
Construction
| Parameter | Value |
|---|---|
| Base tube material | TP405; TP409; TP410; TP430; TP439; 26-3-3 |
Dimensions
| Parameter | Value |
|---|---|
| Outside diameter | 19.05–25.4 mm |
| Wall thickness | 1.65–2.11 mm |
| Length | Random or fixed lengths; cut to length on request |
| Size table | Size range — discrete sizes on request |
Quality
| Parameter | Value |
|---|---|
| Testing | Flattening/flare/hardness/tension per A268 and A1016; Hydro or electric NDE per A1016 |
| Certification | Mill test certificate to EN 10204 3.1 on request; third-party inspection by arrangement |
Application
| Parameter | Value |
|---|---|
| Typical services | Feedwater heaters (TP439 under A803) |
Shipping & lead time
Sizes & part numbers
2 sizes- Indus part no.IH-TF-SS-FER-0190-165
- O.D. (mm)
- 19.05
- O.D. (in)
- 3/4
- BWG
- 16
- Wall (mm)
- 1.65
- Indus part no.IH-TF-SS-FER-0254-211
- O.D. (mm)
- 25.40
- O.D. (in)
- 1
- BWG
- 14
- Wall (mm)
- 2.11
O.D. (mm) — Outside diameter of the tube or pipe in millimetres. O.D. (in) — The same outside diameter in inches, as the trade orders it. BWG — Birmingham Wire Gauge of the wall, the usual way heat-exchanger tube wall is ordered. Wall (mm) — Wall thickness in millimetres: minimum or average wall per the governing standard and the order.
These are typical sizes for the range, not a full mill list. Other diameters, walls, fin geometries and lengths are made to order: tell us the standard and grade, the O.D. and wall, and the length you need. Mill test certificates to EN 10204 3.1 are available on request.
What are ferritic and martensitic stainless tubes used for?▾
How are the part numbers such as IH-TF-SS-FER-0190-165 read?▾
What sizes do the Ferritic and Martensitic Stainless Tubes come in?▾
What tolerances does ASTM A268 set for ferritic stainless tube?▾
What strength does super-ferritic S44660 (26-3-3) reach?▾
Which grades are available in the Ferritic and Martensitic Stainless Tubes?▾
Which standards and certificates apply to the Ferritic and Martensitic Stainless Tubes?▾
What do the Ferritic and Martensitic Stainless Tubes connect to in a feedwater heater?▾
What heat treatment applies to the Ferritic and Martensitic Stainless Tubes after forming?▾
How do the Ferritic and Martensitic Stainless Tubes differ from austenitic stainless heat exchanger tubes?▾
Can you export the Ferritic and Martensitic Stainless Tubes from Dubai?▾
Is the Ferritic and Martensitic Stainless Tubes available from Indus Hydraulics in Dubai, and what is the lead time?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog


