Nickel-Alloy U-Bend Tubes

U-tubes in nickel 200 and 201 and nickel alloys 400, 600, 800 and 825 to ASTM B163 and alloy 625 to ASTM B444, for corrosive and high-temperature exchanger service. Made to ASTM B163, ASTM B444, ASTM B407. Supplied from Dubai with an Indus part number for each size and mill test certificates on request.
Key features
- Product type: Nickel-Alloy U-Bend Tubes
- Construction: Bent from straight seamless or welded tube
- Standards: ASTM B163, ASTM B444, ASTM B407, ASTM B423, ASTM E571, ASTM B165
- Base tube material: N04400; N06600; N06625; N08800; N08825
- Outside diameter: 19.05–25.4 mm
- Wall thickness: 1.65–2.11 mm
- Product type
- Nickel-Alloy U-Bend Tubes
- Construction
- Bent from straight seamless or welded tube
- Base tube material
- N04400; N06600; N06625; N08800; N08825
Product description
U-tubes in nickel 200 and 201 and nickel alloys 400, 600, 800 and 825 to ASTM B163 and alloy 625 to ASTM B444, for corrosive and high-temperature exchanger service.
Specification
- Minimum bend radius: 1.5×OD centreline radius available; dimensional tolerances guaranteed from 2×OD
- Wall thinning at the bend: Per the governing specification on the order (ASTM A688 / TEMA, or A556 / B395) — no single percentage
- Bend heat treatment: To order: stress-relief or solution anneal of the bend plus ~150 mm of leg (A688), or ≥300 mm where the project specification requires
- Leg length: Up to ~12 m typical; straight tube up to 30 m on request
- ASTM B163 scope: Seamless Ni and Ni-alloy condenser/HX tube, OD ≤76.2 mm (3 in), min wall ≤3.76 mm or average wall ≤4.19 mm
- Alloys in B163: N02200, N02201, N04400, N06600, N06601, N06690, N08800, N08810, N08811, N08825 and others — N06625 is NOT in B163
- Welded equivalents (maker mapping): 825 B704; 800 B515; 600 B516; 400 B730 (seamless all B163) (indicative — check each tender)
- B163 OD tolerance: N04400: 15.9–38.1 mm ±0.13 mm; N06600/N08800/N08825: 15.9–38.1 mm ±0.19 mm; over 38.1–76.2 mm ±0.25 mm
- B163 wall tolerance: Average wall ±10 % (15.9–38.1 mm OD; ±12.5 % below 15.9); minimum wall +20/−0 % (+22 % over 38.1 mm)
- B163 hydrostatic test: 1000 psi (6.9 MPa), unless fibre stress P = 2St/D would exceed S (e.g. annealed N04400 120.6 MPa; annealed N06600 137.9 MPa)
- B444 N06625 grades: Grade 1 annealed (871 °C min) for service up to 593 °C; Grade 2 solution annealed (1093 °C min) above 593 °C
- ASTM A688 scope: U-bend clauses in nickel specs: B163, B444, B407, B423 contain no U-bend section; bend geometry follows TEMA / A688-form rules on the order; Wall thinning: t_before ≥ t1·(1 + do/4R) (TEMA form); Ovality: ≤10 % of nominal OD (R ≥ 2·D basis); Alloy 400 in HF alkylation: Stress relieve tube U-bends at about 620 °C (1150 °F); cold work from bending is enough to start SCC if oxygen is present; Alloy 600 U-bend stress relief: A 705 °C (1300 °F) / 5 min in-situ stress-relief cycle was qualified for Alloy 600 U-bends; Bend HT by agreement (TEMA paraphrase): Heat treatment to relieve embrittlement/SCC risk from cold bending is by agreement between maker and purchaser
Standards
ASTM B163, ASTM B444, ASTM B407, ASTM B423, ASTM E571, ASTM B165. Equivalent grades across ASTM, EN, DIN, JIS and GB/T standards are indicative; we check them against each tender.
Materials
- Tube: N04400; N06600; N06625; N08800; N08825
Testing and documents
- B163: hydro 6.9 MPa (fibre-stress limited) or electric NDE, maker's option unless ordered
- Ovality of annealed tube within 2 % of average OD (B423)
- Mill test certificate to EN 10204 3.1 on request; third-party inspection can be arranged against your inspection and test plan
Where it is used
- Bio/green-diesel condensers and HCl service — Alloy 625
- HF alkylation condensers — N04400
- Refinery hydrotreater REAC/FEAC, sour-water strippers, amine coolers — Alloy 825
- Seawater-cooled offshore exchangers — duplex or Alloy 625
Sizes
4 sizes, each under its own Indus part number in the size table. The table lists typical sizes for the range; other sizes are made on request.
Ordering
Quote the Indus part number from the size table, or send the standard and grade, the outside diameter and wall (BWG or millimetres, minimum or average wall), the length and the quantity, with the bend schedule: centreline radius and leg length for each row, and any heat treatment of the bends. We quote with the mill certificates and the inspection you need.
Identification
| Parameter | Value |
|---|---|
| Product type | Nickel-Alloy U-Bend Tubes |
| Construction | Bent from straight seamless or welded tube |
Compliance
| Parameter | Value |
|---|---|
| Standards | ASTM B163, ASTM B444, ASTM B407, ASTM B423, ASTM E571, ASTM B165 |
Construction
| Parameter | Value |
|---|---|
| Base tube material | N04400; N06600; N06625; N08800; N08825 |
Dimensions
| Parameter | Value |
|---|---|
| Outside diameter | 19.05–25.4 mm |
| Wall thickness | 1.65–2.11 mm |
| Length | Random or fixed lengths; cut to length on request |
| Bend radius | 1.5×OD centreline radius available; dimensional tolerances guaranteed from 2×OD |
| Size table | Typical sizes — other sizes on request |
Quality
| Parameter | Value |
|---|---|
| Testing | B163: hydro 6.9 MPa (fibre-stress limited) or electric NDE, maker's option unless ordered; Ovality of annealed tube within 2 % of average OD (B423) |
| Certification | Mill test certificate to EN 10204 3.1 on request; third-party inspection by arrangement |
Application
| Parameter | Value |
|---|---|
| Typical services | Bio/green-diesel condensers and HCl service — Alloy 625; HF alkylation condensers — N04400; Refinery hydrotreater REAC/FEAC, sour-water strippers, amine coolers — Alloy 825 |
Shipping & lead time
Sizes & part numbers
4 sizes- Indus part no.IH-TF-UN-NI-0190-165
- O.D. (mm)
- 19.05
- O.D. (in)
- 3/4
- BWG
- 16
- Wall (mm)
- 1.65
- Indus part no.IH-TF-UN-NI-0190-211
- O.D. (mm)
- 19.05
- O.D. (in)
- 3/4
- BWG
- 14
- Wall (mm)
- 2.11
- Indus part no.IH-TF-UN-NI-0254-165
- O.D. (mm)
- 25.40
- O.D. (in)
- 1
- BWG
- 16
- Wall (mm)
- 1.65
- Indus part no.IH-TF-UN-NI-0254-211
- O.D. (mm)
- 25.40
- O.D. (in)
- 1
- BWG
- 14
- Wall (mm)
- 2.11
O.D. (mm) — Outside diameter of the tube or pipe in millimetres. O.D. (in) — The same outside diameter in inches, as the trade orders it. BWG — Birmingham Wire Gauge of the wall, the usual way heat-exchanger tube wall is ordered. Wall (mm) — Wall thickness in millimetres: minimum or average wall per the governing standard and the order.
These are typical sizes for the range, not a full mill list. Other diameters, walls, fin geometries and lengths are made to order: tell us the standard and grade, the O.D. and wall, and the length you need. Mill test certificates to EN 10204 3.1 are available on request.
What are nickel-alloy U-bend tubes and what are they used for?▾
What sizes do the nickel-alloy U-bend tubes come in?▾
How do I choose the alloy for nickel-alloy U-bend tubes?▾
What test pressure applies to nickel-alloy U-bend tubes?▾
How do I read the Indus part number for nickel-alloy U-bend tubes?▾
Are there welded equivalents for ASTM B163 nickel-alloy tube?▾
Which nickel alloys are supplied as U-bend tubes?▾
Which standards and certificates apply to nickel-alloy U-bend tubes?▾
How tight can nickel-alloy U-bend tubes be bent?▾
Do nickel-alloy U-bends need heat treatment after bending?▾
Where are nickel-alloy U-bend tubes used?▾
Does Indus stock nickel-alloy U-bend tubes in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog
