Alloy Steel Boiler and Superheater Tubes

Seamless chrome-moly tubes for superheaters, reheaters and high-temperature exchangers, to ASTM A213 T-grades (T11, T22, T91 and others), A209 and EN 10216-2. Made to ASTM A213 / SA-213, ASTM A209 / SA-209, ASTM A1016. Supplied from Dubai with an Indus part number for each size and mill test certificates on request.
Key features
- Product type: Alloy Steel Boiler and Superheater Tubes
- Construction: Seamless, cold drawn or hot finished
- Standards: ASTM A213 / SA-213, ASTM A209 / SA-209, ASTM A1016, EN 10216-2, DIN 17175 (superseded by EN 10216-2), GB/T 5310, JIS G3462, BS 3059
- Base tube material: A213 T5/T9/T11/T12/T22/T91; A209 T1/T1a/T1b; 16Mo3; 13CrMo4-5; 10CrMo9-10; 15CrMoG; 12Cr1MoVG
- Outside diameter: 38.1–76.2 mm
- Wall thickness: 3.05–5.16 mm
- Product type
- Alloy Steel Boiler and Superheater Tubes
- Construction
- Seamless, cold drawn or hot finished
- Base tube material
- A213 T5/T9/T11/T12/T22/T91; A209 T1/T1a/T1b; 16Mo3; 13CrMo4-5; 10CrMo9-10; 15CrMoG; 12Cr1MoVG
Product description
Seamless chrome-moly tubes for superheaters, reheaters and high-temperature exchangers, to ASTM A213 T-grades (T11, T22, T91 and others), A209 and EN 10216-2. The grade sets the temperature: higher chrome and molybdenum carry the tube further into the creep range.
Specification
- ASTM A213 size scope: ID 3.2 mm to OD 127 mm; min wall 0.4–12.7 mm (other sizes permitted)
- T91 heat treatment: Normalize 1040–1080 °C + temper 730–800 °C; anneal not permitted
- T11/T22 tensile: 415 MPa min, 205 MPa yield, 30% elongation; 163 HBW max
- EN 10216-2 alloy delivery condition: 16Mo3 +N; 13CrMo4-5 and 10CrMo9-10 +NT
- Equivalent grades (indicative): T1/T1a ≈ 16Mo3/15Mo3 ≈ STBA12/13; T11/T12 ≈ 13CrMo4-5 (13CrMo44) ≈ STBA23/STBA22 ≈ BS 3604 / 3059-2 620-460; T22 ≈ 10CrMo9-10 (10CrMo910) ≈ STBA24 ≈ BS 3059-2 622-490; T9 ≈ X11CrMo9-1 ≈ STBA26; T91 ≈ X10CrMoVNb9-1 ≈ STBA28 (indicative — check each tender)
- Max service temperature (indicative): 13CrMo4-5 class about 550–560 °C; 10CrMo9-10 class about 575–580 °C; 9Cr-1Mo-V (T91) class up to about 650 °C
- OD tolerance, cold-finished seamless and welded tube (mm): <25.4: ±0.10; 25.4–38.1: ±0.15; >38.1–<50.8: ±0.20; 50.8–<63.5: ±0.25; 63.5–<76.2: ±0.30; 76.2–101.6: ±0.38
- Wall tolerance, cold-finished minimum-wall tube: 0/+20% for OD ≤38.1 mm; 0/+22% for OD >38.1 mm
- Wall tolerance, hot-finished minimum-wall tube: ≤2.4 mm: 0/+40%; 2.4–3.8: 0/+35%; 3.8–4.6: 0/+33%; >4.6: 0/+28%
- Hydrostatic test pressure: P = 32000·t/D psi (220.6·t/D MPa), capped by A450 Table 7 (highest cap 4500 psi / 31 MPa)
Standards
ASTM A213 / SA-213, ASTM A209 / SA-209, ASTM A1016, EN 10216-2, DIN 17175 (superseded by EN 10216-2), GB/T 5310, JIS G3462, BS 3059. Equivalent grades across ASTM, EN, DIN, JIS and GB/T standards are indicative; we check them against each tender.
Materials
- Tube: A213 T5/T9/T11/T12/T22/T91; A209 T1/T1a/T1b; 16Mo3; 13CrMo4-5; 10CrMo9-10; 15CrMoG; 12Cr1MoVG
Testing and documents
- A213: heat and product analysis, tensile, hardness, flattening, flaring, hydrostatic or NDT (E213/E309/E570)
- Mills recommend combining two NDT methods (UT to E213 and eddy current to E309) for A209/A213
- Mill test certificate to EN 10204 3.1 on request; third-party inspection can be arranged against your inspection and test plan
Where it is used
- Fired-heater and refinery boiler superheater coils
- HRSG superheaters and reheaters in combined-cycle power and desalination plants
Sizes
10 sizes, each under its own Indus part number in the size table. These are the common sizes; others are made on request.
Ordering
Quote the Indus part number from the size table, or send the standard and grade, the outside diameter and wall (BWG or millimetres, minimum or average wall), the length and the quantity. We quote with the mill certificates and the inspection you need.
Identification
| Parameter | Value |
|---|---|
| Product type | Alloy Steel Boiler and Superheater Tubes |
| Construction | Seamless, cold drawn or hot finished |
Compliance
| Parameter | Value |
|---|---|
| Standards | ASTM A213 / SA-213, ASTM A209 / SA-209, ASTM A1016, EN 10216-2, DIN 17175 (superseded by EN 10216-2), GB/T 5310, JIS G3462, BS 3059 |
Construction
| Parameter | Value |
|---|---|
| Base tube material | A213 T5/T9/T11/T12/T22/T91; A209 T1/T1a/T1b; 16Mo3; 13CrMo4-5; 10CrMo9-10; 15CrMoG; 12Cr1MoVG |
Dimensions
| Parameter | Value |
|---|---|
| Outside diameter | 38.1–76.2 mm |
| Wall thickness | 3.05–5.16 mm |
| Length | Random or fixed lengths; cut to length on request |
| Size table | Common sizes |
Quality
| Parameter | Value |
|---|---|
| Testing | A213: heat and product analysis, tensile, hardness, flattening, flaring, hydrostatic or NDT (E213/E309/E570); Mills recommend combining two NDT methods (UT to E213 and eddy current to E309) for A209/A213 |
| Certification | Mill test certificate to EN 10204 3.1 on request; third-party inspection by arrangement |
Application
| Parameter | Value |
|---|---|
| Typical services | Fired-heater and refinery boiler superheater coils; HRSG superheaters and reheaters in combined-cycle power and desalination plants |
Shipping & lead time
Sizes & part numbers
10 sizes- Indus part no.IH-TF-AB-AL-0381-419
- O.D. (mm)
- 38.10
- O.D. (in)
- 1-1/2
- BWG
- 8
- Min. wall (mm)
- 4.19
- Min. wall (in)
- 0.165
- Indus part no.IH-TF-AB-AL-0381-457
- O.D. (mm)
- 38.10
- O.D. (in)
- 1-1/2
- BWG
- 7
- Min. wall (mm)
- 4.57
- Min. wall (in)
- 0.180
- Indus part no.IH-TF-AB-AL-0381-516
- O.D. (mm)
- 38.10
- O.D. (in)
- 1-1/2
- BWG
- 6
- Min. wall (mm)
- 5.16
- Min. wall (in)
- 0.203
- Indus part no.IH-TF-AB-AL-0508-419
- O.D. (mm)
- 50.80
- O.D. (in)
- 2
- BWG
- 8
- Min. wall (mm)
- 4.19
- Min. wall (in)
- 0.165
- Indus part no.IH-TF-AB-AL-0508-457
- O.D. (mm)
- 50.80
- O.D. (in)
- 2
- BWG
- 7
- Min. wall (mm)
- 4.57
- Min. wall (in)
- 0.180
- Indus part no.IH-TF-AB-AL-0635-305
- O.D. (mm)
- 63.50
- O.D. (in)
- 2-1/2
- BWG
- 11
- Min. wall (mm)
- 3.05
- Min. wall (in)
- 0.120
- Indus part no.IH-TF-AB-AL-0635-419
- O.D. (mm)
- 63.50
- O.D. (in)
- 2-1/2
- BWG
- 8
- Min. wall (mm)
- 4.19
- Min. wall (in)
- 0.165
- Indus part no.IH-TF-AB-AL-0635-457
- O.D. (mm)
- 63.50
- O.D. (in)
- 2-1/2
- BWG
- 7
- Min. wall (mm)
- 4.57
- Min. wall (in)
- 0.180
Show all 10 sizesShow fewer sizes
- Indus part no.IH-TF-AB-AL-0762-305
- O.D. (mm)
- 76.20
- O.D. (in)
- 3
- BWG
- 11
- Min. wall (mm)
- 3.05
- Min. wall (in)
- 0.120
- Indus part no.IH-TF-AB-AL-0762-419
- O.D. (mm)
- 76.20
- O.D. (in)
- 3
- BWG
- 8
- Min. wall (mm)
- 4.19
- Min. wall (in)
- 0.165
O.D. (mm) — Outside diameter of the tube or pipe in millimetres. O.D. (in) — The same outside diameter in inches, as the trade orders it. BWG — Birmingham Wire Gauge of the wall, the usual way heat-exchanger tube wall is ordered. Min. wall (mm) — Minimum wall thickness in millimetres. Min. wall (in) — The same minimum wall in inches.
These are typical sizes for the range, not a full mill list. Other diameters, walls, fin geometries and lengths are made to order: tell us the standard and grade, the O.D. and wall, and the length you need. Mill test certificates to EN 10204 3.1 are available on request.
What are Alloy Steel Boiler and Superheater Tubes used for?▾
How do I read an Indus part number for Alloy Steel Boiler and Superheater Tubes, such as IH-TF-AB-AL-0381-419?▾
What sizes do Alloy Steel Boiler and Superheater Tubes come in?▾
What do I need to send to order Alloy Steel Boiler and Superheater Tubes to the right size and grade?▾
What is the maximum service temperature of Alloy Steel Boiler and Superheater Tubes?▾
What tests and certificates come with Alloy Steel Boiler and Superheater Tubes?▾
Which materials and grades are Alloy Steel Boiler and Superheater Tubes available in?▾
Which standards apply to Alloy Steel Boiler and Superheater Tubes?▾
What do Alloy Steel Boiler and Superheater Tubes connect to or fit with?▾
How should Alloy Steel Boiler and Superheater Tubes be inspected on receipt and stored?▾
How are Alloy Steel Boiler and Superheater Tubes shipped, and can they be exported from Dubai?▾
Do you keep Alloy Steel Boiler and Superheater Tubes in stock in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog
Written about this part
Heat-transfer tubes
A179 vs A192 vs A210 vs A213: choosing boiler and exchanger tube
Four ASTM standards cover most carbon and alloy steel tube in exchangers, boilers and superheaters. What each is for, how they differ in chemistry and strength, which tests they carry, and how to choose — with the grade tables.
3 min read
Heat-transfer tubes
From DIN 17175 and DIN 1629 to EN 10216: what replaced what
Old drawings still call up St35.8, St45.8, 15Mo3 and 13CrMo44 to DIN 17175, and St37.0 or St52.0 to DIN 1629. Those standards are withdrawn. Which EN 10216 grades replaced them, how close the match is, and how to order tube for an old drawing.
3 min read
Heat-transfer tubes
Reading a mill test certificate to EN 10204 3.1
Every length of pressure tube should be traceable to a certificate. What EN 10204 types 2.1, 2.2, 3.1 and 3.2 mean, what a 3.1 certificate for tube should contain, and the checks to make before the tube goes into a bundle.
3 min read
