DEMCO Series NE-D Wafer Butterfly Valve, 4″, 200 psi

4″ (100 mm) DEMCO Series NE-D wafer butterfly valve, 200 psi drop-tight in an ASME Class 150 body. 2 Cameron part numbers: ductile iron and grey cast iron bodies, nickel-plated ductile iron disc, Buna-N seat.
Key features
- Series: NE-D
- Body configuration: Wafer
- ASME pressure class: ASME Class 150 (285 psi non-shock body rating)
- Series
- NE-D
- Body configuration
- Wafer
- Sanitary / FDA service
- no
- Size range
- 4″ (100 mm)
- ASME pressure class
- ASME Class 150 (285 psi non-shock body rating)
- Operating temperature range
- Buna-N: 0°F to +180°F (−18°C to +82°C)
Product description
The 4″ (100 mm) DEMCO Series NE-D wafer butterfly valve is the short-neck wafer with body notches for the lightweight flange patterns used on tank trucks and bulk-handling equipment; it also self-centres in ASME Class 125/150 flanges. This page lists the 2 factory configurations we can supply in this size, each identified by its Cameron part number, with the body, disc, stem and seat it was built with. Every one is rated for 200 psi drop-tight, bi-directional shut-off in an ASME Class 150 body.
Configurations available
| Part number | Body | Disc | Stem | Seat |
|---|---|---|---|---|
J022183-1115311 | Ductile iron | Nickel-plated ductile iron | 416 stainless steel | Buna-N |
J022183-1215311 | Grey cast iron | Nickel-plated ductile iron | 416 stainless steel | Buna-N |
Trim is read from the part number using DEMCO's ordering table. Confirm against the nameplate when we quote.
Reading the part number
Take J022183-1115311. J022183 is the DEMCO base number for a 4″ Series NE-D valve at 200 psi. The suffix is read left to right: body configuration (1 = wafer), body material (1 = ductile iron), stem (1 = 416 stainless steel), disc (5 = nickel-plated ductile iron) and seat (31 = Buna-N). The last character is the operator code.
Performance
- Body rating: ASME Class 150 (285 psi non-shock).
- Shut-off: 200 psi drop-tight, identical from either flow direction.
- Vacuum: sealed against 10 microns (29.9 in Hg).
- Buna-N seat: 0°F to +180°F (−18°C to +82°C).
Construction
- Hard-backed cartridge seat: the elastomer is bonded to a rigid backing ring and can be replaced in the field without special tools.
- Triple stem seal and a dry stem journal keep line fluid out of the stem bore.
- Floating disc centres itself in the seat; the stem is blowout-proof.
- Double-D upper stem and DEMCO top flange accept the full DEMCO actuation range.
- MSS SP-25 marking on every valve.
Installation
The NE-D wafer body is notched for lightweight transport flange patterns and also self-centres between ASME Class 125/150 flanges on through-bolts. A wafer valve is clamped between two flanges and is not rated for end-of-line service.
Operators
The DEMCO top flange takes the 10-position locking handle, worm-gear operator and Series DR pneumatic actuators. Confirm the operator supplied with each part number when we quote.
Supply
Supplied from surplus stock through our supply network. Quantity, unit condition and any documentation are confirmed on the quotation. Put the part number, quantity and delivery point on your RFQ. For the full Series NE-D range, including sizes and trims not listed here, see the DEMCO Series NE-D series page.
Identification
| Parameter | Value |
|---|---|
| Series | NE-D |
| Body configuration | Wafer |
| Sanitary / FDA service | no |
| Cameron part numbers | J022183-1115311, J022183-1215311 |
Dimensions
| Parameter | Value |
|---|---|
| Size range | 4″ (100 mm) |
Performance
| Parameter | Value |
|---|---|
| ASME pressure class | ASME Class 150 (285 psi non-shock body rating) |
| Drop-tight shut-off ratings | 200 psi drop-tight, bi-directional |
| Operating temperature range | Buna-N: 0°F to +180°F (−18°C to +82°C) |
| Vacuum rating | 29.9 in Hg (sealed against 10 microns) |
| End-of-line service capable | no |
| Actuation options | Lever handles, worm-gear operators, Series DR pneumatic actuators |
Compliance
| Parameter | Value |
|---|---|
| End-connection / flange standard | Lightweight flange patterns (transportation/bulk-handling) and ASME Class 125/150 flanges |
Construction
| Parameter | Value |
|---|---|
| Body material options | Ductile iron, grey cast iron |
| Stem material options | 416 stainless steel |
| Disc material options | Nickel-plated ductile iron |
| Seat elastomer options | Buna-N |
Shipping & lead time
What is the 4″ DEMCO NE-D wafer butterfly valve rated 200 psi used for?▾
How do I read DEMCO part number J022183-1115311 on the 4″ NE-D wafer valve?▾
Which configurations of the 4″ DEMCO NE-D wafer butterfly valve can Indus supply?▾
What are the body, disc and seat materials of the 4″ DEMCO NE-D wafer butterfly valve?▾
What pressure does the 4″ DEMCO NE-D wafer butterfly valve hold?▾
What temperature range does the 4″ DEMCO NE-D wafer butterfly valve cover?▾
Which flange standard and marking apply to the 4″ DEMCO NE-D wafer butterfly valve?▾
Can the 4″ DEMCO NE-D wafer butterfly valve be used at the end of a line?▾
Which operators fit the 4″ DEMCO NE-D wafer butterfly valve?▾
4″ DEMCO NE-D or NE-I wafer butterfly valve: which one?▾
Where is the 4″ DEMCO NE-D wafer butterfly valve made and what lead time applies?▾
What is the lead time for the 4″ DEMCO NE-D wafer butterfly valve?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog





