Skip to content
SUN HYDRAULICSIH-SUN-DF-J

Sun Hydraulics 2-Way, 2-Stage, Solenoid-Operated Directional Poppet Valve, Flow 2-1 (740 Series) — DFCJ, DFDJ, DFEJ, DFFJ, Series 1 to 4

Solenoid Cartridge ValvesEx-stock · delivery in 3 days
Sun Hydraulics DFCJ 2-way 2-stage solenoid-operated poppet valve, series 1, T-13A cavity — dimension drawing
VIEW 01·Sun Hydraulics DFCJ 2-way 2-stage solenoid-operated poppet valve, series 1, T-13A cavity — dimension drawing
1 / 3

Sun Hydraulics 2-Way, 2-Stage, Solenoid-Operated Directional Poppet Valve, Flow 2-1 (740 Series): DFCJ, DFDJ, DFEJ, DFFJ, series 1 to 4, 15 gpm to 120 gpm (60 L/min to 480 L/min), T-13A, T-5A, T-16A, T-18A cavities. Authorised Sun Hydraulics distributor, UAE — supplied direct from Sun.

Key features

  • Valve function: 2-Way 2-Stage Solenoid-Operated Poppet Valve
  • Capacity: 15 gpm to 120 gpm (60 L/min to 480 L/min)
  • Max operating pressure: 5000 psi (350 bar)
  • Cavity: T-13A, T-5A, T-16A, T-18A
Valve function
2-Way 2-Stage Solenoid-Operated Poppet Valve
Series (frame sizes)
1 to 4
Cavity
T-13A, T-5A, T-16A, T-18A
Ships in 24h
Order before 14:00 GST · Jebel Ali
24-month warranty
Manufacturer-backed · genuine parts
Engineering support
A real applications engineer

Product description

A pilot-operated, 2-position poppet valve: the solenoid opens a small pilot, and system pressure moves the main poppet, so a small coil switches a large flow. A reverse free-flow check lets oil pass the other way when it is closed. Poppet seating gives very low leakage — under 10 drops a minute at 5,000 psi.

This version

  • Uses Sun's 740 Series coils, or 747 Series coils for hazardous locations.
  • Controls flow from port 2 to port 1.

Sizes and cavities

Sun Hydraulics builds this valve in 4 versions:

  • DFCJ — series 1, T-13A cavity, 15 gpm (60 L/min)
  • DFDJ — series 2, T-5A cavity, 30 gpm (120 L/min)
  • DFEJ — series 3, T-16A cavity, 60 gpm (240 L/min)
  • DFFJ — series 4, T-18A cavity, 120 gpm (480 L/min)

Sun builds its cartridges in frame sizes called series. The series fixes the cavity the valve screws into, so every function in one series shares that cavity, and a larger series carries more flow. Choose the smallest series that passes your flow at an acceptable pressure drop, using the performance curves, then the configuration options. If you are replacing a valve, the model code stamped on it gives the series and function directly, and the seal kits listed further down fit that series.

Ratings

  • Maximum operating pressure: 5000 psi (350 bar)
  • Maximum leakage: 10 drops/min.@5000 psi (0,7 cc/min.@350 bar)
  • Typical response time: 30 ms
  • Switching frequency: 15,000 max. cycles/hr
  • Check cracking pressure: 50 psi (3,5 bar)

Configuration options

The letters after the base model code choose these options (shown for DFCJ; a size may add or drop a choice):

  • Control: D — Twist/Lock (Dual) Manual Override, L — Twist/Lock (Detent) Manual Override, M — Manual Override, T — Twist (Momentary) Manual Override, X — No Manual Override
  • Spool / poppet configuration: C — Normally Closed, H — Normally Open
  • Seal material: N — Buna-N, V — Viton, E — EPDM
  • Coil: 45 coil choices, or no coil — 12 VDC, 14 VDC, 24 VDC, 28 VDC, 115 VAC, 230 VAC; connections include DIN 43650-Form A, AMP Junior Timer, Twin Lead, Metri-Pack, Deutsch DT04-2P, Explosion Proof

Option rules: If the coil is in this group (211, 212, 212D, 214, 214D, 223, 224, 224D, 228, 228D, 612, 612D, 614, 614D, 624, 624D, 628, 712, 712D, 714, 714D, 724, 724D, 728, 728D, 812, 812D, 814, 814D, 824, 824D, 828, 828D, 912, 912D, 914, 914D, 924, 924D, 928, 928D, JM24BD, JM24CD, JN24BD, JN24CD), the range must be C or H; If the coil is in this group (JM24BD, JM24CD, JN24BD, JN24CD), the control must be M or X; If the seal is E, the control must be M or X.

Selection notes

  • Normally open or normally closed, chosen in the code.
  • The solenoid tube is fatigue-rated for 5,000 psi (350 bar).

Where it is used

Load holding and high-flow on/off functions — lowering valves, accumulator isolation, unloading.

Installation and seal kits

Hex 7/8 in. (22,2 mm), 1 1/8 in. (28,6 mm), 1 1/4 in. (31,8 mm), 1 5/8 in. (41,3 mm); installation torque 30 - 35 lbf ft (41 - 47 Nm), 45 - 50 lbf ft (61 - 68 Nm), 150 - 160 lbf ft (203 - 217 Nm), 350 - 375 lbf ft (474 - 508 Nm). Replacement seal kits — series 1: Buna: 990310007, EPDM: 990310014, Viton: 990310006; series 2: Buna: 990203007, EPDM: 990203014, Viton: 990203006; series 3: Buna: 990016007, EPDM: 990016014, Viton: 990016006; series 4: Buna: 990018007, EPDM: 990018014, Viton: 990018006.

Ordering

Indus Hydraulics is an authorised Sun Hydraulics distributor in the UAE and supplies the range direct from Sun Hydraulics. Quote the base model and its configuration letters — for example DFCJXCN — or describe the duty and we select the part. We confirm the full ordering code with the quotation.

Identification

ParameterValue
Valve function2-Way 2-Stage Solenoid-Operated Poppet Valve
Series (frame sizes)1 to 4
CavityT-13A, T-5A, T-16A, T-18A

Performance

ParameterValue
Capacity15 gpm to 120 gpm (60 L/min to 480 L/min)
Max operating pressure5000 psi (350 bar)
Max leakage10 drops/min.@5000 psi (0,7 cc/min.@350 bar)

Configuration

ParameterValue
Control / adjustmentD — Twist/Lock (Dual) Manual Override, L — Twist/Lock (Detent) Manual Override, M — Manual Override, T — Twist (Momentary) Manual Override, X — No Manual Override; C — Normally Closed, H — Normally Open
Seal materialN — Buna-N, V — Viton, E — EPDM

Installation

ParameterValue
Valve hex size7/8 in. (22,2 mm), 1 1/8 in. (28,6 mm), 1 1/4 in. (31,8 mm), 1 5/8 in. (41,3 mm)
Installation torque30 - 35 lbf ft (41 - 47 Nm), 45 - 50 lbf ft (61 - 68 Nm), 150 - 160 lbf ft (203 - 217 Nm), 350 - 375 lbf ft (474 - 508 Nm)
Seal kitsseries 1: Buna: 990310007, EPDM: 990310014, Viton: 990310006; series 2: Buna: 990203007, EPDM: 990203014, Viton: 990203006; series 3: Buna: 990016007, EPDM: 990016014, Viton: 990016006; series 4: Buna: 990018007, EPDM: 990018014, Viton: 990018006
Weight.60 lb (0,30 kg) to 2.80 lb (1,30 kg)

Shipping & lead time

Lead TimeEx-stock from Dubai — delivered within 3 working days in the UAE. Export orders ship on the lane stated for the destination.

Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations

Also known as

The same part, in the designations used across European and Gulf trade catalogues.

de
Hammerverschraubung Typ 740
fr
union à marteau type 740
es
unión de martillo tipo 740
it
giunto a martello tipo 740
RELATED · OFTEN PAIRED WITH

Engineers viewing this also looked at